Parallel Interface | Kyocera FS-600 specification

Parallel Interface

Parallel Interface

Parallel interface communication modes

The printer features the fast data transmission mode on the parallel interface. The parallel interface mode can be changed by using the PRESCRIBE FRPO O0 command. See the Programming manual (in the Kyocera Digital Library CD-ROM) for details.

Note______________________________________________________________________

Use a parallel printer cable that complies with the IEEE1284 standards.

Nibble (high) (FRPO O0, 5; [default])

High speed data communication is used in compliance with the IEEE 1284 standard. Ordinarily, you should leave this setting unchanged.

Auto (FRPO O0, 70;)

The printer automatically changes its communication mode to the one the host computer is currently using.

Normal (FRPO O0, 0;)

The printer uses the communication method described by the normal definitions of the Centronics interface.

High-speed (FRPO O0, 1;)

This mode enables faster data reception from the host computer by the normal definitions of the

Centronics interface..

C-2

Image 122

Kyocera FS-600 manual Parallel Interface

Contents

Italiano Regarding Tradenames Introduction Iii Typeface Trademark Acknowledgement FCC statement Conforming to the Class B limits Interface connectors Safety information Viii Ozone concentration Cdrh regulations Important Safeguards Canadian Department of Communications compliance statement ISO CE Marking Directive According to Council Directive 89/336/EEC and 73/23/EEC Xiii Declaration of Conformity Australia Xiv Prolonged Non-use DisclaimerProlonged Non-Use and Moving the Printer Moving the Printer Xvi Long life modules IntroductionSuperb print quality Environmentally benign waste parts Automatic rotation of fonts and graphics Wide variety of internal symbol setsNew printer control language, Prescribe IIe Simple Network Management Protocol Snmp compliance Options Contents Xxi Chapter Installing Printer Basic requirements Environmental Requirements of the Page PrinterPlaces to Avoid ∙ Near the computer Frequency ∙ Level and well supportedVoltage Current capacity Power Supply Grounding Surrounding space Basic handling precautions Unpacking and Inspection List of packaged contents Moving the Printer Names of Parts Interior View Setup and Connections Install the printer on the paper feeder. Option Remove the process unit protective cover Shake four or five times Install the toner container Close the top cover Add paper Load Limit Close the cassette cover Open the face-up output tray when the tray is being used Open the paper stopper on the face-down tray Connect the printer to the computer Parallel Interface Connection Be sure to connect the ground wire of the printer to ground Attach the power cordBe sure the printers power switch is turned off Test the printer Control Panel Test the interface with the computer Echo !R! Stat Exit PRN Install the printer driver Installing the Page Printer Setup and Connections Installing Under Windows3.1 Setup and Connections Installing the Page Printer Expanding Memory Precautions on the Handling of Extended Simm Description given below is intended for service personnel Installing Simm Screws Pull the main circuit board all the way out of the printer Catch Socket Expanding Memory Testing Extended Memory Chapter Operating Printer Control Panel Indicators Indicators on the Control Panel Control Keys Functions of the control keys are given in the table below KIR 2 Level KIR Level Ecoprint mode Manual Paper Feeding Sub-Tray Feeding Envelopes Overhead Projection OHP Film Auto Manual Feeding Returning the Manual Feed Tray Fonts Fonts Scalable Fonts List of FontsBitmap Fonts Option Fonts Resident Scalable Fonts Resident Scalable Fonts Kpdl Fonts Kpdl Fonts Chapter Maintenance Toner Kit to be Used Toner Container ReplacementToner Container Replacement Interval Maintenance Replenishing Toner Cap Carefully remove the protective seal Toner Container Grooves Toner Container Replacement Cleaning Printer Interior Cleaning Maintenance Chapter Troubleshooting General Guide Press the on LINE/STATUS key See Appendix C Print Quality Problems On next Chapter Commands. If the problem occurs only with a specific file or Indicators Maintenance Indications Open the printer and correct the paper jam. See Indicators Error Indications Correcting a Paper Jam Jam at the Face-down and Face-up Trays Paper Cassette Paper Feeder Option Paper Feeder’s Cassette Jam Inside the Printer Troubleshooting Appendix a Printer Specifications Printer Specifications Page Appendix B Paper Selection General Guidelines Usable Paper Paper Specifications Paper Specifications Composition Selecting the Right PaperCondition of the Paper Paper Size Smoothness Thickness Basis WeightMoisture Content Stiffness Paper GrainOther Paper Properties Curl Packaging Electrostatic propertiesQuality control Specially treated paper Special Paper Preprinted Paper Overhead Projection OHP Film OHP Film SpecificationsColored Paper Labels PostcardsEnvelopes Appendix C Host Computer Interface Parallel Interface Interface Signals Table C . Parallel Connector Pin AssignmentsPage On-Line Select Pin Paper Empty PError PinError* nFault Pin Auto-Feed nAutoFd Pin Select In NSelectIn Pin Power Ready PinAuxiliary output 1 Pin Serial RS-232C/RS-422A Interface Option Interface SignalsTable C . RS-232C Signal Pin Assignments RS-232C interface RXD Receive Data Pin SG Signal Ground PinTXD Transmit Data Pin RTS Request To Send Pin Table C.3. RS-422A Signal Pin Assignments RS-422A interface RDB Receive Data Pin RDA Receive Data Inverted Pin Overview of Signals RS-422ASerial Connector SDB Send Data Pin SDA Send Data Inverted Pin H2 Data bits RS-232C/RS-422A ProtocolH1 Baud rate H3 Stop bits H6 Buffer nearly-full threshold H4 ParityH5 Protocol logic H7 Buffer nearly-empty threshold Prescribe Frpo D0 command H8 Received-data buffer size RS-232C Cable Connection Preparing an RS-232C Cable Connecting the Printer to the Computer Cmode LPT1=COM1 Appendix D Indicators Ready On line WaitingOff line Receiving data Selecting paper size Processing dataAdding paper Sleeping Top cover open Paper jamMemory overflow Toner status Call-service person errors ˜˜˜˜˜˜˜˜˜ Lit ˜˜˜˜˜˜˜˜˜ ˜ Off Controller system error F3 error Index MRU