Power or Recharge a USB Device | NETGEAR PR2000 instruction

Trek N300 Travel Router and Range Extender PR2000

Power or Recharge a USB Device

When your Trek is powered by an AC wall outlet, you can power or recharge a USB device from the Trek’s USB port. For example, you can use the USB port to recharge your cell phone. For information about how to locate the USB port, see Enhance Your Local Network on page 67.

When the Trek is powered from a micro USB cable, you cannot use the Trek’s USB port as an auxiliary power source. For more information about your choices of providing power to the Trek, see Power Inputs on page 12.

The maximum power that is supplied by the Trek’s USB port is a current of 900 mA at 5 volts. To find out how much current your USB device draws, see the manual that came with your device.

USB Port

86

Image 86

NETGEAR PR2000 user manual Power or Recharge a USB Device

Contents

Netgear Trek N300 Travel Router and Range Extender Trademarks SupportCompliance Contents Security Appendix a Supplemental Information Hardware Setup Get to know your Trek Unpack Your Trek Position Your Trek  To prepare your Trek for installation Prepare Your Trek Internet Mode Switch Get to Know Your Netgear Trek Indicator LEDs Netgear Connection Ports and Reset Button USB Power Inputs Netgear Antenna Orientation Product Label WiFi Connection at a Public Hotspot Setup Different Ways You Can Connect to the Internet  To connect to a public WiFi hotspot WiFi hotspot connection WiFi Range Extender Setup  To use the Trek as a WiFi range extender DON’T Internet Connection at Home Setup  To connect to the Internet with an Ethernet cable Hardware Setup WiFi Bridge Setup  To use the Trek as a WiFi bridge Hardware Setup Get Started with Netgear genie Connect to the Trek Wireless Devices and Security Settings Trek Setup PreparationTypes of Logins and Access Use Standard TCP/IP Properties for Dhcp Netgear genie Setup  To use Netgear genie to set up your Trek Use Netgear genie After Installation  To view or change the settings for the Trek Upgrade the Trek Firmware Change the Password Password Recovery Select Advanced Administration Set Password  To set up password recovery  To recover your password Manual Method Add Wireless Devices or Computers to Your Trek To connect WiFi devices manually to your Trek Click Advanced WPS Wizard Wi-Fi Protected Setup Method To connect WiFi devices to your Trek with WPS Push Button recommended. Click the button Netgear genie App and Mobile genie App Genie mobile app home screen Genie Basic Settings Your Internet connection and network  To view or change the Internet setup Internet SetupWired WAN Connection Router Mode Internet Service Provider. Select PPPoE, L2TP, or Pptp Select Basic Internet Wired WAN Connection Wireless AP Mode  To view or change the Internet setup Genie Basic Settings Wireless WAN Connection WiFi Mode Select the To save a name for profile check box Basic Wireless Settings To view or change basic wireless settings Select Basic Wireless Change the Wireless Security Option  To change the WPA settings Netgear recommends that you do not disable security Select Basic Attached Devices Attached Devices To view the attached devices Profile Settings  To view or delete the saved profile settings Select Basic Profile Settings Specify custom settings Genie Advanced Home Setup Wizard  To launch the Setup Wizard Click the Take me to the Internet button Select Advanced Setup WAN Setup WAN Setup To change the WAN settings Default DMZ Server  To set up a default DMZ server Change the MTU Size Common MTU sizes LAN Setup  To change the MTU size  To change the LAN settings Select Advanced Setup LAN Setup Use the Trek as a Dhcp Server  To disable the Dhcp server feature Set Up Address Reservation  To reserve an IP address  To edit or delete a reserved address entry Quality of Service Setup Wi-Fi Multimedia Quality of Service for Wireless Traffic Quality of Service Priority Rules and Internet Access  To set up QoS Scroll down Genie Advanced Home Genie Advanced Home Genie Advanced Home USB Port Enhance your local network Enhance Your Local Network  To connect a USB storage device Set Up Network StorageConnect or Safely Remove a USB Drive  To remove a USB disk drive safely View or Configure a USB Drive  To view basic information about the USB storage device Select Basic ReadySHARE Configure the USB Storage Device and Access Settings To view or change the USB storage advanced settings Select Basic ReadySHARE Configure the Available Network Folders  To view network folders  To add a network folder Click the Create Network Folder button  To edit a network folder  To set up approved USB devices Specify Approved USB Devices Select the Allow only approved devices check box Access and Share Your Network StorageCommon Uses of Network Sharing Share Photos and Multimedia Access Your USB Storage Device Locally  To map the USB device to a local Windows network drive  To access the USB drive with FTP from a remote computer Access Your USB Storage Device Remotely To access the USB drive from a remote computer Set Up a Network Printer  To set up ReadySHARE Printer USB Port USB Port USB Port USB Port Power or Recharge a USB Device Keep unwanted content out of your Security Port Filtering to Block Services  To block services Select Advanced Security Block Services Defined Select Advanced Security Schedule Schedule Blocking To schedule blocking  To set up email notifications Security Event Email Notifications Security Administration Manage your network  To view Trek status and usage information View Trek StatusRouter Information Pane  To display the Router Information pane  To display the Internet Port pane Internet Port PaneLAN Port Statistics  To view the traffic statistics Connection Status  To view and manage the connection status Administration Wireless Settings Pane  To display the Wireless Settings pane Administration 101  To view and manage the logs Specify Log SettingsSelect Advanced Administration Logs  To specify log settings Restore Configuration Settings Manage the Configuration FileBack Up Settings  To erase the configuration settings Erase the Current Configuration SettingsDo not interrupt the reboot process Update the Trek Firmware  To check for new firmware and update your Trek Select Advanced Administration Firmware Update Advanced Settings Fine-tune your network  To turn the wireless radio on or off Advanced Wireless SettingsControl the Wireless Radio Select Advanced Advanced Setup Wireless Settings Set Up a Wireless Schedule  To configure and enable the wireless schedule View or Change WPS Settings  To specify WPS settings Advanced Settings 112 Set Up a Wireless Access List by MAC Address  To restrict access based on MAC addresses Select the Turn Access Control On check box  To set up Dynamic DNS Dynamic DNS Static Routes Select Advanced Advanced Setup Dynamic DNSSelect the Use a Dynamic DNS Service check box  To set up a static route Select Advanced Advanced Setup Static Routes  To edit or delete a static route  To set up remote management Remote Management Advanced Settings 120  To turn on Universal Plug and Play Select Advanced Advanced Setup UPnPUniversal Plug and Play Traffic Meter  To monitor Internet traffic Click Advanced Advanced Setup Traffic Meter Select Advanced Advanced Setup Traffic Meter Advanced Settings 125 Troubleshooting Diagnose and solve problems Quick Tips Troubleshoot with the LEDs Internet Port LED is Off Power LED Is OffLEDs Never Turn Off WiFi LED is Off Cannot Log In to the Trek  To check the WAN IP address Cannot Access the InternetSelect Administration Router Status Troubleshoot PPPoE  To troubleshoot a PPPoE connection Troubleshoot Internet Browsing  To display the current date and time Changes Not SavedIncorrect Date or Time Wireless Connectivity Restore the Factory Settings and Password Troubleshoot Your Network Using the Ping Utility  To ping the Trek from a running Windows computer Test the LAN Path to Your TrekTest the Path from Your Computer to a Remote Device Troubleshooting 137 Supplemental Information View the Trek specs Factory Settings Factory default settings Technical Specifications PR2000 Trek specifications Supplemental Information 141 Index 142 143 144 145