Konica Minolta 5430 DL 82

6 Open the right side cover, and then use a coin to loosen the screws securing the transfer belt unit.

7 From the side where the left side cover was removed, hold the arm, and then carefully pull out the transfer belt unit.

8 Prepare a new transfer belt unit.

" Be careful not to touch the surface of the belt.

74	Replacing Consumables

Contents

Page Trademarks Copyright Notice Notice SOFTWARE LICENSE AGREEMENT Page Contents Getting Acquainted with Your Printer Utilities and Documentation CD-ROM System Requirements Selecting Driver Options/Defaults (For Windows) Uninstalling the Printer Driver Displaying Printer Driver Settings Using the Printer Driver Recognizing Status Display Alerts Using Media Media Specifications Media Types Loading Media Duplexing Printing the Configuration Page Preventing Media Misfeeds Understanding the Media Path Clearing Media Misfeeds Solving Problems with Media Misfeeds Introduction Getting Acquainted with Your Printer Space Requirements Printer Parts Rear View Accessory Front View with Options Software Installation CD-ROM Drivers Utilities System Requirements Selecting Driver Options/Defaults (For Windows) Uninstalling the Printer Driver (For Windows) Displaying Printer Driver Settings (For Windows) Using the Printer Driver Common Buttons Setup Tab Paper Tab Quality Tab Device Options Setting Tab Using the Windows Status Display and Printer Status Monitor Center Working with the Status Display Opening the Status Display and Showing the Supplies Status Altering the Size of the Status Display Window Using the Status Display Recognizing Status Display Alerts Recovering from a Status Display Alert Closing the Status Display Working With the Printer Status Monitor Center System Requirements Opening the Printer Status Monitor Center and Showing the Supplies Status Using the Printer Status Monitor Center Recognizing Printer Status Monitor Center Alerts Closing the Printer Status Monitor Center Printer Control Panel and Configuration Menu About the Control Panel Control Panel Indicators and Keys JOB CANCEL/CURRENT JOB or JOB CANCEL/ALL JOBS Toner Supply Indicators Configuration Menu Overview Configuration Menu Page Special Pages Menu FIG PAGE PAGES MAP Language Menu ON / OFF Resets the ENERGY SAVER, AUTO USER DEFAULT Network Menu DHCP DHCP SET:OFF BOOTP SET:ON BOOTP SET:OFF Consumables Menu BLACK TONER CYAN YELLOW Page Using Media Media Specifications Media Types Plain Paper (Recycled Paper) Thick Stock Envelopes Labels Letterhead Postcards Transparencies What Is the Guaranteed Imageable (Printable) Area Page Margins Loading Media Tray 1 (Multipurpose Cassette) Page Page Other Media Loading Envelopes 5 Load the envelopes flap side down in the tray " Up to 10 envelopes can be loaded into the tray at one time 7 Close Tray 8 Pull the lever, and then open the right side cover Page Page Loading Label Sheets/Postcards/Thick Stock/ Transparencies 5 Load the media face up in the tray " Up to 20 sheets can be loaded into the tray at one time Tray 2 and 3 (Optional Lower Feeder Units) Page 6 Close Tray 2 (Tray 3) Duplexing DUPLEX UNIT NOT ATTACHED Output Tray Media Storage Replacing Consumables Replacing Consumables Refilled Toner Cartridges About Toner Cartridges Page Do not hold a toner cartridge vertically Do not touch the OPC drum surface. This could lower image quality Page Page Page Page Replacing the Waste Toner Bottle WASTE BOTTLE FULL Page Page Replacing the Transfer Roller TRANS.ROLLER END Page Page ENGINE/SERVICE/RESET COUNTER TRANSFER ROLLER Replacing the Transfer Belt Unit TRANSFER END Page Page Page Page ENGINE/SERVICE/RESET COUNTER TRANSFER UNIT Page Page Maintaining the Printer Page Cleaning the Printer Exterior Media Rollers Duplex Option Feed Rollers Cleaning the Media Transfer Rollers for Tray 2 and Cleaning the Laser Lens of the Printer Troubleshooting Printing the Configuration Page CONFIG Preventing Media Misfeeds Understanding the Media Path Clearing Media Misfeeds Media Misfeed Messages and Clearing Procedures MEDIA JAM TRAY DUPLEX LOWER DUPLEX UPPER Page Page 4 Pull out Tray 1, and then remove all media from the tray 5 Fan the media you removed and then align it well 6 Load the media face up in Tray Make sure that the media is flat Do not load paper above the mark Clearing a Media Misfeed in Tray 2 and Page Clearing a Media Misfeed from the Duplex Option Clearing a Media Misfeed from the Fuser Unit Page Page Clearing a Media Misfeed from the Transfer Roller Page Page Solving Problems with Media Misfeeds Solving Problems with Media Misfeeds Page Solving Other Problems TONER LOW much (NO GENUINE TONER X is dis Page Page Solving Problems with Printing Quality Page Page Page TONER LOW or TONER EMPTY Page Status, Error, and Service Messages Standard Status Messages CALIBRATING CANCELLING JOB ENERGY SAVER Error Messages (Warning) FUSER LIFE END FUSER LIFE LOW SIZE MISMATCH when AUTO CON TRANS.ROLLER LOW TRAY X EMPTY UNSUPPORTED DIMM WASTE:NEAR FULL Error Messages (Operator Call) COVER OPEN DUPLEX FRONT SIDE UNDEFINED NO GENUINE TONER PUT MEDIA : TRAY “MEDIA” “SIZE” REPLACE TONER SIZE/TYPE ERROR TONER LIFE END X TONER NOT INSTALLED Service Messages AIDC SENSOR COMMUNICATION CONTROLLER DIMM Installing Accessories Antistatic Protection Dual In-LineMemory Module (DIMM) Installing a DIMM Dual In-LineMemory Module (DIMM) SPECIAL PAGES/PRINT CONFIG PAGE MENU Duplex Option Installing the Duplex Option 3 Remove the door at the side of the right side cover 4 Prepare the duplex option 5 Attach the duplex option, as shown in the illustration Page Lower Feeder Unit Kit Contents Installing the Lower Feeder Unit Page Page Page Appendix Safety Specifications Technical Specifications Printer Page Technical Specifications Consumable Life Expectancy Chart Our Concern for Environmental Protection Index Maintenance Media Media misfeed Media path Media storage