Configuring Relay Warning, Account Name | Moxa Technologies PT-7728

	PT-7728 User’s Manual		Featured Functions
		Account Name

		Setting	Description	Factory Default
		Max. 45 Charters	Your email account.	None
		Password Setting

		Setting	Description	Factory Default
		Disable/Enable to	To reset the password from the Web Browser interface,	Disable
		change password	click the Change password check-box, type the Old
			password, type the New password, retype the New
			password, and then click Activate; Max. 45 characters.
		Old password	Type the current password when changing the password	None
		New password	Type new password when enabled to change password;	None
			Max. 45 characters.
		Retype password	If you type a new password in the Password field, you	None
			will be required to retype the password in the Retype
			new password field before updating the new password.
		Email Address
		Setting	Description	Factory Default
		Max. 30	You can set up to 4 email addresses to receive alarm	None
		characters	emails from PT-7728.
		Send Test Email
		After finishing with the email settings, you should first click Activate to activate those settings,
		and then press the Send Test Email button to verify that the settings are correct.

	NOTE	Auto warning e-mail messages will be sent through an authentication protected SMTP server that
		supports the CRAM-MD5, LOGIN, and PAIN methods of SASL (Simple Authentication and

Security Layer) authentication mechanism.

We strongly recommend not entering your Account Name and Account Password if auto warning e-mail messages can be delivered without using an authentication mechanism.

Configuring Relay Warning

The Auto Relay Warning function uses relay output to alert the user when certain user-configured events take place. There are two basic steps required to set up the Relay Warning function:

1.Configuring Relay Event Types

Select the desired Event types from the Console or Web Browser Event type page (a description of each event type is given later in the Relay Alarm Events setting subsection).

2.Activate your settings

After completing the configuration procedure, you will need to activate your PT-7728’s Relay Event Types.

3-58

Image 72

Moxa Technologies PT-7728 Configuring Relay Warning, Account Name, Password Setting, Email Address, Send Test Email

Contents

Moxa PowerTrans Switch PT-7728 User’s Manual First Edition, February Moxa Inc Copyright Notice TrademarksDisclaimer Table of Contents Appendix a MIB Groups Appendix B Specifications ‰ Overview ‰ Package Checklist ‰ Software Features Introduction Package Checklist Software FeaturesOverview Getting Started Serial Console Configuration 115200, None, 8, 1, VT100 PT-7728 User’s Manual Getting Started Configuration by Telnet Console Key Function PT-7728 User’s Manual Getting Started PT-7728 User’s Manual Getting Started Configuration by Web Browser Disabling Telnet and Browser Access Featured Functions Configuring Basic Settings System Identification Password PasswordAccount Accessible IP Grant access to one host with a specific IP addressGrant access to any host on a specific subnetwork Hosts That Need Access Input Format Enable PortDescription Name Network SpeedFDX Flow Ctrl Auto IP Configuration Switch IP AddressSwitch Subnet Mask Default Gateway Time Daylight Saving TimeCurrent Time Current Date System File Update-By Remote Tftp Configuration Files Path and Name Tftp Server IP/NameFirmware Files Path and Name Log Files Path and Name System File Update-By Local Import/Export Factory Default Using Port Trunking Port Trunking Concept Configuring Port Trunking Trunk Group Maximum of 4 trunk groupsTrunk Type Available Ports/Member Ports Configuring Snmp Setting DescriptionTrunk Table Snmp Read/Write Settings Snmp VersionsV1, V2c Read Community V1, V2c Write/Read Community Setting Description Factory Default 1st Trap Server IP/Name Setting Description Factory Default Using Communication Redundancy Private MIB information Initial setup for Turbo Ring or Turbo Ring Turbo Ring Concept Turbo Ring with odd number switches Ring Coupling Configuration Determining the Redundant Path for Turbo Ring Switch B Configuring Turbo Ring and Turbo Ring Dual-Homing Configuration for Turbo RingConfiguring Turbo Ring Now Active Master/SlaveRedundancy Protocol Set as Master Enable Ring Coupling Coupling PortCoupling Control Port Enable Ring Ring 1/2-StatusRing 1/2-1st Ring Port Status Ring 1/2-2nd Ring Port Status Coupling-Mode Coupling Mode Primary/Backup Port What is STP? STP/RSTP Concept PT-7728 User’s Manual Featured Functions STP Configuration How STP WorksSTP Requirements Port Speed Path Cost 802.1D Edition 802.1w-2001 STP Reconfiguration Differences between Rstp and STPSTP Example Using STP on a Network with Multiple VLANs Configuring STP/RSTP Root/Not RootProtocol of Redundancy Bridge Priority Forwarding Delay Enable STP per PortHello Time sec Max. Age sec Using Traffic Prioritization Configuration Limits of RSTP/STPWhat is Traffic Prioritization? Traffic Prioritization Concept How Traffic Prioritization Works Ieee 802.1p Priority Level Ieee 802.1D Traffic Type Differentiated Services DiffServ Traffic Marking Traffic PrioritizationTraffic Queues Configuring Traffic Prioritization QoS ClassificationQueuing Mechanism Inspect TOS Setting Description Factory CoS MappingTOS/DiffServ Mapping Inspect COS Using Virtual LAN What is a VLAN?Virtual LAN Vlan Concept VLANs and the PowerTrans Benefits of VLANsManaging a Vlan Communication Between VLANs Sample Applications of VLANs using PT-7728 VLANs Tagged and Untagged Membership PT-7728 User’s Manual Featured Functions Configuring Virtual LAN Vlan SettingsManagement Vlan ID Port Type Using Multicast Filtering What is an IP Multicast?Concept of Multicast Filtering Vlan Table Benefits of Multicast Multicast FilteringNetwork without multicast filtering Multicast Filtering and Moxa PowerTrans Switch Igmp Internet Group Management Protocol Snooping ModeQuery Mode Network with multicast filtering Configuring Igmp Snooping Igmp Multicast FilteringGmrp Garp Multicast Registration Protocol Static Multicast MAC Igmp Snooping Settings Add Static Multicast MAC Using Bandwidth Management Configuring GmrpGmrp enable Gmrp Table Configuring Bandwidth Management Broadcast Storm Protection Traffic Rate Limiting SettingsIngress Using Port Access Control Configuring Static Port LockStatic Port Lock Ieee Configuring Ieee Database OptionRadius Server Server Port 802.1X Re-Authentication Local User Database Setup Using Auto Warning Port Access Control TableLocal User Database Setup Configuring Email Warning Event Type Email Setup MoxaPowerTransSwitch0001@SwitchLocationPort Events Mail Server IP/Name Configuring Relay Warning Password SettingAccount Name Email Address Event Setup Using Line-Swap-Fast-Recovery Using Set Device IPConfiguring Line-Swap Fast Recovery Override relay alarm settings Configuring Set Device IP Set up the connected devices Using Diagnosis Mirror Port Using Monitor Monitor by SwitchPing Using the MAC Address Table Monitor by Port Using Event Log MAC Using Syslog Syslog Server PT-7728 User’s Manual Featured Functions MIB II.1 System Group MIB II.2 Interfaces GroupMIB II.4 IP Group MIB II.5 Icmp Group MIB II.10 Transmission Group MIB II.11 Snmp GroupMIB II.17 dot1dBridge Group Public Traps Private Traps Switch Properties TechnologyInterface Power Optical Fiber 100BaseFX Warranty MechanicalEnvironmental