Manuals / Multi-Tech Systems / Computer Equipment / Switch

Multi-Tech Systems FR111 ASCII Terminal Menu System, Service, Warranty and Tech Support

Models: FR111

1 99

Download 99 pages 3.89 Kb

Page 11

Chapter 6 - ASCII Terminal Menu System

Chapter 6 provides a description of the ASCII terminal menu system. The ASCII terminal menu system is used when a dumb terminal is connected to the data port. These menus allow you to configure the data port and trunk, view statistics, reset the unit, and enable diagnos- tics.

Chapter 7 - Service, Warranty and Tech Support

Chapter 5 provides instructions on getting service for your MultiFRAD at the factory, a statement of the limited warranty, information about our user bulletin board service, and space for recording information about your MultiFRAD prior to calling Multi-Tech's Technical Support. The final three sections explain how to use our bulletin board service (BBS), and get support through CompuServe and the Internet.

11

Image 11

Multi-Tech Systems FR111 owner manual ASCII Terminal Menu System, Service, Warranty and Tech Support

Contents

Owners Manual Single Port Frame Relay Access Device with 56K DSUModel FR111 both amended by Reorient or relocate the receiving antennaIncrease the separation between the equipment and receiver Consult the dealer or an experienced raido/TV technician for helpPage TRADEMARKS Owners Manual 82067401 Revision BMultiFRADTM 100-Series Model No FR111 PatentsChapter 1 - Introduction and Description ContentsChapter 3 - Setup Chapter 4 - Software Loading and ConfigurationChapter 6 - ASCII Terminal Menu System Chapter 7 - Service, Warranty and Tech SupportAppendices Introduction and Description Page Figure 1-1. MultiFRAD 100-Series 1.1 IntroductionChapter 1 - Introduction and Description Chapter 3 - SetupChapter 4 - Software Loading and Configuration 1.2 About This ManualChapter 6 - ASCII Terminal Menu System Chapter 7 - Service, Warranty and Tech SupportFigure 1-2. Typical Frame Relay Network 1.3 A Typical Application1.3.1 Ordering a Frame Relay Line 1.3.2 How to Configure a MultiFRAD Page Page 1.4 FCC Regulations for Telephone Line Intercon- nection Manufacturer Service Center in U.S.Acommission or corporation commission for information 9. If so required, this equipment is hearing aid compatible1.5 Canadian Limitations Notice Compatibility 1.6 Specifications Data PortTrunk Electrical/Physical/EnvironmentalPage Front and Back Panel Descriptions Page Data 2.1 Introduction2.2 Front Panel Figure 2-1. Front PanelTrunk 2.3 Back Panel Power ConnectorTrunk Connector Data ConnectorSwitch 2.4 Switch SettingsFigure 2-3. Switch Settings Table 2-1. Switch SettingsFigure 2-4. Shunts 2.5 ShuntsPage Setup Page 3.2 Unpacking 3.3 Safety Warnings3.1 Introduction Figure 3-3. Data Connection 3.4 SetupFigure 3-1. DIP-Switch Settings Figure 3-2. Power ConnectionTrunk PowerData Figure 3-4. Trunk ConnectionFigure 3-5. Shunts 3.5 V.35 ShuntSoftware Loading and Configuration Page 4.2 Loading Software 4.1 IntroductionPage Page 4.3 Configuring Your MultiFRAD using Windows Page 10 The Back to Back check box should normally remain unchecked Your MultiFRAD 100 is fully operational at this time 14 The Configuration dialog box is displayed12 Click on the OK button to return to the Main menu M - Main Menu P - Previous Menu Selection 4.4 Configuring your MultiFRAD using a Dumb TerminalConfigurations 1 - Data Port Configuration 2 - Trunk Configuration Data Port Configuration x - Enter Number, or P - Previous Menu Selection Enter the DLCIData Link Connection IdentifierValid values are between 0016 to x - Enter Number, or P - Previous Menu Selection Selectionx - Enter Number, or P - Previous Menu 3 - Annex A ITU-T Q.933 P - Previous Menu Selection Management Type 1 - Annex D ANSI T1.617 2 - LMIEnter a number that is less than or equal to the Monitored Event Count Page Software Utility Descriptions Page 5.2 MultiFRAD Main Menu 5.1 Introduction5.2.3 Download 5.2.1 Configuration Data PortDiagnostics 5.2.2 Others Statistics5.2.6 MultiFRAD Version 5.2.5 HelpSpeed 5.3 Data Port ConfigurationMode Asynchronous/Synchronous Sync Mode ParametersEncoding Scheme InterFrame Timer in mSBetween Frames Word Length CRC PresetAsync Mode Parameters Baud RatePacing ParityStop Bits Flow ControlTrunk Facility Pass XonEcho EIA Pass ThroughENQ/ACK Management Type 5.4 Trunk ConfigurationData Link Connection Identifier DLCI Management Parameters Polling Interval Encapsulation TypeCommitted Info Rate CIR Error ThresholdFull Status Counter Monitored EventExcess Burst Rate Be Back to Back5.5 Statistics 5.6 DiagnosticsOther Tests Loop TestsPage ASCII Terminal Menu System Page 6.1 Introduction 6.2 Configurations Menu6.2.1 Async Data Port Configuration The Word Length option sets the number of bits in a word. The word length range is 5 to 8 bits. The default is 8 bits 20 IN Trunk Facility4 IN 6.2.2 Sync Data Port Configuration Page 6.2.3 Trunk Configuration Page should be less than or equal to the Monitored Event Counter P - Previous Menu Selection 6.3 StatisticsStatistics 1 - View Statistics Page Flash Firmware Upgrade 6.4 Reset Options6.5 Diagnostic Tests 6.5.1 Loop TestsThe methodology for all of the tests is the same 6.5.4 Product and Firmware ID 6.5.5 Flash Firmware Upgrade6.5.2 Memory Test 6.5.3 Watch Dog TestService, Warranty and Tech Support Page 7.3 Tech Support 7.2 Limited Warranty7.1 Introduction Model Number Serial Number Firmware Version 7.3.1 Recording MultiFRAD InformationMULTI-TECH SYSTEMS, INC 2205 WOODALE DRIVE MOUNDS VIEW, MINNESOTA 7.3.2 ServiceATTN SERVICE OR REPAIRS 7.4 About the Multi-Tech BBSIf you know the file name 7.4.1 Logging on to the Multi-Tech BBS7.4.2 Downloading a File If you don’t know the file name 7.5 About CompuServeftp//ftp.multitech.com 7.7 About the Multi-Tech Fax-Back Service7.6 About the Internet 7.8 Upgrading the Flash PROM 7.8.1 Using FlashPro to Upgrade MultiFRAD FirmwarePage Appendices Page Data Cables Appendix A Cabling DiagramsData connector RS232C/V.24 * Cable To FR111 Data Connector1 2 3 4 5 6 7 Trunk CablePin Identification RJ-48 CableRJ48S Back-To-Back CableRJ48S