Manuals / Nilfisk-ALTO / Household Appliance / Vacuum Cleaner

Nilfisk-ALTO RS 1300 manuel dutilisation 3RD Broom ARM DISASSEMBLY/ASSEMBLY, Winter Maintenance

Models: RS 1300

1 224
Download 224 pages 52.13 Kb
Page 167
Image 167

USER MANUAL

ENGLISH

3RD BROOM ARM DISASSEMBLY/ASSEMBLY

NOTE

This is a basic procedure, it is often recalled during other procedures, when necessary.

CAUTION!

This procedure is applicable only for sweepers with appropriate fittings for the following equipments:

−Snow brush

−Snow cutter

Disassembly

1.Move the 3rd broom (21, Fig. G) aside, and lower the suction inlet (23) according to the procedure shown in the relevant paragraph.

2.Turn off the engine and engage the parking brake (13, Fig. E).

3.Operating according to the safety rules, with a proper hoisting system (1, Fig. AZ), sling the 3rd broom arm and arm extension

(2) in the points shown in the figure. Move the pipes and cable aside, to avoid squashing them during the lifting operation. 3rd broom arm weight: approximately 198.4 lb (90 kg).

4.Cut the clamps (3, Fig. AZ) securing cables and pipes.

5.Disconnect the three electrical connectors (4, Fig. AZ).

6.Disconnect the dust control system quick coupling (5, Fig. AZ) from the corresponding pipe coupling (6), then install the protection covers.

7.Disconnect the seven hydraulic system quick couplings (7, Fig. AZ) from the corresponding pipe couplings (5), then install the protection covers.

8.Unscrew the nut (8, Fig. AZ) securing the cylinder (9) to the 3rd broom arm extension and secure the cylinder to the machine with proper clamps.

9.Slightly tighten the hoisting system (1, Fig. AZ), then remove the four nuts (10) securing the 3rd broom arm extension to the machine.

10.Remove the arm and arm extension of the 3rd broom (2, Fig. AZ).

Assembly

11.Assemble the components in the reverse order of disassembly.

12.If necessary, check and adjust the 3rd broom position (see the procedure in the relevant paragraph).

WINTER MAINTENANCE

In winter, perform the following maintenance procedures carefully.

Procedures for machine storage or for machines working at less than +32°F (0°C)

1.Drain the nozzles and water tanks.

2.Drain and clean/replace the water filter.

3.Pour antifreeze in the water tanks (check the quantity).

4.Turn on the water pump (see the procedure in the relevant paragraphs) to let the antifreeze flow through the system until it comes out from the broom nozzles, from the suction hose nozzle and from the rear pipe nozzle (if equipped). When the antifreeze comes out from the nozzles, stop the pump.

5.Start the diesel engine as shown in the relevant paragraph.

6.Turn on the high-pressure washing system pump (see the procedure in the relevant paragraphs) and let the antifreeze flow through the high-pressure washing system until it comes out of the water gun. When the antifreeze comes out, stop the pump.

WARNING!

Do not use the dust control system when the outside temperature is lower than +32°F (0°C) because it can create ice sheets on the pavement.

Procedures to perform when the machine has been stored for two months

7.Replace the engine oil and oil filter (see the relevant paragraphs).

8.Fill the fuel tank (see the relevant paragraph).

9.Apply grease.

10.Charge the battery.

11.Check the wheel pressure (see the relevant paragraph).

Procedures to perform when the machine has been stored for three months

8.Perform the same procedures of the second month.

9.Each month connect a battery charger and keep the battery charged for 12/24 hours.

RS 1300

33014091(3)2008-02 A

45

Page 166 Page 168
Page 167
Image 167
Nilfisk-ALTO RS 1300 manuel dutilisation 3RD Broom ARM DISASSEMBLY/ASSEMBLY, Winter Maintenance
Page 166 Page 168

RS 1300 specifications

Nilfisk-ALTO RS 1300 is a leading pressure washer renowned for its powerful performance and versatile applications. Designed for both commercial and residential use, this model caters to a wide range of cleaning needs, including patios, driveways, vehicles, and garden furniture.

One of the standout features of the RS 1300 is its robust motor, which delivers an impressive pressure of up to 130 bar. This high pressure allows users to tackle stubborn dirt and grime with ease. Coupled with a flow rate of up to 500 liters per hour, the machine ensures efficient cleaning in a shorter time frame.

The RS 1300 is equipped with a highly durable aluminum pump system that not only enhances the lifespan of the unit but also ensures consistent performance during heavy-duty cleaning tasks. The innovative design includes an adjustable pressure nozzle, which offers flexibility for various cleaning applications. Users can easily switch between different spray settings, allowing for tailored cleaning experiences.

In addition to its powerful performance, the Nilfisk-ALTO RS 1300 features a built-in detergent tank, making it convenient to use cleaning agents for enhanced results. This integration simplifies the cleaning process, as users can apply soap directly through the spray gun, boosting efficiency when dealing with tough stains.

Safety and ease of use are paramount in the design of the RS 1300. The machine comes with a safety lock feature to prevent accidental starts, providing peace of mind during storage and transport. Its ergonomic design ensures a comfortable grip, reducing user fatigue during prolonged use.

The RS 1300 is easy to transport, thanks to its lightweight design and integrated wheels. Users can effortlessly maneuver the unit around their property or job site. Additionally, storage is made simple with practical onboard storage solutions for the hose and accessories.

Overall, the Nilfisk-ALTO RS 1300 stands out for its combination of power, convenience, and user-friendly features. With its advanced technology and robust construction, it is a reliable choice for anyone seeking a high-performance pressure washer to tackle their cleaning challenges effectively. Whether for professional or home use, the RS 1300 is designed to meet the rigorous demands of various cleaning applications.