■Assembly of Inverter PCB (Applicable Model : Touch Screen Model)
Inverter Ass'y
Confirm the direction of the Inverter board when attaching.
|
|
|
|
|
|
|
|
|
|
| Avoid any stress on the Cable when |
|
|
|
|
|
|
|
|
|
|
| connecting the CCFL Cable. |
|
|
|
|
|
|
|
|
|
|
| Hold the Connector part when |
|
|
| Attach it to the Connector and FPC. |
| connecting/disconnecting. | ||||||
|
|
| LCD Side Cushion E | ||||||||
|
|
|
|
|
|
|
|
|
| ||
Insert it between the ribs. |
|
| 12 |
|
| Connector | Insert it between the ribs. | ||||
|
|
|
|
|
| PWB | |||||
|
| FPC |
|
| (Fit to the Cabinet.) | ||||||
|
|
|
| ||||||||
(Fit to the Cabinet.) |
|
|
|
| |||||||
|
|
|
|
|
|
|
|
| Cushion High | ||
LCD Side Cushion E |
|
|
|
|
|
|
|
|
| ||
| TS PWB LCD Side Cushion | F |
| Voltage Label | |||||||
Insulation | Parts | Insulation Parts | Connect |
|
| Insert it between the ribs. | |||||
|
|
|
|
|
|
|
| (Fit to the Cabinet.) | 0 3mm | ||
|
|
|
|
|
|
|
|
|
|
| |
30 | 35mm | Inverter Mil Sheet | ||
|
| |||
|
|
|
|
|
|
|
|
|
|
Inverter Ass'y | The gap side is front. | |||
Details of cable
LCD Ass'y
Details of "A"
Ensure the edge of the conductive fabric is not frayed.
1 2 A mm
S5
| Inverter Ass'y |
| |
0 0.5mm | Connect the Cable to the | Tape | |
Sub material: Pet Tape 1 | left and right Connectors. |
| |
| Attach the Inverter Ass'y in the | ||
Avoid any stress on the Cable |
| middle of right and left. | |
| Attach the surplus of the right and left sides on the | ||
when connecting it. |
| ||
| Back Dumper as shown below and overlap on the | ||
Hold the Connector part when |
| ||
| CCFL Cable. Attach the Pet Sheet over the Core. | ||
connecting/disconnecting. |
| ||
| Note for attaching Conductive Tape | ||
LCD Cable TS | |||
|
|
| Conductive Tape |
Wind round the LCD Cable |
|
| Inverter Ass'y |
a few times and attach it. |
|
| |
Sield Sheet | Fix the two Cables | LCD Back Dumper | |
Avoid getting under the Sheet. | and connector. |
| |
Insulation Parts | 0 | 4mm |
Insulation Parts |
|
|
| 6 | 2mm from the |
Connect | branch point | |
|
| |
Attach coming over the end of steel plate by 1 to 2 mm.
Avoid running over the rib
0 1mm
S2
Avoid any stress on the Tab part of the | Conductive Tape |
| |
LCD Module because the line comes off. |
|
Wrap of Antenna Cable | Wrap over the Antenna Cable |
Cushion and the Cable. | |
Cushion E |
|
Safety Working
CAUTION | S1:Insulation S2:Pinching Cables S3:Sharp Edge |
| S4:Part No. Check S5:Others |
|
|
33 / 90
