1Standard Dtmf Operational Commands | Nortel Networks RTU-292

RTU-292 Operations Manual

Table 3-1Standard DTMF Operational Commands

These commands may be entered by the RTU-292 front panel keypad, or by the keypad of a connected telephone or by a telephone set wired to the Local Phone Option. See 3.7.6 for special instructions regarding the use of the front panel keypad to send DTMF Commands.

DTMF Command	Function
* #	Terminate the call.

* 0	Manual Keying Toggle.
	Press once to key; the next press will unkey, etc.
	To prevent simultaneous use of VOX and Manual Keying, if VOX was
	enabled when * 0 is first entered, it will be shut off.

* 1	VOX Toggle.
	If VOX is on, * 1 will turn it off. If VOX is off, * 1 will turn it on.

* 2	VMR Toggle.
	If VMR is on, * 2 will turn it off. If VMR is off, * 2 will turn it on.
	VMM-100 Option must be installed

* 3	Noise Reduction Toggle.
	If Noise Reduction is on, * 3 will turn it off. If it’s off, * 3 will turn it
	on. VMM-100 Option must be installed.
* 4	Security Mode Toggle.
	If Security Mode is on, * 4 will turn it off. If it’s off, * 4 will turn it on.
	Security Device Option must be installed (not currently available).
* 5	Page the Operator (make a call to the RTU-292 operator at the front
	panel keypad / handset).
* 6	Page the Local Phone Operator (this command can obviously made
	only by a connected telephone and not by the Local Phone).

* 7	Reserved for future use.

* 8	Radio Control Mode. (Requires optional radio control S/W.)
	Use this command to enter the Radio Control Mode (dipswitch SW1-3
	must also be ON to enable this mode). This mode enables DTMF
	control of a companion Motorola URC-200 radio. See Section 7.
	If the RTU-292 is in the Radio Control Mode, * # will return it to
	standard RS-232 control mode. See Table 7-6.

* 99	Enter the programming mode.
	If passwords are enabled, the user will be prompted for the system
	password and not allowed to enter the programming mode unless the
	password is correctly entered. See Table 3-2.

JPS Communications, Inc.

3-14

Image 54

Nortel Networks RTU-292 operation manual 1Standard Dtmf Operational Commands, Dtmf Command Function

