10. Multi-unit Operation

55
10Multi-unit OperationAdditional U nits
10.1 Operating additional units

10.1.1 Additional cordless handsets

Up to 6 cordless handsets can be registered to the base
unit. Additional cordless handsets will give you the
freedom to, for example, have an intercom call with
another cordless handset while a third cordless handset
is on an outside call.
Important:
LThe additional cordless handset model
recommended for use with this unit is noted on
page 9. If other model cordless handset is used,
certain operations (cordless handset settings,
base unit settings, etc.) may not be available.
10.2 Registering a cordless handset to a base unit
The included cordless handset and base unit are
preregistered. If for some reason the cordless handset is
not registered to the base unit (for example, w flashes
even when the cordless handset is near the base unit),
register the cordless handset manually.
After purchasing an additional cordless handset, register
it to the base unit. Ensure that the additional cordless
handset is switched ON. If it is not ON, press and hold
{ih} for few seconds to turn the cordless handset ON.
1{j/OK} i “Handset Setup” i {>}
2“Registration” i {>}
3“Register H.set” i {>}
4Press and hold {LOCATOR} on the base unit for
about 3 seconds, until the registration tone sounds.
LAfter pressing {LOCATOR}, the rest of this
procedure must be completed within 1 minute.
5Wait until “Enter Base PIN” is displayed, then
enter the base unit PIN (default: “0000”), then press
{j/OK}.
LIf you forget your PIN, consult your nearest
Panasonic service centre.
LWhen the cordless handset has been registered
successfully, w will stop flashing. If keytones are
turned ON (page 52), a confirmation tone will be
heard.
Note:
LCharge the batteries of your additional cordless
handset for about 7 hours before initial use.

10.2.1 Cancelling a cordless handset

A maximum of 6 cordless handsets can be registered to
a base unit. A cordless handset can cancel its own
registration (or the registration of another cordless
handset) that is stored in the base unit. This will allow the
base unit to forget the cordless handset.
1{j/OK} i “Base Unit Setup” i {>}
2Enter “335”.
3“Cancel Handset” i {>}
LThe numbers of all cordless handsets registered
to the base unit are displayed.
4Select the cordless handset(s) you want to cancel,
by pressing the desired cordless handset number.
LThe selected cordless handset number(s) will
flash.
LTo cancel a selected cordless handset number,
press the number again. The numbe r will stop
flashing.
5{j/OK}
6“Yes” i {>} i {ih}

10.2.2 Increasing the range of the base unit

You can increase the signal range of the base unit by
using a DECT repeater. Please use only Panasonic
DECT repeater. See page 9 for accessory information.
Important:
LBefore registering the repeater to this base unit,
you must turn the repeater mode ON.
LDo not use more than one repeater at a time.
Setting the repeater mode
1. {j/OK} i “Base Unit Setup” i {>}
2. “Other Options” i {>}
3. “Repeater Mode” i {>}
4. “On” or “Off” i {>} i {ih}
Note:
LAfter turning repeater mode ON or OFF, w may f las h
on the cordless handset momentarily. This is normal.
The cordless handset can be used once w stops
flashing.
Other Features
10.3 Intercom
Intercom calls can be made between a cordless handset
and the base unit, and between 2 cordless handsets.
You can page all cordless handsets at once from the
base unit.

10.3.1 Making intercom calls

With the cordless handset
1{INT}
2To page the base unit, press {0}.
To page another cordless handset, press the
desired cordless handset number.
LThe base unit or the destination cordless
handset will beep (be paged) for 1 minute.
LTo stop paging, press {ih}.
3When the paged party answers, talk into the
cordless handset.
4To end the intercom call, press {ih}.