Troubleshooting Fehlerbehebung | Mitsubishi Electronics PKFY-PVAM-A

E5. Troubleshooting

D5. Fehlerbehebung

Before you ask for repair service, check the following points:

State of Machine	Troubleshooting

It does not run.	Press the [ON/OFF] button after power restoration.

Air flows out but it does not cool enough or heat	Check the set temperature.
enough.	Clean up the filter.

Cool air or warm air does not come out.	Wait for a while.
	The restart-preventing circuit is in operation for 3 minutes.

	Wait for a while.
	Indoor unit operation was started anew during the heating and defrosting operation.

The sound of the exhaust and rotation of the motor	Wait for 3 minutes.
can still be heard after stop of running.	The machine stops after running a drain-up mechanism for 3 minutes when air-cooling operation is stopped.

The following symptoms are not air conditioner failures:

•The air blown out from the air conditioner can sometimes give off odors. This is due to cigarette smoke contained in the air of the room, the smell of cosmetics, the walls, furniture, etc., absorbed in the air conditioner.

•A hissing noise can be heard immediately after the air conditioner is started or stopped. This is the sound of the refrigerant flowing inside the air conditioner. The problem is insignificant.

•The air conditioner sometimes snaps or clicks at the beginning or end of cooling/heating operation. This is the sound of friction on the front panel and other sections due to inflation and contraction caused by temperature change. The problem is insignificant.

Range of application

The range of working temperatures for both the indoor and outdoor units of the series Y, R2, Multi-S is as below.

Caution:

The use of your air conditioner outside the range of working temperature and humidity can result in serious failure.

5	Mode	Indoor unit		Outdoor unit
	Mode	Indoor unit
			PUHY	PURY	PUMY
			PUHY	PURY	PUMY

	Cooling	15°C-24°CWB	–5°C-43°CDB	–5°C-43°CDB	–5°C-46°CDB
	Heating	15°C-27°CDB	–15°C-15.5°CWB	–12°C-15°CWB	–12°C-15.5°CWB

Note: As an applicable humidity standard for both indoors and outdoors, we recommend use within a range of 30 - 80% relative humidity.

Bitte überprüfen Sie die folgenden Punkte, bevor Sie sich an den Kundendienst wenden.

Zustand der Klimaanlage	Behebung

Kein Betrieb	Nach Wiederherstellung der Stromversorgung die Taste [ON/OFF] drücken.

Luft wird ausgeblasen, aber es wird nicht gut ge-	Die eingestellte Temperatur überprüfen.
kühlt oder geheizt.	Den Filter reinigen.

Es wird keine kalte bzw. warme Luft ausgeblasen.	Bitte einige Zeit warten.
	Der Stromkreis zur Verhütung von Neustart innerhalb von 3 Minuten ist tätig.

	Bitte einige Zeit warten.
	Während Heizentfrostungsbetrieb ist eine neue Inneneinheit eingeschaltet worden.

Der Betrieb wird nach kurzer Zeit wieder eingestellt.	Bitte 3 Minuten warten.
	Die Maschine schaltet sich aus, nachdem sie 3 Minuten lang im Ablaßmechanismus gelaufen ist, wenn die Luftkühlung
	beendet ist.

In den folgenden Fällen handelt es sich nicht um eine Störung.

•Die aus der Klimaanlage ausgeblasene Luft kann einen Geruch haben. Der in der Raumluft enthaltene Geruch von Zigaretten, Kosmetika, Wänden, Möbeln usw. haftet in der Klimaanlage an und wird wieder ausgeblasen.

•Bei laufender oder angehaltener Klimaanlage kann das Geräusch von fließendem Kühlmittel zu hören sein. Dies stellt kein Problem dar.

•Nach Start oder Stop von Kühl- oder Heizbetrieb kann sich die Vorderplatte usw. wegen des Temperaturunterschieds hörbar verziehen. Dies stellt kein Problem dar.

Verwendungsbereich

Die Betriebstemperaturbereiche für Innen- und Außenanlagen der Baureihe Y, R2, Multi-S sind nachstehend aufgeführt.

Vorsicht:

Verwendung außerhalb des Temperatur- und Luftfeuchtigkeitsbereiches kann schwere Störungen verursachen.

Betriebsart	Inneneinheit		Außeneinheit
		PUHY	PURY	PUMY

Kühlen	15°C bis 24°CWB	–5°C bis 43°CDB	–5°C bis 43°CDB	–5°C bis 46°CDB
Heizen	15°C bis 27°CDB	–15°C bis 15,5°CWB	–12°C bis 15°CWB	–12°C bis 15,5°CWB

Hinweis: Innen- und Außeneinheiten sollten in einem Luftfeuchtigkeitsbereich von 30 bis 80% RH verwendet werden.

PKFY-PVAM-A specifications

The Mitsubishi Electronics PKFY-PVAM-A is a cutting-edge air conditioning system designed for optimal performance and energy efficiency in residential and commercial settings. This model is part of Mitsubishi's comprehensive lineup of air conditioning solutions, recognized for their reliability, technological advancements, and sustainable practices.

One of the standout features of the PKFY-PVAM-A is its advanced inverter technology. This technology enables the system to adjust the compressor speed progressively, allowing for precise temperature control while significantly reducing energy consumption. The result is a system that operates quietly, maintains consistent indoor climate conditions, and minimizes energy bills, making it an environmentally friendly choice for consumers.

In terms of design, the PKFY-PVAM-A boasts a sleek and compact unit that is easy to install and blends seamlessly with various interior designs. It is engineered for both ceiling and wall-mounted installation, providing flexibility in application for diverse spaces. Additionally, the unit features a sophisticated air distribution system that ensures uniform airflow throughout the room, enhancing comfort and air quality.

The PKFY-PVAM-A is equipped with multiple cooling and heating modes, with a wide operating temperature range that makes it suitable for various climates. This includes a powerful heating function, ensuring that the system can provide comfort even in colder months. Moreover, the unit includes a built-in hot-start function that prevents cold drafts when the heating system is activated.

For user convenience, the PKFY-PVAM-A includes a sophisticated remote control system. This allows users to operate their air conditioning unit from a distance, adjusting temperature settings or switching modes with ease. The unit is also compatible with smart home systems, enabling users to integrate it into their connected home ecosystem for enhanced control and automation.

Another noteworthy characteristic of the PKFY-PVAM-A is its low noise operation. The system is designed to minimize sound levels, ensuring a comfortable and quiet environment in both residential and commercial spaces. This feature is particularly important for settings such as offices or bedrooms, where distractions can impact productivity and comfort levels.

Overall, the Mitsubishi Electronics PKFY-PVAM-A is a versatile and efficient air conditioning solution that combines advanced technology with user-friendly features. Its inverter technology, smart controls, and sleek design make it an outstanding choice for anyone looking to enhance their indoor climate while reducing energy consumption.

Mitsubishi Electronics PKFY-PVAM-A Troubleshooting Fehlerbehebung, Range of application

Models: PKFY-PVAM-A