Setting up the LCD Hinge | Matsushita CF-19FHGAX specification

■Line Processing of Antenna Cable

Safety Working

CAUTION

S1:Insulation S2:Pinching Cables S3:Sharp Edge

S4:Part No. Check S5:Others

Note: Avoid any stress on the solder.

Match to the edge of Cabinet

S2

Details of "B"

Avoid running over the rib, etc..

Match to the edge of Cabinet

	A	B
	A
Screw		Screw
EVDO/EDGE Antenna

S2	Cable Cushion Attachment Method
	(3 Places)

Details of "A"	Bundle and wind 3	Insert it between the wall and the rib after attaching.		LAN Main
	antenna cables.
				/BT ANT
		Cable Cushion	Avoid running over the rib, etc..

Avoid running over		Details of "D"	S2
the rib, etc..		Details of "D"
		Insert it between the pins.	Screw
		Insert it between the pins.	Match to the
Screw			Match to the
Screw		Hook it.	edge of Cabinet
			edge of Cabinet
Put the Cable on each hook
Put the Cable on each hook
Screw			Screw
LAN-AUX ANT			EVDO-AUX
Screw			Screw
Match to the edge of Cabinet			Screw
S2	C		D

Details of "D"

Avoid running over the rib, etc..

Put the Cable on each hook		Tape Pen Holder
	Cable Cushion
		Cable Cushion

Put the center of Cushion between the ribs.

Match to the edge of Cabinet

Put the Cable on each hook

Cable Cushion

9.2.4.Setting up the LCD Hinge

1.Wind the Cable coming out of the LCD Unit counterclock- wise to the LCD Hinge.

2.Set the Lock Plate and the Hinge Top Cover, and rotate the LCD Hinge to turn the Display Unit to front

3.Put the LCD Cable and the Antenna Cable in the Cable Holder.

4.Fit another Cable Holder and clamp the Cable Holders in the LCD Hinge.

5.Fix the LCD Hinge using the 2 Screws <N17> and the 2 Cable Holder Plates.

Screws <N17 > : DXYN3+J8FNL

Cable	<N17>
Holder		<N17>	Cable
Plate
			Holder
LCD			Plate
Hinge			Cable
			Holder
Cable Holder		LCD Cable
		Holder
Plate		Sheet

Cable

Holder

37 / 90

Image 37

Matsushita CF-19FHGAX service manual Setting up the LCD Hinge, Line Processing of Antenna Cable

Contents

Model No. CF-19FHGAXxM For U.K How to replace the fuse Laser Safety Information Safety Precautions Precautions Battery Pack Contents Main Specifications Specifications BluetoothTM Only for model with Bluetooth Wireless LAN Only for model with wireless LAN Names and Functions of Parts LAN Port SD Memory Card Indicator Blinking During access Host PCI Bridge InternalSigmatel AC-link Diagnosis Procedure Check Bios operation Acng Adaptor/Battery Output voltage Power lamp CheckTroubleNO symptoms on some Inverter board LCD back Light lighting Table of errors classified by beep sounds Error Diagnosis by Checking Beep Signal SoundOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS Screen TouchPanel 1394 Preparation Removing the Battery Pack and HDD PackRemoving the Touch Pad and Key- board Removing the Rear Cabinet Removing the Dimm Lid Assíy Removing the DU Lid Unit Removing the Hsdpa PCB and Bluetooth PCBRemoving the Audio PCB HDD Removing the I/O PCB Assy Removing the Power SW PCBRemoving the left LED and right Removing the Display unit Removing Pad PCB and SW PCB Removing the LCD Hinge Removing the LCD Rear CaseRemoving Inverter PCB and LCD Unit USB Removing the Each Cover Sheet Setting up the Inverter Assy and LCD UnitPCB Spacer Assembly of Inverter PCB LCD Side Cushion E Inverter AssyCushion High LCD Side Cushion E TS PWB LCD Side Cushion Voltage Label Assembly of Inverter PCB Application Model Digitizer Model Touch Screen Assy LaminateProtect Sheet Spacer Assembly of Glass Applicable Model Digitizer Model Line Processing of Antenna Cable Setting up the LCD Hinge Cable Hold Plate Assembly of LCD HingeScrew LCD Hinge S2 Fit Holders as shown in figure Until you hear the click Cable Guide HInge Cable Holder LCD Front Assy Magnet Assy 0 0.5mm Magnet Tape Assembly of LCD Front Case Marking line Assembly of LCD Rear Case Applicable Model Digitizer Model5mm Marking line Attach it between marking lines Antenna Cover Assembly of Tablet Latch Cover and Antenna CoverAntenna Cushion L Screw Antenna Cover Setting the Display Unit Screw Screw Assembly of Display Unit Setting the Pad PCB and SW PCB Assembly of the Pad PCB and SW PCB Setting the left LED PCB and right LED PCBPutting of the TP Bottom Tape Assembly of the left LED PCB and right LED PCB Setting the Power SW PCBAssembly of the Power SW PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit ScrewScrew Screw HDD Connector Guide Thermal Rubber SD PCB AssyDimm Holder Assy RF SW Knob Dimm Holder Screw Battery FPC Assy Setting the Audio PCB Setting the Hsdpa PCB and Bluetooth PCB Cable Process 1/3 Line Processing of Antenna Cable of Main Unit Step Cable StepCable Process 3/3 Step Cable Holder Cushion Assembling the DU Lid Unit Setting the Rear Cabinet Dimm Thermal Sheet Setting the Dimm Lid AssyBottom Rubber Tape Bottom Case Assy Setting the Touch Pad and Keyboard Putting of the Sheet Putting of the KBD Tape Putting of the Palm Rest AssyIntel Label Windows Logo Label Energy Star Label Setting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Main Block Unit Replacement Parts List Packing Material AccessoriesMechanical Parts DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller