JVC GM X50U manual Changing the Resistance of the RGB B Input Terminals

Changing the Resistance of the RGB B

Input Terminals

You can set the resistance of the two of the RGB B input terminals to either HIGH (1 kΩ) or LOW (75 Ω):

•HD/Cs (Horizontal sync/Composite) terminal

•VD (Vertical sync) terminal.

HIGH is the normal setting. Change the setting to LOW when you use a long connecting cord and the picture flickers and blurs on the screen.

1 Press MENU/EXIT (or MENU on the Monitor) to display the Main Menu.

		M A I N M E N U
Cursor (3)	P I C T U R E	A D J .
	S I Z E / P O S I T I O N A D J .
	F U N C T I O N S E L E C T
	S T A T U S D I S P L A Y
	E N T E R :	S E L E C T :	E X I T :
				M E N U

2 Press 5/∞ to move the cursor (3) to

“FUNCTION SELECT.”

3 Press 3 to display the Function

Selection Menu.

F U N C T I O N S E L E C T

	C O L O R T E M P .		: H I G H *
	A S P E C T		: P A N O R A M I C
	S I G N A L M O D E		: A U T O
	C O M P O . / R G B B		: R G B B
	S Y N C T E R M .		: H I G H
	r e s e t
A D J U S T :		S E L E C T :		E X I T :
					M E N U

*1 *2 *3

*1 “ASPECT” does not appear when 720/60p, 720/50p, 1080/60i (1035/60i), or 1080/50i signal is being input through the COMPONENT/RGB B input terminals.

*2 “SIGNAL MODE” appears only when VIDEO A, VIDEO B, or COMPONENT input is selected.

*3 “SYNC TERM.” appears only when the RGB B input is selected.

4 Press 5/∞ to move the cursor (3) to “SYNC TERM.”

5 Press 2/3 to select the terminal resistance.

Each time you press the button, the resistance alternates between “HIGH” and “LOW.”

HIGH: Initial setting. Normally select this.

LOW: When using a long connecting cord and the picture flickering and blurring on the screen.

6 Press MENU/EXIT (or MENU on the Monitor) twice to exit the menu operations.

Resetting the Function Selection Menu Settings

You can reset all the Function Selection Menu settings at a time.

1 Press MENU/EXIT (or MENU on the Monitor) to display the Main Menu.

		M A I N M E N U
Cursor (3)	P I C T U R E	A D J .
	S I Z E / P O S I T I O N A D J .
	F U N C T I O N S E L E C T
	S T A T U S D I S P L A Y
	E N T E R :	S E L E C T :	E X I T :
				M E N U

2 Press 5/∞ to move the cursor (3) to

“FUNCTION SELECT.”

3 Press 3 to display the Function

Selection Menu.

F U N C T I O N S E L E C T

	C O L O R T E M P .		: H I G H *
	A S P E C T		: P A N O R A M I C
	S I G N A L M O D E		: A U T O
	C O M P O . / R G B B		: R G B B
	S Y N C T E R M .		: H I G H
	r e s e t
A D J U S T :		S E L E C T :		E X I T :
					M E N U

*1 *2 *3

*1 “ASPECT” does not appear when 720/60p, 720/50p, 1080/60i (1035/60i), or 1080/50i signal is being input through the COMPONENT/RGB B input terminals.

*2 “SIGNAL MODE” appears only when VIDEO A, VIDEO B, or COMPONENT input is selected.

*3 “SYNC TERM.” appears only when the RGB B input is selected.

4 Press 5/∞ to move the cursor (3) to “reset.”

5 Press 3.

The confirmation screen appears.

r e s e t
A r e y o u s u r e ?
" Y E S " t h e n	k e y .

" N O " t h e n M E N U k e y .

6 Press 3 again to reset the adjustments.

To cancel the reset, press MENU/EXIT (or MENU on the Monitor).

7 Press MENU/EXIT (or MENU on the Monitor) twice to exit the menu operations.

21