Manuals / Kyocera / Computer Equipment / Printer

Kyocera FS-600 manual Auxiliary output 1 Pin, Power Ready Pin, Select In NSelectIn Pin

Models: FS-600

1 144

Download 144 pages 27.62 Kb

Page 126

Parallel Interface

Auxiliary output 1 (Pin 33)

This signal line is not used.

Power Ready (Pin 35)

This signal is high when the printer’s power is on.

Select In [NSelectIn] (Pin 36)

This signal is used in some versions of the Centronics interface to enable the computer to force the printer on-line. In high-speed mode, it is used as an interrupt.

C-6

Image 126

Kyocera FS-600 manual Auxiliary output 1 Pin, Power Ready Pin, Select In NSelectIn Pin

Contents

Italiano Regarding Tradenames Introduction Iii Typeface Trademark Acknowledgement FCC statement Conforming to the Class B limits Interface connectors Safety informationViii Ozone concentration Cdrh regulationsImportant Safeguards Canadian Department of Communications compliance statement ISOCE Marking Directive According to Council Directive 89/336/EEC and 73/23/EECXiii Declaration of Conformity AustraliaXiv Prolonged Non-use DisclaimerProlonged Non-Use and Moving the Printer Moving the PrinterXvi Long life modules IntroductionSuperb print quality Environmentally benign waste partsAutomatic rotation of fonts and graphics Wide variety of internal symbol setsNew printer control language, Prescribe IIe Simple Network Management Protocol Snmp complianceOptions Contents Xxi Chapter Installing Printer Basic requirements Environmental Requirements of the Page PrinterPlaces to Avoid ∙ Near the computerFrequency ∙ Level and well supportedVoltage Current capacityPower Supply Grounding Surrounding spaceBasic handling precautions Unpacking and InspectionList of packaged contents Moving the Printer Names of Parts Interior View Setup and Connections Install the printer on the paper feeder. Option Remove the process unit protective cover Shake four or five times Install the toner container Close the top cover Add paper Load Limit Close the cassette cover Open the face-up output tray when the tray is being used Open the paper stopper on the face-down trayConnect the printer to the computer Parallel Interface Connection Attach the power cord Be sure the printers power switch is turned offBe sure to connect the ground wire of the printer to ground Test the printer Control PanelTest the interface with the computer Echo !R! Stat Exit PRNInstall the printer driver Installing the Page Printer Setup and Connections Installing Under Windows3.1 Setup and Connections Installing the Page Printer Expanding Memory Precautions on the Handling of Extended Simm Description given below is intended for service personnelInstalling Simm Screws Pull the main circuit board all the way out of the printer Catch Socket Expanding Memory Testing Extended Memory Chapter Operating Printer Control Panel Indicators Indicators on the Control PanelControl Keys Functions of the control keys are given in the table belowKIR 2 Level KIR Level Ecoprint mode Manual Paper Feeding Sub-Tray Feeding Envelopes Overhead Projection OHP FilmAuto Manual Feeding Returning the Manual Feed Tray Fonts Fonts Scalable Fonts List of FontsBitmap Fonts Option FontsResident Scalable Fonts Resident Scalable Fonts Kpdl Fonts Kpdl Fonts Chapter Maintenance Toner Container Replacement Toner Container Replacement IntervalToner Kit to be Used Maintenance Replenishing Toner Cap Carefully remove the protective seal Toner Container Grooves Toner Container Replacement Cleaning Printer InteriorCleaning Maintenance Chapter Troubleshooting General Guide Press the on LINE/STATUS keySee Appendix C Print Quality Problems On next Chapter Commands. If the problem occurs only with a specific file or Indicators Maintenance IndicationsOpen the printer and correct the paper jam. See Indicators Error Indications Correcting a Paper Jam Jam at the Face-down and Face-up TraysPaper Cassette Paper Feeder Option Paper Feeder’s Cassette Jam Inside the Printer Troubleshooting Appendix a Printer Specifications Printer Specifications Page Appendix B Paper Selection General Guidelines Usable PaperPaper Specifications Paper SpecificationsSelecting the Right Paper Condition of the PaperComposition Paper Size SmoothnessBasis Weight Moisture ContentThickness Stiffness Paper GrainOther Paper Properties CurlPackaging Electrostatic propertiesQuality control Specially treated paperSpecial Paper OHP Film Specifications Colored PaperPreprinted Paper Overhead Projection OHP Film Postcards EnvelopesLabels Appendix C Host Computer Interface Parallel Interface Interface Signals Table C . Parallel Connector Pin AssignmentsPage On-Line Select Pin Paper Empty PError PinError* nFault Pin Auto-Feed nAutoFd PinPower Ready Pin Auxiliary output 1 PinSelect In NSelectIn Pin Serial RS-232C/RS-422A Interface Option Interface SignalsTable C . RS-232C Signal Pin Assignments RS-232C interfaceRXD Receive Data Pin SG Signal Ground PinTXD Transmit Data Pin RTS Request To Send PinTable C.3. RS-422A Signal Pin Assignments RS-422A interfaceRDB Receive Data Pin RDA Receive Data Inverted Pin Overview of Signals RS-422ASerial Connector SDB Send Data Pin SDA Send Data Inverted PinH2 Data bits RS-232C/RS-422A ProtocolH1 Baud rate H3 Stop bitsH6 Buffer nearly-full threshold H4 ParityH5 Protocol logic H7 Buffer nearly-empty thresholdPrescribe Frpo D0 command H8 Received-data buffer sizeRS-232C Cable Connection Preparing an RS-232C CableConnecting the Printer to the Computer Cmode LPT1=COM1 Appendix D Indicators Ready On line WaitingOff line Receiving dataSelecting paper size Processing dataAdding paper SleepingTop cover open Paper jamMemory overflow Toner statusCall-service person errors ˜˜˜˜˜˜˜˜˜ Lit ˜˜˜˜˜˜˜˜˜ ˜ OffController system error F3 error Index MRU