Contents

JPS Communications, Inc JPS P/N Revision July Proprietary Statement Phone 919 Fax 919 Table of Contents RTU-292 Theory of Operation Front Panel Buttons and Indicators Schematic Diagrams List Of Figures List of Tables Glossary This page intentionally left blank Scope Description General Assemblies Main BoardTelephone Interface Radio Interface Power Supply SectionHandset/Speaker Interface DSP Module Equipment and Accessories Supplied Qty Part Number Options Optional Equipment Not Supplied RTU-292 Specifications General Unpacking and InspectionReshipment of Equipment Installation Overview Installation ConsiderationsFCC Part 68 Regulations 1RTU-292 Factory Default Settings Feature / Function Adjustment Default Setting DC Input Power Selection Power RequirementsInput Power Selection Line Voltage Selection Configuring the RTU-292 Programming Mode Setup ParametersSetting Telephone Send and Receive Levels Type of System Recommended Phone Line SettingsFactory default settings are indicated by an asterisk Telephone Send/Receive Levels VOX Sensitivity VOX HangtimeVOX Hangtime VOX Sensitivity Telephone Ring Volume Dial ModeDial Mode RX Line Input Impedance Full/Half Duplex Radio Control ModeSW1-3 Radio Control Off Disabled Enabled SW2-8 Full/Half Duplex Off Full Duplex 11Voice Prompts Enable Password Protection10Password Protection Voice Prompts Interconnect Information 12Local Phone Enable14TX Level Set-up Mode 13 Local Phone Ringthrough Pin Function Telephone Connection15J1 TEL Line RJ-11C Radio Connection Handset Connector 16P1-RADIO DB-9 Male17J7 Handset RJ12C Jack Terminal Block 18Terminal Block 6 Position Setting the Transmit Level Audio Level Setup and Adjustments19P2 RS-232 Connector DB-9 Male 5 RS-232 Connection Setting the Receive Level 10.1.2 RTU-292 Operations Manual Outline Dimensions Control and Connector Locations Location Of Internal Option Settings Internal Option Setting Details Audio Interface Wiring Diagram Interface Details Installation Checklist Options Installation and ConfigurationInstallation Checklist Front Panel CONTROLS, Indicators and Connectors Keypad Speaker Volume ControlPhones Volume Control TEL Line Buttons Audible Ring Button Speaker ButtonsAuto ANS Button KEY Pushbutton 4 J2 Local Phone Connector Rear Panel Connectors1 P1 Radio Connector 7 P1 AC Power Connector USE of the RTU-292 Speaker to Monitor Audio OperationOperation Overview Placing a Telephone Call Receiving a Telephone Call Using the Handset with the RadioConnecting the Radio to the Telephone Line Putting a Telephone Call on Hold Manual Phone Patch Procedure 8.18.2 8.5 8.38.4 8.6 Self Test Negative Acknowledge ErrorRemote KEY Automated Operation Radio Is Keyed Keyed Disconnecting DisconnectWaiting For Input Query Radio Is Unkeyed Unkeyed Caller Enters The Password if enabled Caller Dials The RTU-292RTU-292 Adapts To The Phone Line RTU-292 Enters the Command Mode Placing a Call in the Command ModeTerminating a Call Dtmf Control Commands Operating the RTU-292 from the Front Panel Keypad 1Standard Dtmf Operational Commands Dtmf Command Function 2Programming Mode Dtmf Commands RTU-292 Password Protection Inactivity Disconnect TimerCalling Timer Using the RTU-292 Speed Dial Feature Using the Speed Dial FeatureProgramming the Speed Dial Directory Factory Reset Speed Dial ResetOptional 4 Wire Operation Front Panel Buttons and Indicators Main BoardAudio BUS Arrangement Telephone Interface Circuits Telephone Send CircuitsTelephone Receive Circuits Receiver Input Amplifier Ring Detector and Tone RingerRadio Interface Circuits Transmitter Audio Output Microphone Circuit Dtmf DetectorFSK Modem Speaker and Headphone Circuits Noise Generator Audio DelayAdaptive Hybrid Peak Detector DC Power Supply Power SupplyAC Power Supply 8 CPU Prompt Tone Generator Option Interface BoardVoice Prompt Option Speech Processor Interface Circuitry Local Phone OptionVoice Prompt Software DIAL/BUSY Generators RS-232 Remote Control Overview Commands Sent to the RTU-292 1Command Summary Null Command Auto Answer CommandAudible Ring Command Date Command Dial Command Disconnect Command Dtmf Command Handset Phone Command Handset Radio Command Speaker Phone Command Speaker Radio Command Speed Dial Command SD nnALL num.? CR Tel-Line Phone Command Tel-Line Radio Command Time Command Software Version Command Status Returned from the RTU-292 Response Summary Null Response Auto Answer ResponseCall Starting Response Dial Response Disconnect ResponseDtmf Response Elapsed Time Response Handset Phone ResponseHandset Radio Response Speaker Phone Response Speaker Radio Response Speed Dial Response Tel-Line Phone ResponseTel-Line Radio Response Time/Date Response Version Response Call Progress Responses from the RTU-292 Response Error CodesResponse Error Codes Call Progress Responses Performance Testing Preventive MaintenanceRepair or Replacement Alignment Hybrid Balance Measurement Hybrid Balance Test Set-Up Main Hybrid Test Procedure Alternate Hybrid Test Procedure VOX Sensitivity Test Set-Up VOX Test Procedure VOX Sensitivity Measurement Fault Analysis Replaceable Parts List Description Description Reference Designator RTU-292 Operations Manual Reference Designator Special Software Versions RTU-292 Options SW1-6 Voice Prompts Off Disabled Enabled Installation and ConfigurationVoice Prompts Enable Operation Voice Prompt Option Installation SW1-7 Local Phone Off Disabled Enabled Local Phone Option Installation and ConfigurationLocal Phone Enable SW1-8 Ringthrough Off Disabled Enabled 5Local Phone Dtmf Commands Local Phone Option Operation VMM-100 Hardware VMM-100 DSP SectionVMM-100 Analog Interface VMR Algorithm VMM-100 Installation and ConfigurationVMM-100 Software Noise Reduction Algorithm VMM-100 Option Installation VMM-100 Specifications Environmental VMM-100 I/O Connector Information P9 VMM-100 Switch Functions Dtmf Access Option After the Call Begins Squelch Break Access Option RTU-292 Prompts for Confirmation Call Logging Option Setting The TimeSetting The Date Checking The Time And Date Radio Control Option Controlling the Radio VIA the RTU-292 Front Panel Keypad 9DTMF Radio Control Commands Command Followed By Command Description Schematic Diagrams Blank Index Environmental Self Test Speech Processor