Default Settings | Moxa Technologies AWK-1100, MOXA AirWorks

A

Default Settings

TIP	Press the Reset (SF-Reset, or Soft-Reset) switch on the housing of a powered-onAP to reset the
	configuration settings to factory-default values.


	Setting Name	Default Value
	Global
	User Name	admin
	Password	root
	IEEE 802.11g
	Regulatory Domain	FCC (U.S.) or ETSI (Europe)
	Channel Number	11 for FCC or 13 for ETSI
	SSID	MOXA
	SSID Broadcasts	Enabled
	Transmission Rate	Auto
	Transmit Power	100%
	MAC Address	See the label on the accompanying PCMCIA card
		or the label on the housing of the AWK-1100.
	Security Mode	Open System
	Selected WEP Key	Key #1
	WEP Key #1	00-00-00-00-00
	WEP Key #2	00-00-00-00-00
	WEP Key #3	00-00-00-00-00
	WEP Key #4	00-00-00-00-00
	MAC-Address-Based Access Control	Disabled
	Access Control Table Type	Inclusive
	Wireless Client Isolation	Disabled
	AP Load balancing	Disabled
	Link Integrity	Disabled
	Association Control
	Max Number of Clients	64
	Block Clients if Traffic Load Exceeds	Disabled

Image 41

Moxa Technologies AWK-1100, MOXA AirWorks user manual Default Settings

Contents

First Edition, July Moxa AirWorks AWK-1100 User’s Manual Disclaimer Copyright NoticeTrademarks Table of Contents Page Introduction Product Features Package ChecklistProduct Specifications Overview Mechanical Page Getting Started ‰ Confirming the Settings of the AP and Client Computers First-Time Installation and Configuration AP Client Select the Operational Mode for AWK-1100AP/Bridge Review and Apply Settings Configure AWK-1100’s Ieee 802.11 settings Configuring Ieee 802.11g-related Settings Deploying the Access Point APSetting up Client Computers Checking if the Ieee 802.11g-related Settings Work Confirming the Settings of the AP and Client ComputersConfiguring TCP/IP-related Settings To check if a client computer can assess the Internet Checking if the TCP/IP-related Settings WorkPage ‰ Viewing Status Web Console Configuration Menu Structure Home and Refresh Buttons Save, Save & Restart, and Cancel Buttons Viewing Status Associated Wireless ClientsCurrent Dhcp Mappings System Log Specifying the Operational Mode Link Monitor AP Client mode onlyGeneral Operations STA-AP Managing the Firmware Administrative PasswordUpgrading Firmware by Http AP/Bridge AP Client Upgrading Firmware by Tftp Backing up and Restoring Configuration Settings by Http Choose Tftp as the Firmware management protocol Backing up and Restoring Configuration Settings by Tftp Addressing Configuring TCP/IP-related SettingsResetting the Configuration to Factory Defaults Static Dhcp Mappings Dhcp Server AP/Bridge modes onlyBasic Link Integrity Configuring Ieee 802.11g-related SettingsCommunication AP Load Balancing Wireless Distribution SystemAssociation Control Sample wireless bridge network topology Security STA Shared Key , and Auto Set the Access control type to inclusive MAC-Address-Based Access ControlSet the Access control type to exclusive Click Download Ieee 802.1X/RADIUS AP mode only Internet Packet Filters Configuring Advanced SettingsEthernet Type Filters IP Protocol Filters TCP/UDP Port Filters ManagementUPnP System Log Snmp Page Default Settings Management LAN InterfaceSnmp read community Snmp write community Wireless client computer cannot associate with an AWK-1100 TroubleshootingWireless Settings Problems AP does not respond to ping from the client computer TCP/IP Settings Problems Unknown Problems Moxa AirWorks AWK-1100 User’s Manual TTE Compliance Statement Regulatory StatementFederal Communication Commission Interference Statement Moxa AirWorks AWK-1100 User’s Manual Regulatory Statement Service Information Following services are provided Moxa Internet Services Moxa Product † AWK-1100-US † AWK-1100-EU Serial Number Problem Report Form Product Return Procedure