RS-232C/RS-422A Protocol, H1 Baud rate | Kyocera FS-600 instruction

Appendix C Host Computer Interface

RS-232C/RS-422A Protocol

A protocol is a set of rules the computer follows in sending data to the printer. The RS-232C/RS-422A parameters are stored in battery backed-up memory. They are indicated on the status printout. They can be changed by the FRPO (firmware reprogram) command described in the Programming Manual. The parameters and their identification codes are given below.

H1: Baud rate

Parameter value	Baud rate
12	1200
24	2400
48	4800
96	9600
19	19200
38	38400
57	57600
11	115200

The factory setting is 9600 baud.

H2: Data bits

7 or 8, factory-set to 8.

H3: Stop bits

1 or 2, factory-set to 1.

C-11

Image 131

Kyocera FS-600 manual RS-232C/RS-422A Protocol, H1 Baud rate, H2 Data bits, H3 Stop bits

Contents

Italiano Regarding Tradenames Introduction Iii Typeface Trademark Acknowledgement FCC statement Conforming to the Class B limits Safety information Interface connectors Viii Cdrh regulations Ozone concentration Important Safeguards ISO Canadian Department of Communications compliance statement According to Council Directive 89/336/EEC and 73/23/EEC CE Marking Directive Declaration of Conformity Australia Xiii Xiv Moving the Printer DisclaimerProlonged Non-Use and Moving the Printer Prolonged Non-use Xvi Environmentally benign waste parts IntroductionSuperb print quality Long life modules Simple Network Management Protocol Snmp compliance Wide variety of internal symbol setsNew printer control language, Prescribe IIe Automatic rotation of fonts and graphics Options Contents Xxi Chapter Installing Printer ∙ Near the computer Environmental Requirements of the Page PrinterPlaces to Avoid Basic requirements Current capacity ∙ Level and well supportedVoltage Frequency Power Supply Surrounding space Grounding Unpacking and Inspection Basic handling precautions List of packaged contents Moving the Printer Names of Parts Interior View Setup and Connections Install the printer on the paper feeder. Option Remove the process unit protective cover Shake four or five times Install the toner container Close the top cover Add paper Load Limit Close the cassette cover Open the paper stopper on the face-down tray Open the face-up output tray when the tray is being used Connect the printer to the computer Parallel Interface Connection Be sure to connect the ground wire of the printer to ground Attach the power cordBe sure the printers power switch is turned off Control Panel Test the printer Echo !R! Stat Exit PRN Test the interface with the computer Install the printer driver Installing the Page Printer Setup and Connections Installing Under Windows3.1 Setup and Connections Installing the Page Printer Expanding Memory Description given below is intended for service personnel Precautions on the Handling of Extended Simm Installing Simm Screws Pull the main circuit board all the way out of the printer Catch Socket Expanding Memory Testing Extended Memory Chapter Operating Printer Control Panel Indicators on the Control Panel Indicators Functions of the control keys are given in the table below Control Keys KIR 2 Level KIR Level Ecoprint mode Manual Paper Feeding Sub-Tray Overhead Projection OHP Film Feeding Envelopes Auto Manual Feeding Returning the Manual Feed Tray Fonts Fonts Option Fonts List of FontsBitmap Fonts Scalable Fonts Resident Scalable Fonts Resident Scalable Fonts Kpdl Fonts Kpdl Fonts Chapter Maintenance Toner Kit to be Used Toner Container ReplacementToner Container Replacement Interval Maintenance Replenishing Toner Cap Carefully remove the protective seal Toner Container Grooves Toner Container Replacement Printer Interior Cleaning Cleaning Maintenance Chapter Troubleshooting Press the on LINE/STATUS key General Guide See Appendix C Print Quality Problems On next Chapter Commands. If the problem occurs only with a specific file or Maintenance Indications Indicators Open the printer and correct the paper jam. See Indicators Error Indications Jam at the Face-down and Face-up Trays Correcting a Paper Jam Paper Cassette Paper Feeder Option Paper Feeder’s Cassette Jam Inside the Printer Troubleshooting Appendix a Printer Specifications Printer Specifications Page Appendix B Paper Selection Usable Paper General Guidelines Paper Specifications Paper Specifications Composition Selecting the Right PaperCondition of the Paper Smoothness Paper Size Thickness Basis WeightMoisture Content Curl Paper GrainOther Paper Properties Stiffness Specially treated paper Electrostatic propertiesQuality control Packaging Special Paper Preprinted Paper Overhead Projection OHP Film OHP Film SpecificationsColored Paper Labels PostcardsEnvelopes Appendix C Host Computer Interface Parallel Interface Table C . Parallel Connector Pin Assignments Interface SignalsPage Auto-Feed nAutoFd Pin Paper Empty PError PinError* nFault Pin On-Line Select Pin Select In NSelectIn Pin Power Ready PinAuxiliary output 1 Pin RS-232C interface Interface SignalsTable C . RS-232C Signal Pin Assignments Serial RS-232C/RS-422A Interface Option RTS Request To Send Pin SG Signal Ground PinTXD Transmit Data Pin RXD Receive Data Pin RS-422A interface Table C.3. RS-422A Signal Pin Assignments SDB Send Data Pin SDA Send Data Inverted Pin Overview of Signals RS-422ASerial Connector RDB Receive Data Pin RDA Receive Data Inverted Pin H3 Stop bits RS-232C/RS-422A ProtocolH1 Baud rate H2 Data bits H7 Buffer nearly-empty threshold H4 ParityH5 Protocol logic H6 Buffer nearly-full threshold H8 Received-data buffer size Prescribe Frpo D0 command Preparing an RS-232C Cable RS-232C Cable Connection Connecting the Printer to the Computer Cmode LPT1=COM1 Appendix D Indicators Receiving data WaitingOff line Ready On line Sleeping Processing dataAdding paper Selecting paper size Toner status Paper jamMemory overflow Top cover open ˜˜˜˜˜˜˜˜˜ Lit ˜˜˜˜˜˜˜˜˜ ˜ Off Call-service person errors Controller system error F3 error Index MRU