45
29.9"
36.9"
TOP VIEW
SEE HEIGHT
TABLE
AFRONT VIEW
.625" DIA x 2 |
| 17.48" | ||||||
| ||||||||
|
|
| TYP. | |||||
TYP. |
|
|
| |||||
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
2.47"
TYP.
29.44"
TYP.
NUT
JAM NUT
FOOT DETAIL A
NUT
FOOT DETAIL B
2.47"
TYP
MOUNTING PLATE
ALIGN FOOT PARALLEL TO
MOUNTING PLATE AS SHOWN
INSTALLATION NOTES:
1.CHECK ALL HARDWARE FOR PROPER TORQUE PRIOR TO INSTALLATION.
2.INSTALL REAR LOWER STS2 BRACKET TO THE FLOOR STAND USING EXISTING HOLES WITH BENT FLANGE FACING THE FRONT OF THE FLOOR STAND (FIG. 3 AND FIG 4, DWG PS215001). USE
3.LOOSEN THE STS2 ADJUSTABLE LEVELER FEET NUTS (SEE DETAIL C; DWG PS215001). INSTALL REAR UPPER STS2 BRACKET USING EXISTING HOLES ON UNDERSIDE OF THE STS2 WITH TABS FACING OUT
(FIG 1 AND FIG 2, PS215001). INSTALL FRONT UPPER STS2 BRACKET USING EXISTING HOLES ON UNDERSIDE OF THE STS2 WITH BENT FLANGE FACING TO THE FRONT. (FIG.1 AND FIG 2, PS215001). USE
4.FLOOR STAND CAN BE MOUNTED NEXT TO A WALL IF NEEDED, REAR ACCESS NOT REQUIRED. INSTALL FLOOR STAND WITH FEET ORIENTATED AS SHOWN IN (BOTTOM VIEW; DWG PS215000).
TO ADJUST VERTICAL HEIGHT OF FLOOR STAND FEET, LOOSEN, ADJUST AND TIGHTEN THE NUTS AND JAM NUT SHOWN IN (FOOT DETAIL A & B; ON DWG PS215000). FLOOR STAND MUST BE LEVEL AND ALL FEET MUST BE TOUCHING THE FLOOR. ATTACH FLOOR STAND FEET USING 1/2" X 4" RED HEAD TRUBOLTS EXPANSION ANCHORS (FEILD SUPPLIED) (2) PER FOOT.
5.ROLL THE STS2 ONTO THE FLOOR STAND SO THAT THE TABS ON THE (REAR UPPER STS2 BRACKET) FIT INTO THE SLOTS ON THE (REAR LOWER STS2 BRACKET). TABS TO EXTEND AT LEAST 1/2" THROUGH FLOOR STAND BRACKET (FIG. 2, DWG PS215002).
6.INSTALL THE LOWER FRONT BRACKETS (FIG 1, DETAIL A; DWG PS215002). ATTACH BRACKET TO STS2 USING
FLAT WASHER AND TORQUE TO 53
B | HARDWARE TORQUE CHART | |
|
|
|
| 1.0" NUT | 320 FT - LBS |
| M8 - 1.25 | 16FT - LBS |
|
|
|
| M10 - 1.5 | 31 FT - LBS |
|
|
|
| M12 - 1.75 | 53 FT |
|
|
|
HEIGHT TABLE
P/N OF FLOOR STAND: | HEIGHT | HEIGHT MAX: | HEIGHT MIN: |
523401G1 | 18.0" | 19.25" | 16.75" |
523402G1 | 24.0" | 25.25" | 22.75" |
523403G1 | 30.0" | 31.25" | 28.75" |
523404G1 | 36.0" | 37.25" | 34.75" |
Figure 33 Installation drawing, seismic floor stand 100-250A
6" TYP. | BOTTOM VIEW |
ISOMETRIC VIEW 250A FLOOR STAND
INSTALLATION DRAWING FOR SEISMIC FLOOR STAND
PS215000 REV. NO. 0
Installation Drawings
