Manuals / Nortel Networks / Computer Equipment / Network Card

Nortel Networks 1002rp manual Sample network setup Succession, Embedded LAN 10BaseT, G250017

Models: 1002rp

1 86

Download 86 pages 33.02 Kb

Page 27

Image 27

October 2006

1002rp server description

Sample network setup: Succession 1000

The following diagram shows a CallPilot server network setup with a Succession 1000 system.

i2004	Web-enabled	Desktop
i2004	CallPilot	client
Internet	administrative	PC
phonesets	PC

Telephony LAN/Customer LAN (10/100BaseT or 100BaseT)

	Internet	Succession
		1000 Media
	Telephony
		Gateway Expansion
	Gateway
		Modem
	Line Card

CallPilot

server

CE-MUX

DS-30x

Internet

Telephony

Gateway

Line Card

Router or Ethernet switch (optional)

Succession 1000

Call Server

Succession 1000

Media	MGate	MPB16-4
	card
Gateway		board

(NTRB18CA)

Embedded LAN (10BaseT)

Optivity

Telephony

Manager

Laptop	Web-enabled
	CallPilot
	administrative
	PC

G250017

1002rp Server Hardware Installation

Page 27

Image 27

Nortel Networks 1002rp manual Sample network setup Succession, Telephony LAN/Customer LAN 10/100BaseT or 100BaseT, G250017

Contents

Document Number Document Version Standard 1002rp Server Hardware InstallationCallPilot ReleaseTrademarks Copyright 2006 Nortel NetworksCRYSTAL REPORTS is a trademark of Seagate Software Inc Information for Japan Japan Denan statementJapan VCCI statement があります。この場合には使用者が適切な対策を取るように要求されることがあります。 CallPilot StandardPublication history Installation is issued for general release OctoberPublication history To connect the mouse, keyboard, and monitor to the server Task ListTo replace the front bezel after installation is complete To bring DC power and ground into the PDUTask List StandardCallPilot 4 Power supply installation ContentsHow to get Help 3 Preparing for installationStandard EMC emission level protection for the 1002rp ServerIndex ContentsGetting Help from the Nortel Web site How to get HelpGetting Help over the phone from a Nortel Solutions Center C h a p t e rGetting Help from a specialist by using an Express Routing Code Getting Help through a Nortel distributor or resellerHow to get Help 1002rp server description In this chapterC h a p t e r Server features Server dimensions and weightIntroduction Environmental specifications Front panel features front view without the front bezel Alarm boardG101750 1002rp server description Rear panel diagramPCISBC ISA connectors connector connectors Overhead view of empty server showing PCI and ISA connectorsSlot assignments Slot definition and slot numberingIntroduction Slot 1002rp slot assignmentsCallPilot-assigned MeridianSlot a. On some CallPilot Manager screens, the CallPilot-assigned board label is displayed. This label corresponds to the slot number. For example, BRD12 refers to the board in slot ensure that the CallPilot network is inside your Network connectivityTo secure the CallPilot server from unauthorized access IntroductionSample network setup Meridian G250017 Sample network setup SuccessionTelephony LAN/Customer LAN 10/100BaseT or 100BaseT Embedded LAN 10BaseTSwitch connectivity CallPilot ELAN and CLAN network setupMeridian 1 or Succession 1000 systems Network requirements Remote access connectivityIntroduction Supported peripheral devicesMaintenance Reference documentsInstallation and Configuration Administration1002rp server description StandardCallPilot In this chapter Preparing for installationInstallation overview C h a p t e rInstallation overview Installation checklistIntroduction For a DC-powered server, set up the DC power source see Conventions for warnings Unpacking the 1002rp server To unpack the equipmentIntroduction What’s next? Introduction Removing the front bezel and server coverRisk of equipment damage To remove the front bezelWhat’s next? To remove the server coverInspecting the server interior To inspect the server interiorIntroduction THEN replace the server cover and proceed with the hardware installationSee “Installation checklist” on page Preparing for installationTo replace the front bezel after installation is complete DC wire gauge tables Power supply installationSafety precautions Installing the second power supply module AC or DCSafety precautions Safety informationEquipment handling guidelines Power supply installation Installing the second power supply module AC or DCAbout the power supply module AC versus DC systemsG101751 Power supply modulesWhat’s next? To install the power supply moduleDC wire gauge tables Cabinet and module DC feed recommended wire gauge specificationsIntroduction AWG No Metric wire conversionIndustry standard Resistance at 20 CDC rack cabling Rack power and grounding 48 V DC power distribution rationale Introduction About the power distribution unitPDU power and grounding Multiple PDUsPDU terminal blocks and wiring diagram DC power inputSingle PDU wiring diagram Bringing power and ground into the PDU To bring DC power and ground into the PDUIntroduction Power supply installation StandardCallPilot Connecting the server to the ELAN Installing the server and connecting the peripheral devicesInstalling the server Connecting peripherals to the serverInstalling the server To install the serverIntroduction Preparing the modem Required equipmentIntroduction G101445 Modem DIP switchessetting To set the modem DIP switchesDefault switchWhat’s next? Installing the server and connecting the peripheral devicesStandardRear panel connectors Connecting peripherals to the serverTo connect the modem to the server To connect the mouse, keyboard, and monitor to the serverWhat’s next? Continue with “Connecting the server to the ELAN” on pageIntroduction Connecting the server to the ELANMedia Access Control address To connect the server to the ELANDANGER Risk of fire hazard 555-7101-210be connected to a CLAN continue with installing the softwarefeature dongle. See page What’s next?Introduction Connecting the server to the CLAN optionalTo connect the server to the CLAN Media Access Control addressWhat’s next? Continue with “Installing the Nortel software feature dongle” on pageSoftware Installing the Nortel software feature donglefeature key IntroductionContinue with “Connecting the server to power” on page To install the software feature dongleRequirements For installation, you require a Phillips No. 1 screwdriverBefore you begin Connecting the server to powerCallPilot serverG250018 To connect the 1002rp DC server to power To connect the 1002rp AC server to powerTo start the server A p p e n d i x A EMC emission level protection for the 1002rp ServerEMC emission level protection for the 1002rp Server Ferrites secured to an external cableNumerics IndexPage Page Index StandardCallPilot Page CallPilot 1002rp Server Hardware Installation