Connecting to a computer directly Wi-Fi Direct | JVC GV-LS2 U

Connecting to a computer directly (Wi-Fi Direct)

Using the WPS function

1Press and hold the power button to power off.

2Disconnect the LAN cable that connects the camera to your computer.

3Set the network mode switch to "DIRECT".

4Press and hold the power button to power on. The record button starts blinking. Wait until it stops blinking and off.

5Establish a WPS connection on the computer. For connection, refer to the instruction manual of the device.

6Press and hold the "WPS" button.

When the "WPS" button stops blinking and stays lit, the connection is complete.

If no connection cannot be established within two minutes, the "WPS" button turns off. Try again, or set up manually.

Connecting manually

1Press and hold the power button to power off.

2Disconnect the LAN cable that connects the camera to your computer.

3Set the network mode switch to "DIRECT".

4Press and hold the power button to power on. The record button starts blinking. Wait until it stops blinking and off.

5Connect to DIRECT-**JVCCAM via wireless LAN of the computer.

•For connection, refer to the instruction manual of the device.

•The password is "password" at the time of purchase.

Preparation

23

Image 23

JVC GV-LS2 U manual Connecting to a computer directly Wi-Fi Direct

Contents

GV-LS2 Table of Contents Network CAMERA/PAN Tilter Manage Connecting an External MicConnecting the AV Cord Verifying the Accessories Front Back Component Names and FunctionsCamera Bottom Introduction Top Bottom Back PantilterFront Use Setting Addition SetupExample 2 Record birds coming to a feeder on the balcony Example 3 Live-stream a performance in a studio Starting shooting Flow of Connection/Setup Attach the LAN cable to the unit Connecting the Camera to Your ComputerRequired operating environment Connecting the AC Adapter List Configuring the initial settingsIP Address Subnet Mask Http//condigured IP address8000 Select Common Settings in Manage Configuring the Camera SettingsAdjusting the clock Enter USERNAME, PASSWORD, and Password Confirm Setting the user name and passwordClick the Update button on the right Change Administrator USER/PASSWORD Select an option from MAX Frame Rate MotionJPEG Select Stream Settings in NetworkMPEG-2 TS 720x576/MotionJPEG MPEG-2 TS 1920x1080/MotionJPEG Obtaining a Ddns account Setting up the Ddns accountSelect Monitoring Settings in Network Click the ADD button Adding a camera drivers user Subnet Mask Establishing a wired connection to the access pointDefault Gateway Changing the Connection Destination Select Wireless Network in Network Connecting to the access point wirelessly Wi-FiUsing the WPS function Searching and connecting to the access point Enter Password Click the Save button Connecting manually Connecting to a computer directly Wi-Fi Direct Click the Save button Select Common Settings in Manage Connecting Multiple Cameras Screw and fix the camera Attaching the PantilterAttaching the Pantilter Push the camera straight down Loosen the camera fixing screw sufficiently Connecting the AC adapterRemoving the pantilter Remove all tape from the pantilter Connect the camera to your computer via the LAN cable Establishing a wired connectionAttach the conversion cable to the stopper of the LAN cable Attach the LAN cable to the unit in numerical order Compatible SD cards Inserting/Removing an SD CardInserting Removing Approximate charging times Attaching/Removing the BatteryAttaching Charging Attaching to the hot shoe Connecting an External MicConnecting to the camera Connecting to the pantilter Connecting the AV Cord Starting/Stopping recording Using the Unit AloneTurning on/off the power Click the LOG in button Controlling from a Web BrowserLogging Status Controlling the camera Monitor tabMonitor File Management SD card Reload button Update images Setting buttonZoom ratio Configuring the camera settings Delete Managing files stored on the SD card File Management tabUse Folder/File lists Transfer LOG in User Checking the message history Status tabCamera Network Streaming images Installing JVC CAM Control Names of Apps for mobile terminals Using the Mobile TerminalInstalling the App for mobile terminals Information Setting Item ListWired Network Wireless Network SSID, Authenticate METHOD, Password Registered Access PointPassword Ddns Monitoring SettingsPort Number UPnP MAX Frame Rate MotionJPEG Stream SettingsStream 1 / Stream PAN Tilter Settings Camera Settings Media Management Common Settings Turn OFF Camera Power cannot be turned on remotely Connection TroubleshootingProblem Check Refer to Direct SetupURL Information Use Information Message Check Refer to Error messages Installed Update on this Incorrect PasswordNo Updates Available Update Corrupted Lamp Status List PowerWPS Power To execute, click the Exec button Resetting to the factory settingsDeleting Resetting the connection information Click the Exec button on the right To avoid hazards Battery Pack optionalTo prevent damage and prolong service life Updating the firmware Video SpecificationsConnectors Camera MPEG-2 TS Stream output formatAC adapter UIA324-12 Pantilter GV-LS2WUP JVC Kenwood Corporation 0812HO-MW-VM