Oven Temperature, Ohms, Switch, Display, Set | Lincoln 1100 Series

OVEN TEMPERATURE

FOR DISPLAYS WITH THERMISTOR PROBE ONLY

BOTTOM OF TIME TEMP DISPLAY

test leads here

reading should be 26 ± .5 ohms if not, adjust. pot. range 0-34 ohms

TIME CALIBRATION

1.Be sure dip switch settings are proper.

2.Turn power on.

3.Turn conveyor on.

4.Place an object on the conveyor belt and time with a stopwatch, the elapsed time for the object to travel through the oven (leading edge in to leading edge out).

5.Push in and hold the set button. (Discontinued on newer models)

6.Adjust time pot. (rear of display) so display agrees with your stop watch time.

7.Seal pot. with Glyptol or nail polish.

THERMISTOR PROBE REPLACEMENT

1.Shut off power at the main breaker.

2.Remove conveyor and fingers from oven.

3.Remove control compartment covers.

4.Disconnect the 2 yellow thermistor leads from terminals 9 and 10 on the rear of the time/temp. display.

5.Remove the sensing bulb of the thermistor probe from its wire form holder located at right inside rear of the oven.

6.Install in reverse order.

NOTE: Be sure that the spring holder is holding the sensor bulb firmly. If the sensor is not	held firmly,
compress the wire form slightly to increase pressure.
To test the thermistor probe, refer to the following chart and instructions:

OVEN TEMPERATURE

	300°F	325°F	350°F	400°F	425°F	450°F	500°F	550°F
OHMS	182	138	102	62	48	38	24	16

1.Place test pyrometer thermocouple and preheat oven as specified under temperature calibration on Page D15.

2.Disconnect the thermistor probe from terminals 9 and 10 and measure the resistance across the 2 yellow leads

3.Refer to the above chart to determine if probe is producing the proper resistance. EXAMPLE: The probe resistance at 500°F(260°C) should be 24 ohms.

