Manuals / Nortel Networks / Computer Equipment / Network Card

Nortel Networks 1002rp Installing the server and connecting the peripheral devices, C h a p t e r

Models: 1002rp

1 86

Download 86 pages 33.02 Kb

Page 59

Image 59

C h a p t e r 5

Installing the server and connecting the peripheral devices

In this chapter

Installing the server	60
Preparing the modem	61
Connecting peripherals to the server	65
Connecting the server to the ELAN	68
Connecting the server to the CLAN (optional)	71
Installing the Nortel software feature dongle	73
Connecting the server to power	75

1002rp Server Hardware Installation

Page 59

Image 59

Nortel Networks 1002rp manual Installing the server and connecting the peripheral devices, C h a p t e r, In this chapter

Contents

Document Number Document Version Standard 1002rp Server Hardware InstallationCallPilot ReleaseTrademarks Copyright 2006 Nortel NetworksCRYSTAL REPORTS is a trademark of Seagate Software Inc Japan VCCI statement Information for JapanJapan Denan statement があります。この場合には使用者が適切な対策を取るように要求されることがあります。 CallPilot StandardPublication history Publication history Installation is issued for general releaseOctober To connect the mouse, keyboard, and monitor to the server Task ListTo replace the front bezel after installation is complete To bring DC power and ground into the PDUCallPilot Task ListStandard 4 Power supply installation ContentsHow to get Help 3 Preparing for installationStandard EMC emission level protection for the 1002rp ServerIndex ContentsGetting Help from the Nortel Web site How to get HelpGetting Help over the phone from a Nortel Solutions Center C h a p t e rHow to get Help Getting Help from a specialist by using an Express Routing CodeGetting Help through a Nortel distributor or reseller C h a p t e r 1002rp server descriptionIn this chapter Introduction Server featuresServer dimensions and weight Environmental specifications G101750 Front panel features front view without the front bezelAlarm board 1002rp server description Rear panel diagramPCISBC ISA connectors connector connectors Overhead view of empty server showing PCI and ISA connectorsIntroduction Slot assignmentsSlot definition and slot numbering Slot 1002rp slot assignmentsCallPilot-assigned MeridianSlot a. On some CallPilot Manager screens, the CallPilot-assigned board label is displayed. This label corresponds to the slot number. For example, BRD12 refers to the board in slot ensure that the CallPilot network is inside your Network connectivityTo secure the CallPilot server from unauthorized access IntroductionSample network setup Meridian G250017 Sample network setup SuccessionTelephony LAN/Customer LAN 10/100BaseT or 100BaseT Embedded LAN 10BaseTMeridian 1 or Succession 1000 systems Switch connectivityCallPilot ELAN and CLAN network setup Network requirements Remote access connectivityIntroduction Supported peripheral devicesMaintenance Reference documentsInstallation and Configuration AdministrationCallPilot 1002rp server descriptionStandard In this chapter Preparing for installationInstallation overview C h a p t e rIntroduction Installation overviewInstallation checklist For a DC-powered server, set up the DC power source see Conventions for warnings Introduction Unpacking the 1002rp serverTo unpack the equipment What’s next? Introduction Removing the front bezel and server coverRisk of equipment damage To remove the front bezelWhat’s next? To remove the server coverIntroduction Inspecting the server interiorTo inspect the server interior THEN replace the server cover and proceed with the hardware installationSee “Installation checklist” on page Preparing for installationTo replace the front bezel after installation is complete DC wire gauge tables Power supply installationSafety precautions Installing the second power supply module AC or DCEquipment handling guidelines Safety precautionsSafety information Power supply installation Installing the second power supply module AC or DCAbout the power supply module AC versus DC systemsG101751 Power supply modulesWhat’s next? To install the power supply moduleIntroduction DC wire gauge tablesCabinet and module DC feed recommended wire gauge specifications AWG No Metric wire conversionIndustry standard Resistance at 20 CDC rack cabling Rack power and grounding 48 V DC power distribution rationale Introduction About the power distribution unitPDU power and grounding Multiple PDUsSingle PDU wiring diagram PDU terminal blocks and wiring diagramDC power input Introduction Bringing power and ground into the PDUTo bring DC power and ground into the PDU CallPilot Power supply installationStandard Connecting the server to the ELAN Installing the server and connecting the peripheral devicesInstalling the server Connecting peripherals to the serverIntroduction Installing the serverTo install the server Introduction Preparing the modemRequired equipment G101445 Modem DIP switchessetting To set the modem DIP switchesDefault switchWhat’s next? Installing the server and connecting the peripheral devicesStandardRear panel connectors Connecting peripherals to the serverTo connect the modem to the server To connect the mouse, keyboard, and monitor to the serverWhat’s next? Continue with “Connecting the server to the ELAN” on pageIntroduction Connecting the server to the ELANMedia Access Control address To connect the server to the ELANDANGER Risk of fire hazard 555-7101-210be connected to a CLAN continue with installing the softwarefeature dongle. See page What’s next?Introduction Connecting the server to the CLAN optionalTo connect the server to the CLAN Media Access Control addressWhat’s next? Continue with “Installing the Nortel software feature dongle” on pageSoftware Installing the Nortel software feature donglefeature key IntroductionContinue with “Connecting the server to power” on page To install the software feature dongleRequirements For installation, you require a Phillips No. 1 screwdriverBefore you begin Connecting the server to powerG250018 CallPilotserver To connect the 1002rp DC server to power To connect the 1002rp AC server to powerTo start the server A p p e n d i x A EMC emission level protection for the 1002rp ServerEMC emission level protection for the 1002rp Server Ferrites secured to an external cableNumerics IndexPage Page CallPilot IndexStandard Page CallPilot 1002rp Server Hardware Installation

Installing the server and connecting the peripheral devices

Installing the server

Preparing the modem

Connecting peripherals to the server

Connecting the server to the ELAN

Connecting the server to the CLAN (optional)

Installing the Nortel software feature dongle

Connecting the server to power