Hdd | Matsushita CF-19FHGAX guide

4.Fix the Modem PCB using the 2 Screws <N19>.

5.Fix the Wireless Module using the 2 Screws <N19>.

6.Fix the DIMM Holder using the 2 Screws <N19>.

7.Attach the Cable to the Connector (CN3) and attach the Coin Battery.

8.Fix the SD PCB Ass'y using the 3 Screws <N19>.

9.Attach the Cable to the Connector (CN21).

10.Hook the Flex Cable on the DIMM Holder, and turn 90 degrees.

11.Fix the BAT FPC Ass'y using the 2 Screws <N9>.

12.Connect the cable to the Connector. (CN15)

13.Fix the HDD Connector Guide using the 2 Screws <N8>.

DIMM Holder	Wireless Module		<N19>
DIMM Holder	Wireless Module
<N19>		<N19>	<N19>
<N19>		<N19>
<N19>

Modem PCB

Connector(CN3)

Coin Battery

<N8>

<N8>

HDD

Connector Guide <N19>

<N19>

Connector (CN882)

<N9>

<N9>

SD PCB Ass'y

BAT FPC Ass'y

Connector(CN15)

49 / 90

Image 49

Matsushita CF-19FHGAX service manual Hdd

Contents

Model No. CF-19FHGAXxM For U.K How to replace the fuse Laser Safety Information Safety Precautions Precautions Battery Pack Contents Main Specifications Specifications BluetoothTM Only for model with Bluetooth Wireless LAN Only for model with wireless LAN Names and Functions of Parts LAN Port SD Memory Card Indicator Blinking During access Host PCI Bridge InternalSigmatel AC-link Diagnosis Procedure Check Bios operation Acng Adaptor/Battery Output voltage Power lamp CheckTroubleNO symptoms on some Inverter board LCD back Light lighting Table of errors classified by beep sounds Error Diagnosis by Checking Beep Signal SoundOutline of Post Stuck key 02F0 CPU ID Self Diagnosis Test Operation of PC-Diagnostic Utility Selection of tested device Test Item and Division of trouble GPS Screen TouchPanel 1394 Preparation Removing the Battery Pack and HDD PackRemoving the Touch Pad and Key- board Removing the Rear Cabinet Removing the Dimm Lid Assíy Removing the DU Lid Unit Removing the Hsdpa PCB and Bluetooth PCBRemoving the Audio PCB HDD Removing the I/O PCB Assy Removing the Power SW PCBRemoving the left LED and right Removing the Display unit Removing Pad PCB and SW PCB Removing the LCD Hinge Removing the LCD Rear CaseRemoving Inverter PCB and LCD Unit USB Removing the Each Cover Sheet Setting up the Inverter Assy and LCD UnitPCB Spacer Assembly of Inverter PCB LCD Side Cushion E Inverter AssyCushion High LCD Side Cushion E TS PWB LCD Side Cushion Voltage Label Assembly of Inverter PCB Application Model Digitizer Model Touch Screen Assy LaminateProtect Sheet Spacer Assembly of Glass Applicable Model Digitizer Model Line Processing of Antenna Cable Setting up the LCD Hinge Cable Hold Plate Assembly of LCD HingeScrew LCD Hinge S2 Fit Holders as shown in figure Until you hear the click Cable Guide HInge Cable Holder LCD Front Assy Magnet Assy 0 0.5mm Magnet Tape Assembly of LCD Front Case Marking line Assembly of LCD Rear Case Applicable Model Digitizer Model5mm Marking line Attach it between marking lines Antenna Cover Assembly of Tablet Latch Cover and Antenna CoverAntenna Cushion L Screw Antenna Cover Setting the Display Unit Screw Screw Assembly of Display Unit Setting the Pad PCB and SW PCB Assembly of the Pad PCB and SW PCB Setting the left LED PCB and right LED PCBPutting of the TP Bottom Tape Assembly of the left LED PCB and right LED PCB Setting the Power SW PCBAssembly of the Power SW PCB Setting the I/O PCB Assy HDD N3 DU PCB N3 N9 N9 Antenna PCB Plate White cable Black cable Assembly of Main PCB Page Assembly of Main Unit ScrewScrew Screw HDD Connector Guide Thermal Rubber SD PCB AssyDimm Holder Assy RF SW Knob Dimm Holder Screw Battery FPC Assy Setting the Audio PCB Setting the Hsdpa PCB and Bluetooth PCB Cable Process 1/3 Line Processing of Antenna Cable of Main Unit Step Cable StepCable Process 3/3 Step Cable Holder Cushion Assembling the DU Lid Unit Setting the Rear Cabinet Dimm Thermal Sheet Setting the Dimm Lid AssyBottom Rubber Tape Bottom Case Assy Setting the Touch Pad and Keyboard Putting of the Sheet Putting of the KBD Tape Putting of the Palm Rest AssyIntel Label Windows Logo Label Energy Star Label Setting the Battery Pack and the HDD Pack Assembly of the HDD Assy Assembling the Each Cover Exploded View K1610 K12-15-10 K12-15-4 K12-15-5 K12-15-3 K51 K14-8 + 0.2kgf cm K84 K61 K78 K68 K69 K11-1-3 N15 Main Block Unit Replacement Parts List Packing Material AccessoriesMechanical Parts DFHR3563YA LCD Rear Cushion C DFUN0069XA Latch Knob Spring DFMC0877YA Inverter Case DFHG429YA IO DC Tube Description QTY EEFCX0G151R Thermistor IC, Micon FET ERJ2GEJ471X ERJ2GEJ684X IO PCB SW PCB Ppower Swpcb IC, Touchpanel Controller