Manuals / Multi-Tech Systems / Computer Equipment / Switch

Multi-Tech Systems FR111 owner manual Recording MultiFRAD Information

Models: FR111

1 99

Download 99 pages 3.89 Kb

Page 88

7.3.1 Recording MultiFRAD Information

Please fill in the following information on your Multi-Tech MultiFRAD. This will help Tech Support in answering your questions. (The same information is requested on the Warranty Registration Card.)

Model Number: ______________________________________

Serial Number: ______________________________________

Firmware Version: ____________________________________

The model and serial numbers are on the bottom of your MultiFRAD. The Diagnostics menu displays the PROM firmware version number.

Before calling Tech Support, please note in the space below if your MultiFRAD is connected to a synchronous or asynchronous device on the data port. Also note status information about your MultiFRAD, including LED indicators, screen messages, diagnostic test results, or problems with a specific application, etc.

_________________________________________________________________________________

_________________________________________________________________________________

_______________________________________________________________________________

________________________________________________________________________________________________________

______________________________________________________________________________________________________________

_______________________________________________________________________________________________________

___________________________________________________________________________________________________________________

_________________________________________________________________________________________________________________________

___________________________________________________________________________________________________________________

_________________________________________________________________________________________________________________________

___________________________________________________________________________________________________________________

_________________________________________________________________________________________________________________________

88

Image 88

Multi-Tech Systems FR111 owner manual Recording MultiFRAD Information, Model Number Serial Number Firmware Version

Contents

Model FR111 Single Port Frame Relay Access Device with 56K DSUOwners Manual Reorient or relocate the receiving antenna Increase the separation between the equipment and receiverConsult the dealer or an experienced raido/TV technician for help both amended byPage Owners Manual 82067401 Revision B MultiFRADTM 100-Series Model No FR111Patents TRADEMARKSContents Chapter 3 - SetupChapter 4 - Software Loading and Configuration Chapter 1 - Introduction and DescriptionAppendices Chapter 7 - Service, Warranty and Tech SupportChapter 6 - ASCII Terminal Menu System Introduction and Description Page 1.1 Introduction Figure 1-1. MultiFRAD 100-SeriesChapter 3 - Setup Chapter 4 - Software Loading and Configuration1.2 About This Manual Chapter 1 - Introduction and DescriptionChapter 7 - Service, Warranty and Tech Support Chapter 6 - ASCII Terminal Menu System1.3.1 Ordering a Frame Relay Line 1.3 A Typical ApplicationFigure 1-2. Typical Frame Relay Network 1.3.2 How to Configure a MultiFRAD Page Page 1.4 FCC Regulations for Telephone Line Intercon- nection Service Center in U.S.A commission or corporation commission for information9. If so required, this equipment is hearing aid compatible Manufacturer1.5 Canadian Limitations Notice 1.6 Specifications Data Port TrunkElectrical/Physical/Environmental CompatibilityPage Front and Back Panel Descriptions Page 2.1 Introduction 2.2 Front PanelFigure 2-1. Front Panel DataTrunk Power Connector Trunk ConnectorData Connector 2.3 Back Panel2.4 Switch Settings Figure 2-3. Switch SettingsTable 2-1. Switch Settings Switch2.5 Shunts Figure 2-4. ShuntsPage Setup Page 3.1 Introduction 3.3 Safety Warnings3.2 Unpacking 3.4 Setup Figure 3-1. DIP-Switch SettingsFigure 3-2. Power Connection Figure 3-3. Data ConnectionPower DataFigure 3-4. Trunk Connection Trunk3.5 V.35 Shunt Figure 3-5. ShuntsSoftware Loading and Configuration Page 4.1 Introduction 4.2 Loading SoftwarePage Page 4.3 Configuring Your MultiFRAD using Windows Page 10 The Back to Back check box should normally remain unchecked 12 Click on the OK button to return to the Main menu 14 The Configuration dialog box is displayedYour MultiFRAD 100 is fully operational at this time Configurations 1 - Data Port Configuration 2 - Trunk Configuration 4.4 Configuring your MultiFRAD using a Dumb TerminalM - Main Menu P - Previous Menu Selection Data Port Configuration Valid values are between 0016 to Enter the DLCIData Link Connection Identifierx - Enter Number, or P - Previous Menu Selection x - Enter Number, or P - Previous Menu Selectionx - Enter Number, or P - Previous Menu Selection Management Type 1 - Annex D ANSI T1.617 2 - LMI 3 - Annex A ITU-T Q.933 P - Previous Menu SelectionEnter a number that is less than or equal to the Monitored Event Count Page Software Utility Descriptions Page 5.1 Introduction 5.2 MultiFRAD Main Menu5.2.1 Configuration Data Port Diagnostics5.2.2 Others Statistics 5.2.3 Download5.2.5 Help 5.2.6 MultiFRAD Version5.3 Data Port Configuration Mode Asynchronous/SynchronousSync Mode Parameters SpeedBetween Frames InterFrame Timer in mSEncoding Scheme CRC Preset Async Mode ParametersBaud Rate Word LengthParity Stop BitsFlow Control PacingPass Xon EchoEIA Pass Through Trunk FacilityENQ/ACK Data Link Connection Identifier DLCI 5.4 Trunk ConfigurationManagement Type Encapsulation Type Management Parameters Polling IntervalError Threshold Full Status CounterMonitored Event Committed Info Rate CIRBack to Back Excess Burst Rate Be5.6 Diagnostics 5.5 StatisticsLoop Tests Other TestsPage ASCII Terminal Menu System Page 6.2 Configurations Menu 6.1 Introduction6.2.1 Async Data Port Configuration The Word Length option sets the number of bits in a word. The word length range is 5 to 8 bits. The default is 8 bits 4 IN Trunk Facility20 IN 6.2.2 Sync Data Port Configuration Page 6.2.3 Trunk Configuration Page should be less than or equal to the Monitored Event Counter Statistics 1 - View Statistics 6.3 StatisticsP - Previous Menu Selection Page 6.4 Reset Options 6.5 Diagnostic Tests6.5.1 Loop Tests Flash Firmware UpgradeThe methodology for all of the tests is the same 6.5.5 Flash Firmware Upgrade 6.5.2 Memory Test6.5.3 Watch Dog Test 6.5.4 Product and Firmware IDService, Warranty and Tech Support Page 7.1 Introduction 7.2 Limited Warranty7.3 Tech Support 7.3.1 Recording MultiFRAD Information Model Number Serial Number Firmware Version7.3.2 Service ATTN SERVICE OR REPAIRS7.4 About the Multi-Tech BBS MULTI-TECH SYSTEMS, INC 2205 WOODALE DRIVE MOUNDS VIEW, MINNESOTA7.4.2 Downloading a File 7.4.1 Logging on to the Multi-Tech BBSIf you know the file name 7.5 About CompuServe If you don’t know the file name7.6 About the Internet 7.7 About the Multi-Tech Fax-Back Serviceftp//ftp.multitech.com 7.8.1 Using FlashPro to Upgrade MultiFRAD Firmware 7.8 Upgrading the Flash PROMPage Appendices Page Appendix A Cabling Diagrams Data connector RS232C/V.24 * CableTo FR111 Data Connector Data CablesTrunk Cable Pin IdentificationRJ-48 Cable 1 2 3 4 5 6 7RJ48S Back-To-Back CableRJ48S