IP Address, Netmask, Gateway | Moxa Technologies 5400 Series

NPort 5400 Series User’s Manual		Web Console Configuration
	IP Address
	Setting	Factory Default	Necessity
	E.g., 192.168.1.1	192.168.127.254	Required
	(IP addresses of the form x.x.x.0 and
	x.x.x.255 are invalid.)

An IP address is a number assigned to a network device (such as a computer) as a permanent address on the network. Computers use the IP addressed to identify and talk to each other over the network. Choose a proper IP address which is unique and valid in your network environment.

Netmask

Setting	Factory Default	Necessity
Ex. 255.255.255.0	255.255.255.0	Required

A subnet mask represents all the network hosts at one geographic location, in one building, or on the same local area network. When a packet is sent out over the network, the NPort will use the subnet mask to check whether the desired TCP/IP host specified in the packet is on local network segment. If the address is on the same network segment as the NPort, a connection established directly from the NPort. Otherwise, the connection is established through the given default gateway.

Gateway

Setting	Factory Default	Necessity
Ex. 192.168.1.1	None	Optional

A gateway is a network gateway that acts as an entrance to another network. Usually, the computers that control traffic within the network or at the local Internet service provider are gateway nodes. The NPort needs to know the IP address of the default gateway computer in order to communicate with the hosts outside the local network environment. For correct gateway IP address information, consult the network administrator.

IP Configuration

Setting	Factory Default	Necessity
Static	Static	Required
DHCP
DHCP/BOOTP
BOOTP

ATTENTION

In Dynamic IP environments, the firmware will retry 3 times every 30 seconds until network settings are assigned by the DHCP or BOOTP server. The Timeout for each try increases from 1 second, to 3 seconds, to 5 seconds.

If the DHCP/BOOTP Server is unavailable, the firmware will use the default IP address (192.168.127.254), Netmask, and Gateway for IP settings.

5-7

Image 33

Moxa Technologies 5400 Series user manual IP Address, Netmask, Gateway, IP Configuration

Contents

Sixth Edition, March NPort 5400 Series User’s Manual Copyright Notice TrademarksDisclaimer Table of Contents Chapter IP Serial LIB Introduction Package Checklist Product FeaturesOverview Product Specifications Power Requirements Software FeaturesSerial Communication Parameters Mechanical Getting Started ‰ Panel Layout ‰ Connecting the Hardware Panel Layout NPort 5410/5450/5450INPort 5430/5430I Wiring Requirements Connecting the HardwareConnecting the Power Grounding the NPort Connecting to a Serial Device Connecting to the NetworkLED Indicators LED Name LED Color LED Function Pull high/low resistors for the RS-485 Port Adjustable Pull High/low Resistors for the RS-485 Port Initial IP Address Configuration Default IP address Factory Default IP AddressInitializing the NPort’s IP Address LCM Display Detailed Menu Options Button Name Action Inact. time Delimiter ARP NPort Administration Suite Telnet Console Page Page Choosing the Proper Operation Mode Real COM Mode TCP Server Mode TCP Client Mode UDP ModePair Connection Mode Disabled Mode Reverse Telnet Mode Web Console Configuration Opening Your Browser NPort 5400 Series User’s Manual Web Console Configuration Time Basic SettingsServer name Time zone Web/Telnet Console LCM password protectTime server Web console Network Settings Reset button protectMethod Function Definition IP Address IP ConfigurationNetmask Gateway IP Address Report Snmp Settings Setting Factory Default Necessity 4002 Optional Serial SettingsAuto report to IP Auto report to UDP port Serial Parameters Operating Settings Real COM ModeInterface Max. Connection Max ConnectionMax Connection 2 to Ignore jammed IP Setting Factory Default Necessity To 65535 ms Optional Setting Factory Default Necessity To FF None OptionalDelimiter Delimiter process Setting Factory Default Necessity To 99 min Min Optional TCP Server ModeTCP alive check time Inactivity time Allow driver control Delimiter Setting Factory Default Necessity 4001 Required TCP Client ModeCommand port Setting Factory Default Necessity 966 Optional NPort 5400 Series User’s Manual Web Console Configuration Delimiter Destination IP address 2/3/4 Destination IP addressDesignated Local Port 1/2/3/4 Connection control Connect/Disconnect Description UDP Mode Delimiter process Pair Connection Mode Pair Connection Master ModeLocal listen port Setting Factory Default Necessity To 99 min Min Required Pair Connection Slave Mode Setting Factory Default Necessity To 99 min Optional Reverse Telnet ModeSetting Factory Default Necessity 4001 Optional Means it will never disconnect Disabled Mode Accessible IP SettingsOnly one host of specific IP address can access the NPort Hosts on the specific subnet can access the NPort Auto Warning Settings Auto warning E-mail and Snmp trapMail Server Snmp Trap Server Event Type DCD changed Password changedDSR changed Mail Monitor Monitor Async-SettingsMonitor Line Monitor Async Load Factory Default Change Password ‰ Overview ‰ Installing NPort Administrator ‰ Configuration Configuring NPort Administrator Installing NPort Administrator Page Page Configuration Specify by IP Address Broadcast Search Unlock Password Protection Password Protection Configuring the NPort Page Page Upgrading the Firmware Web ConsolePage Import Configuration Export Configuration Broadcast Search Æ Monitor Æ Add Target Monitor Æ Add Target Æ Rescan Once the Monitor function is running Monitor Æ Load Configured COM PortPage Page Page Port Monitor On-line COM Mapping COM MappingPage Fast Flush only flush local buffer Page Page Off-line COM Mapping Page IP Address Report Automatic Message Log IP Serial LIB What is IP Serial Library? Why Use IP Serial Library?How to install IP Serial Library? Example Program IP Serial LIB Function GroupsServer Control Port Control Input/Output Data Port Status Miscellaneous Pinouts and Cable Wiring Ethernet Port Pinouts Serial Port Pinouts Port Pinout Diagrams Cable Wiring Diagrams Ethernet Cables Serial CablesDB9 Female to DB9 Male for NPort DB9 Female to DB25 Male for NPort Well Known Port Numbers TCP Socket Application Service NPort 5400 Series User’s Manual Well Known Port Numbers UDP Socket Application Service IP MIB Icmp MIB Snmp Agents with MIB II & RS-232 like group Address Translation MIB System MIB Interfaces MIB TCP MIB Snmp MIB Input Signal Table Output Signal Table Auto IP Report Protocol Info n Auto IP Report FormatID List AP ID & Hardware ID Mapping Table Service Information Following services are provided Moxa Internet Services Problem Report Form Moxa Product† NPortSerial Number Product Return Procedure