ENGLISH

USER MANUAL

SNOW CUTTER ASSEMBLY AND USE (optional)

CAUTION!

To install this equipment, the sweeper should be equipped with the appropriate fitting.

Snow cutter assembly

1.Disassemble the suction inlet (17, Fig. G) (see the procedure in the relevant paragraph).

2.Disassemble the 3rd broom arm (23, Fig. G) (see the procedure in the relevant paragraph).

3.Operating on a level ground, bring the sweeper into a suitable position to install the snow cutter (Fig. AW).

4.Turn off the engine and engage the parking brake (13, Fig. E).

5.Place the snow cutter on the arms (15, Fig. AW) and secure it with the screws (13).

6.On both sides of the machine, tighten the screws (14, Fig. AW) on the arms (15).

7.Remove the protection cover, then connect the hydraulic system quick couplings (1, Fig. AV) to the corresponding pipe couplings (3).

8.Connect the hydraulic system quick coupling (2, Fig. AW) to the pipe coupling (4), which corresponds to the pipe (2, Fig. AY) used for the suction inlet.

9.Open the left side upper and lower lids (9 and 11, Fig. G) by disengaging the fasteners (10 and 12) with the supplied key.

10.If present, turn the lever (17, Fig. AW) from the position (17a) (high-pressure water gun activation) to the position (17b) (snow cutter activation).

NOTE

The lever (17, Fig. AW) is present only if the machine is equipped with the high-pressure washing system (see 21 and 22, Fig. F).

11.Close the left side upper and lower lids (11 and 9, Fig. G) by engaging the fasteners (10 and 12) with the supplied key.

12.Now the machine is ready to operate with the snow cutter.

Snow cutter disassembly

13.Disassemble the snow cutter in the reverse order of assembly.

14.Secure and protect the snow cutter properly.

Snow cutter use

15.Assemble the snow cutter (Fig. AW) according to the procedure shown in the relevant paragraphs.

16.To lift/lower the snow cutter use the suction inlet lifting/lowering controls.

17.Turn on the snow cutter (10, Fig. AW) with the switch (30, Fig. D).

18.To change the snow cutter speed according to engine speed, use the knob (18, Fig. AW).

19.Before using the snow cutter (10, Fig. AW), check its height from the ground according to the following procedure.

•Drive the machine with the snow cutter on a level ground.

•Lower the snow cutter on the ground.

•Engage the parking brake with the lever (13, Fig. E).

•Turn off the engine, by turning the ignition key (24, Fig. D) counterclockwise, to the end of stroke, then remove it.

•Check the distance from the ground of the cutter (10, Fig. AW) along its length; if necessary adjust it, but keep a safety distance according to the type of ground/floor/road. Stones and gravel are dangerous because they can be thrown against people or objects, and cause damages to the machine.

To adjust the height of the cutter (10, Fig. AW), lift/lower the side sliding blocks (11) with the winches (12).

20.To direct the snow discharge pipe (7, Fig. AW), use the winch (16).

21.To direct the discharge baffle plate(5, Fig. AW), use the knobs (6).

22.To clean the snow cutter use the tool (8).

WARNING!

The snow cutter can be safely cleaned only when the machine and cutter are stopped!

23.Now the machine is ready to operate with the snow cutter.

If necessary, fit snow chains on the front wheels of the sweeper.

32

33014091(3)2008-02 A

RS 1300

Page 153 Page 155
Page 154
Image 154
Nilfisk-ALTO RS 1300 manuel dutilisation Snow cutter assembly, Snow cutter disassembly, Snow cutter use
Page 153 Page 155

RS 1300 specifications

Nilfisk-ALTO RS 1300 is a leading pressure washer renowned for its powerful performance and versatile applications. Designed for both commercial and residential use, this model caters to a wide range of cleaning needs, including patios, driveways, vehicles, and garden furniture.

One of the standout features of the RS 1300 is its robust motor, which delivers an impressive pressure of up to 130 bar. This high pressure allows users to tackle stubborn dirt and grime with ease. Coupled with a flow rate of up to 500 liters per hour, the machine ensures efficient cleaning in a shorter time frame.

The RS 1300 is equipped with a highly durable aluminum pump system that not only enhances the lifespan of the unit but also ensures consistent performance during heavy-duty cleaning tasks. The innovative design includes an adjustable pressure nozzle, which offers flexibility for various cleaning applications. Users can easily switch between different spray settings, allowing for tailored cleaning experiences.

In addition to its powerful performance, the Nilfisk-ALTO RS 1300 features a built-in detergent tank, making it convenient to use cleaning agents for enhanced results. This integration simplifies the cleaning process, as users can apply soap directly through the spray gun, boosting efficiency when dealing with tough stains.

Safety and ease of use are paramount in the design of the RS 1300. The machine comes with a safety lock feature to prevent accidental starts, providing peace of mind during storage and transport. Its ergonomic design ensures a comfortable grip, reducing user fatigue during prolonged use.

The RS 1300 is easy to transport, thanks to its lightweight design and integrated wheels. Users can effortlessly maneuver the unit around their property or job site. Additionally, storage is made simple with practical onboard storage solutions for the hose and accessories.

Overall, the Nilfisk-ALTO RS 1300 stands out for its combination of power, convenience, and user-friendly features. With its advanced technology and robust construction, it is a reliable choice for anyone seeking a high-performance pressure washer to tackle their cleaning challenges effectively. Whether for professional or home use, the RS 1300 is designed to meet the rigorous demands of various cleaning applications.
Top Page Image Contents