Manuals / Nortel Networks / Computer Equipment / Network Card

Nortel Networks 1002rp Then, replace the server cover and proceed with the hardware installation

Models: 1002rp

1 86

Page 43

October 2006	Preparing for installation
IF	THEN

you are satisfied that the 1002rp server has arrived at your site undamaged

replace the server cover and proceed with the hardware installation.

See “Installation checklist” on page 34.

Note: Do not reinstall the front bezel until the server is in its final location and the CallPilot installation is complete.

1002rp Server Hardware Installation

Page 43

Image 43

Nortel Networks 1002rp manual Then, replace the server cover and proceed with the hardware installation, October

Contents

Document Number Document Version Standard 1002rp Server Hardware InstallationCallPilot ReleaseTrademarks Copyright 2006 Nortel NetworksCRYSTAL REPORTS is a trademark of Seagate Software Inc Japan Denan statement Information for JapanJapan VCCI statement があります。この場合には使用者が適切な対策を取るように要求されることがあります。 CallPilot StandardPublication history October Installation is issued for general releasePublication history To connect the mouse, keyboard, and monitor to the server Task ListTo replace the front bezel after installation is complete To bring DC power and ground into the PDUStandard Task ListCallPilot 4 Power supply installation ContentsHow to get Help 3 Preparing for installationStandard EMC emission level protection for the 1002rp ServerIndex ContentsGetting Help from the Nortel Web site How to get HelpGetting Help over the phone from a Nortel Solutions Center C h a p t e rGetting Help through a Nortel distributor or reseller Getting Help from a specialist by using an Express Routing CodeHow to get Help In this chapter 1002rp server descriptionC h a p t e r Server dimensions and weight Server featuresIntroduction Environmental specifications Alarm board Front panel features front view without the front bezelG101750 1002rp server description Rear panel diagramPCISBC ISA connectors connector connectors Overhead view of empty server showing PCI and ISA connectorsSlot definition and slot numbering Slot assignmentsIntroduction Slot 1002rp slot assignmentsCallPilot-assigned MeridianSlot a. On some CallPilot Manager screens, the CallPilot-assigned board label is displayed. This label corresponds to the slot number. For example, BRD12 refers to the board in slot ensure that the CallPilot network is inside your Network connectivityTo secure the CallPilot server from unauthorized access IntroductionSample network setup Meridian G250017 Sample network setup SuccessionTelephony LAN/Customer LAN 10/100BaseT or 100BaseT Embedded LAN 10BaseTCallPilot ELAN and CLAN network setup Switch connectivityMeridian 1 or Succession 1000 systems Network requirements Remote access connectivityIntroduction Supported peripheral devicesMaintenance Reference documentsInstallation and Configuration AdministrationStandard 1002rp server descriptionCallPilot In this chapter Preparing for installationInstallation overview C h a p t e rInstallation checklist Installation overviewIntroduction For a DC-powered server, set up the DC power source see Conventions for warnings To unpack the equipment Unpacking the 1002rp serverIntroduction What’s next? Introduction Removing the front bezel and server coverRisk of equipment damage To remove the front bezelWhat’s next? To remove the server coverTo inspect the server interior Inspecting the server interiorIntroduction THEN replace the server cover and proceed with the hardware installationSee “Installation checklist” on page Preparing for installationTo replace the front bezel after installation is complete DC wire gauge tables Power supply installationSafety precautions Installing the second power supply module AC or DCSafety information Safety precautionsEquipment handling guidelines Power supply installation Installing the second power supply module AC or DCAbout the power supply module AC versus DC systemsG101751 Power supply modulesWhat’s next? To install the power supply moduleCabinet and module DC feed recommended wire gauge specifications DC wire gauge tablesIntroduction AWG No Metric wire conversionIndustry standard Resistance at 20 CDC rack cabling Rack power and grounding 48 V DC power distribution rationale Introduction About the power distribution unitPDU power and grounding Multiple PDUsDC power input PDU terminal blocks and wiring diagramSingle PDU wiring diagram To bring DC power and ground into the PDU Bringing power and ground into the PDUIntroduction Standard Power supply installationCallPilot Connecting the server to the ELAN Installing the server and connecting the peripheral devicesInstalling the server Connecting peripherals to the serverTo install the server Installing the serverIntroduction Required equipment Preparing the modemIntroduction G101445 Modem DIP switchessetting To set the modem DIP switchesDefault switchWhat’s next? Installing the server and connecting the peripheral devicesStandardRear panel connectors Connecting peripherals to the serverTo connect the modem to the server To connect the mouse, keyboard, and monitor to the serverWhat’s next? Continue with “Connecting the server to the ELAN” on pageIntroduction Connecting the server to the ELANMedia Access Control address To connect the server to the ELANDANGER Risk of fire hazard 555-7101-210be connected to a CLAN continue with installing the softwarefeature dongle. See page What’s next?Introduction Connecting the server to the CLAN optionalTo connect the server to the CLAN Media Access Control addressWhat’s next? Continue with “Installing the Nortel software feature dongle” on pageSoftware Installing the Nortel software feature donglefeature key IntroductionContinue with “Connecting the server to power” on page To install the software feature dongleRequirements For installation, you require a Phillips No. 1 screwdriverBefore you begin Connecting the server to powerserver CallPilotG250018 To connect the 1002rp DC server to power To connect the 1002rp AC server to powerTo start the server A p p e n d i x A EMC emission level protection for the 1002rp ServerEMC emission level protection for the 1002rp Server Ferrites secured to an external cableNumerics IndexPage Page Standard IndexCallPilot Page CallPilot 1002rp Server Hardware Installation

October 2006

Preparing for installation

replace the server cover and proceed with the hardware installation.

See “Installation checklist” on page 34.