Korg PA50, PA50sd 047: Dynam.Delay

205
Effects
ER/Delay
The “Src” parameter sets the modulation source that
resets the LFO. For example, you can assign Gate as a mod-
ulation source so that the sweep always starts from the
specified point.
“L LFO Phase” and “R LFO Phase” set the phase obtained
when the left and right LFOs are reset. In this way, you can
create changes in pitch sweep for the left and right chan-
nels individually.
The effect is off when a value of the modulation source speci-
fied in the “Src” parameter is 63 or smaller, and the effect is on
when the value is 64 or higher. The LFO is triggered and reset to
the “L LFO Phase” and “R LFO Phase” settings when the value
changes from 63 or smaller to 64 or higher.
047: Dynam.Delay
(Stereo Dynamic Delay)
This stereo delay controls the level of delay according to the
input signal level. You can use this as a ducking delay that
applies delay to the sound only when you play keys at a high
velocity or only when the volume level is low.
a: Control Target
This parameter selects no level control, delay output con-
trol (effect balance), or feedback amount control.
a: Polarity, b: Threshold, b: Offset, c: Attack, d: Release
The “Offset” parameter specifies the value for the “Con-
trol Target” parameter (that is set to None), expressed as
the ratio relative to the parameter value (the “Wet/Dry”
value with “Control Target”=Out, or the “Feedback”
value with “Control Target”=FB).
When “Polarity” is positive, the “Control Target” value is
obtained by multiplying the parameter value by the “Off-
set” value (if the input level is below the threshold), or
equals the parameter value if the input level exceeds the
threshold.
When “Polarity” is negative, Control Target value equals
the parameter value if the input level is below the thresh-
old, or is obtained by multiplying the parameter value by
the “Offset” value if the level exceeds the threshold.
The “Attack” and “Release” parameters specify attack
time and release time of delay level control.
a
Control Target
Selects from no control, output, and feedback
None, Out, FB
☞
Polarity
Reverses level control
+, –
☞
b
Threshold
Sets the level to which the effect is applied
0...100
☞
Offset
Sets the offset of level control
0...100
☞
cAttack
Sets the attack time of level control
1...100
☞
dRelease
Sets the release time of level control
1...100
☞
eL Delay Time [msec]
Sets the delay time for the left channel
0.0...680.0msec
fR Delay Time [msec]
Sets the delay time for the right channel
0.0...680.0msec
gFeedback
Sets the feedback amount
–100...+100
Delay
Left
Right
Feedback Spread
Wet / Dry
Wet / Dry
Stereo In - Stereo Out
High DampLow Damp
High DampLow Damp
Threshold
+
Delay
FB Out
Control Target
Attack, Release
Envelope
h
High Damp [%]
Sets the damping amount in the high range
0...100%
☞ Fx:043
Low Damp [%]
Sets the damping amount in the low range
0...100%
☞ Fx:043
iSpread –100...+100
Sets the width of the stereo image of the effect sound ☞ Fx:043
j
Wet/Dry Dry, 1:99...99:1, Wet
Table , “Sets the balance between the effect and dry sounds,” on page 175
Src Off...Tempo
Table , “Selects the modulation source of the effect balance,” on page 175
Amt
Table , “Sets the modulation amount of the effect bal-
ance,” on page 175
–100...+100
Dynamic Delay
Threshold
Dry
Envelope
Wet
Control Target=Out
Polarity= (–)
Wet
Control Target=Out
Polarity= (+)
Delay Time
Time
(Ducking Delay)
Release
Attack
Level