9.2.Reassembly Instructions
9.2.1.Attention when
ïPlease execute writing BIOS ID when you exchange the Main Board.
ïParts (Sheet and rubber) etc. related various the Conductive Cloth and Heat Spreader cannot be recycled. Use new parts.
9.2.2.Setting up the Inverter Ass'y and LCD UNIT
1. | Set the LCD UNIT to the LCD Front Cabinet/TS Panel. |
|
|
2. | Set the TS PCB on the LCD Back Damper, and connect |
| Tape |
| the 2 Cables to the Connectors (CN900 and CN901). |
|
|
3. | Set the Inverter PCB to the LCD Back Damper, and con- |
| Connector |
| nect the 2 Cables to the Connectors. |
| |
| Inverter Case | Inverter PCB | |
|
|
Connector
Connector
(CN901)
TS PCB
Connector (CN900)
LCD Unit
■Assembly of LCD Back Damper (Applicable Model : Touch Screen Model)
Detail of "B"
0
1mm
Pass the Cable 0 0.5mm under the protrusion.
Detail of "C"
0
1mm
Pass the Cable 
through the space.1
1.5mm
Detail of "D"
0 | 1mm |
|
| 0 | 0.5mm |
Pass the Cable |
| |
under the protrusion. |
| |
| LCD Back Cushion S | LCD Back Cushion L | LCD Back Cushion S |
Note: Apply the load to attach. 20 to 30N (2.0 to 3.0 Kgf) | B | C | D |
Order of fixing | 33 | 35mm |
|
|
|
|
|
|
|
|
| ||
| Detail of "A" |
|
|
|
|
|
| 2 4mm | A |
| Remove the Release Paper on |
| |
|
|
|
| |||
|
|
| Holder Sheet | the back side and attach it. |
|
|
|
|
| Lengthwise : Match to the LCD Frame. | Holder Sheet | ||
|
|
|
| Crosswise : Match to the middle line. | ||
|
|
|
|
| ||
| LCD Side Cushion A |
|
|
|
| |
| Attach to the side surface if the Frame. |
|
|
|
| |
| (Match to the end of the Frame within | Match both Holder Sheet and LCD | Match both Holder Sheet and LCD | |||
| 0 to 0.5 mm at the far side.) |
| Back Cushion S to the right edge | |||
|
| Back Cushion S to the right edge | ||||
|
|
| of the frame. (0 to 0.5 mm) |
| ||
|
|
|
| of the frame. (0 to 0.5 mm) | ||
|
|
|
|
| ||
| LCD PWB Spacer Ass'y |
|
|
|
| |
| Insert this between LCD |
|
|
|
| |
| PCB & LCD Frame. |
|
|
|
| |
| Screw 1 |
|
|
|
| |
| Screw the board and |
|
|
|
| |
| the Spacer together. |
|
|
|
| |
0
0.5mm
Screw 2
Screw the board and the Spacer together.
|
|
|
|
|
|
| LCD Side Cushion C | LCD Side Cushion D | LCD Side Cushion C |
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
| |
LCD PWB SPACER ASSY |
|
|
|
| 0 0.5mm |
|
| ||
|
| Spacer | Sheet | 0.5mm | 0.5mm | ||||
Spacer | Sheet |
|
|
| |||||
LCD | PCB Spacer |
|
|
| |||||
|
|
|
| ||||||
|
|
|
|
| |||||
|
|
|
| ||||||
|
|
|
| Asymmetric Shape | 0.5mm |
| 0.5mm | ||
|
|
|
|
| |||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
| 0.5mm | |
|
|
|
|
|
|
|
|
| |
31 / 90