SWITCH, DISPLAY, SET

1 Shut off power at main breaker.

62	Impinger II - 1100 Series Service Manual - International

Image 62

Lincoln 1100 Series service manual Oven Temperature, Ohms, Switch, Display, Set

Contents

MODEL 1100 SERIES SERVICE MANUALIMPINGER CONVEYOR OVENS INTERNATIONAL TABLE OF CONTENTS SEQUENCE OF OPERATIONS 1104 thru the display into a temperature reading SEQUENCE OF OPERATION 1134 - 1135 - 1136 - S/N 2011383 and above SEQUENCE OF OPERATIONS 2011383 and above SEQUENCE OF OPERATIONS 1152 thru intervals to maintain desired temperature temperature reading by the display into a temperature reading SCHEMATIC SCHEMATIC SCHEMATIC 1134, 1135, 1150, S/N 2011383 AND BELOW SCHEMATIC 1134, 1135 S/N 2011383 AND ABOVE SCHEMATIC 1150 S/N 2011383 AND ABOVE SCHEMATIC 1136, S/N 2011383 AND BELOW SCHEMATIC 1136, S/N 2011383 AND ABOVE SCHEMATIC 1151 S/N 2011383 AND BELOW SCHEMATIC 1151 S/N 2011383 AND ABOVE SCHEMATIC1152 THRU 1158 S/N 2011383 AND BELOW SCHEMATIC1152 THRU 1158 S/N 2011383 AND ABOVE SCHEMATIC1152 AND 1153 S/N 2011821 AND ABOVE SCHEMATIC 1154 THRU 1158 S/N 2011821 AND ABOVE TROUBLE SHOOTING GUIDE GAS OVENS MODELS 1152 - 1153 - 1154 - 1155 - 1156 No main fan cool down present on one side only, replace switch Burner Switchswitch. If switch is closed and voltage Gas Pressure Switch Check for proper line voltage to Flame Sensor Power Supply Ignition ControlFlame will not stay on Pilot lamp is on, but then the problem is usually with thetemperature Power Supply improper adjustment. Also check for wornbearings. TheInstallation and Operations Manual Check power supply at the DC DC Gearmotor switch for 15 seconds, or if display stays on surge in the incoming power lines. To eliminatethis condition remove power from the time/temp required. This should eliminate the problem. If TROUBLE SHOOTING GUIDE ELECTRIC OVENS This normally open switch should close when the Switch, HeatAir Pressure Switch adjustment knob to maximum temperature position as follows MODEL Main fan runs after for proper readings. If these readings WITH POWER OFF: To check resistance of themaintenance. Also, most of the problems are not achieved, replace thermocouple Conveyor will not run TROUBLESHOOTING GUIDE ELECTRIC OVEN MODEL 1151 200 VAC THREE PHASE 60 HZ Relay, Main Fan REFER TO PAGE REFER TO PAGE REFER TO PAGE Mercury Contactor Heater ElementsConveyor will not run S/N 2011383 and above REFER TO PAGE REFER TO PAGE 43 STEPPER MOTOR DRIVE Conveyor will not run red wire and 1 white wire 12 VAC Power Supplyyellow wires, thermo Thermocouple Probe Power Supply experienced, such as a rolling of REMOVAL, INSTALLATION, AND ADJUSTMENT IMPINGER II CONVEYOR OVEN RELAY, DPST 1.Shut off power at main breaker MOTOR, BURNER BLOWER This is part of the burner blower motor assemblyTO REMOVE THE BLOWER WHEEL FOR PERIODIC CLEANING TO REMOVE BLOWER MOTOR AIR PRESSURE SWITCH Page Page 5.Loosen pipe union in piping assembly 1.Shut off power at the main breakerSOLENOID VALVE 1.Shut off power at main breaker HEATING ELEMENTS 1.Shut off power at main breaker IGNITION CONTROL 1.Shut off power at main breaker 4.Remove control compartment covers ORIFICE, MAIN BURNER2.Shut off gas at main line to the oven 5.Loosen 4 nuts holding manifold to burner cap LAMP, PILOT BURNER LENS, PILOT LAMP 7.To adjust optical encoder OPTICAL ENCODER ASSEMBLY1.Remove gearmotor assembly see “GEARMOTOR” Above TACH. GENERATOR 1.Turn off power at main breaker D C MOTOR CONTROL BOARD 5.Reverse wires fastened to terminals T1 and T2 1.Turn off power and remove conveyor4.Reverse wires fastened to terminals A+ and A 1.Turn off power 2.Remove conveyor TRANSFORMER, TIME/TEMP. DISPLAY MODEL 1100 SERIES OVENS OHMS SWITCH, DISPLAY, SETOVEN TEMPERATURE SWITCH, ON/OFF TRANSFORMER, STEP DOWN/120 VAC DIP SWITCHES FOR 50 SEC. TO 30 MIN. TIMES maximum speed potrefer HALL EFFECT SENSOR - REPLACEMENT AIR PRESSURE SWITCH, BURNER OR OVEN CAVITY 8.Remove top control compartment brace BURNER ALARM - REPLACEMENT4.Remove conveyor gear motor 10.Assemble in reverse order DESCRIPTION GENERAL –1100SERIESLETTER GENERAL 1100 SERIES BLOW UP 1136,1150,1151,1160 Thru1163 Page LETTER CONTROL COMPARTMENT - FRONTMODELS 1152 THRU DESCRIPTION CONTROL COMPARTMENT – FRONT 1152-1158BLOW UP DESCRIPTION CONTROL COMPARTMENT – REARLETTER CONTROL COMPARTMENT - REAR BLOW UP MODELS AND ABOVE MODELS 1160-1163S/N 2011978 AND ABOVE CONTROL COMPARTMENT – REAR BLOW UPMODELS 1130-1136,1150,1151S/N 2011383 AND ABOVE DESCRIPTION CONTROL COMPARTMENT – REARLETTER Page LETTER CONTROL COMPARTMENT – REARMODELS 1152 THRU 1158 S/N 2011821 AND ABOVE DESCRIPTIONPage OVEN BACK ASSEMBLY – 1100 SERIES OVEN BACK ASSEMBLY – 1100 SERIES BLOW UP GEARMOTOR ASSEMBLY – 1100 SERIES GEARMOTOR ASSEMBLY – 1100 SERIES BLOW UP CONVEYOR/DOOR – 1100 SERIES CONVEYOR/DOOR – 1100 SERIES BLOW UP This page intentionally left blank This page intentionally left blank