Prescribe Frpo D0 command | Kyocera FS-600 specs

Appendix C Host Computer Interface

The gap between the nearly-full and nearly-empty thresholds allows the computer to send a fairly large amount of data in a continuous stream.

H8: Received-data buffer size

This is the size of the input buffer, specified in units of 10K bytes. The factory-set value is 6 meaning 60K bytes.

Note _____________________________________________________________________

Since DTR/DSR protocol is not used with the RS-422A standard, select a parameter value other than 0, 1, or 2 for the H5 setting when using the RS-422A interface.

PRESCRIBE FRPO D0 command

The PRESCRIBE FRPO D0 command is provided to allow manipulating XON/XOFF when an error has occurred on the serial interface. The following table summarizes the error status corresponding to different D0 values.

			Serial interface error
			error not handled		error handled
Timing of XON transfer to	XON sent every 3-5	D0	= 0 (default)	D0	= 1
host while Ready or	seconds
Waiting
	XON not sent	D0	= 10	D0	= 11

C-13

Image 133

Kyocera FS-600 manual Prescribe Frpo D0 command, H8 Received-data buffer size

Contents

Italiano Regarding Tradenames Introduction Iii Typeface Trademark Acknowledgement FCC statement Conforming to the Class B limits Safety information Interface connectors Viii Cdrh regulations Ozone concentration Important Safeguards ISO Canadian Department of Communications compliance statement According to Council Directive 89/336/EEC and 73/23/EEC CE Marking Directive Declaration of Conformity Australia Xiii Xiv Prolonged Non-Use and Moving the Printer DisclaimerProlonged Non-use Moving the Printer Xvi Superb print quality IntroductionLong life modules Environmentally benign waste parts New printer control language, Prescribe IIe Wide variety of internal symbol setsAutomatic rotation of fonts and graphics Simple Network Management Protocol Snmp compliance Options Contents Xxi Chapter Installing Printer Places to Avoid Environmental Requirements of the Page PrinterBasic requirements ∙ Near the computer Voltage ∙ Level and well supportedFrequency Current capacity Power Supply Surrounding space Grounding Unpacking and Inspection Basic handling precautions List of packaged contents Moving the Printer Names of Parts Interior View Setup and Connections Install the printer on the paper feeder. Option Remove the process unit protective cover Shake four or five times Install the toner container Close the top cover Add paper Load Limit Close the cassette cover Open the paper stopper on the face-down tray Open the face-up output tray when the tray is being used Connect the printer to the computer Parallel Interface Connection Be sure the printers power switch is turned off Attach the power cordBe sure to connect the ground wire of the printer to ground Control Panel Test the printer Echo !R! Stat Exit PRN Test the interface with the computer Install the printer driver Installing the Page Printer Setup and Connections Installing Under Windows3.1 Setup and Connections Installing the Page Printer Expanding Memory Description given below is intended for service personnel Precautions on the Handling of Extended Simm Installing Simm Screws Pull the main circuit board all the way out of the printer Catch Socket Expanding Memory Testing Extended Memory Chapter Operating Printer Control Panel Indicators on the Control Panel Indicators Functions of the control keys are given in the table below Control Keys KIR 2 Level KIR Level Ecoprint mode Manual Paper Feeding Sub-Tray Overhead Projection OHP Film Feeding Envelopes Auto Manual Feeding Returning the Manual Feed Tray Fonts Fonts Bitmap Fonts List of FontsScalable Fonts Option Fonts Resident Scalable Fonts Resident Scalable Fonts Kpdl Fonts Kpdl Fonts Chapter Maintenance Toner Container Replacement Interval Toner Container ReplacementToner Kit to be Used Maintenance Replenishing Toner Cap Carefully remove the protective seal Toner Container Grooves Toner Container Replacement Printer Interior Cleaning Cleaning Maintenance Chapter Troubleshooting Press the on LINE/STATUS key General Guide See Appendix C Print Quality Problems On next Chapter Commands. If the problem occurs only with a specific file or Maintenance Indications Indicators Open the printer and correct the paper jam. See Indicators Error Indications Jam at the Face-down and Face-up Trays Correcting a Paper Jam Paper Cassette Paper Feeder Option Paper Feeder’s Cassette Jam Inside the Printer Troubleshooting Appendix a Printer Specifications Printer Specifications Page Appendix B Paper Selection Usable Paper General Guidelines Paper Specifications Paper Specifications Condition of the Paper Selecting the Right PaperComposition Smoothness Paper Size Moisture Content Basis WeightThickness Other Paper Properties Paper GrainStiffness Curl Quality control Electrostatic propertiesPackaging Specially treated paper Special Paper Colored Paper OHP Film SpecificationsPreprinted Paper Overhead Projection OHP Film Envelopes PostcardsLabels Appendix C Host Computer Interface Parallel Interface Table C . Parallel Connector Pin Assignments Interface SignalsPage Error* nFault Pin Paper Empty PError PinOn-Line Select Pin Auto-Feed nAutoFd Pin Auxiliary output 1 Pin Power Ready PinSelect In NSelectIn Pin Table C . RS-232C Signal Pin Assignments Interface SignalsSerial RS-232C/RS-422A Interface Option RS-232C interface TXD Transmit Data Pin SG Signal Ground PinRXD Receive Data Pin RTS Request To Send Pin RS-422A interface Table C.3. RS-422A Signal Pin Assignments Serial Connector Overview of Signals RS-422ARDB Receive Data Pin RDA Receive Data Inverted Pin SDB Send Data Pin SDA Send Data Inverted Pin H1 Baud rate RS-232C/RS-422A ProtocolH2 Data bits H3 Stop bits H5 Protocol logic H4 ParityH6 Buffer nearly-full threshold H7 Buffer nearly-empty threshold H8 Received-data buffer size Prescribe Frpo D0 command Preparing an RS-232C Cable RS-232C Cable Connection Connecting the Printer to the Computer Cmode LPT1=COM1 Appendix D Indicators Off line WaitingReady On line Receiving data Adding paper Processing dataSelecting paper size Sleeping Memory overflow Paper jamTop cover open Toner status ˜˜˜˜˜˜˜˜˜ Lit ˜˜˜˜˜˜˜˜˜ ˜ Off Call-service person errors Controller system error F3 error Index MRU