Settings Battery Charge, Battery strength | Panasonic KX-TCD961CXB

KX-TCD961CXB(06~16) 99.12.3 2:04 PM Page 12

Settings

Battery Charge

At the time of shipment, the batteries are not charged. To charge, place the handset on the base unit. Please charge the batteries for about 4 hours before initial use.

•The charge indicator () lights.

OR

Charge Indicator ()

Battery strength

You can check the present battery strength on the display.

Battery strength

Fully charged

Medium

Low

No power

Battery icon

(Flashing)

Recharge

When “” flashes or the unit beeps every 15 seconds, recharge the batteries.

Battery information

After your Panasonic batteries are fully charged:

Operation	Approx. Ni-Cd battery life (included)	Approx. Ni-MH battery life (option)*

While in use (Talk)	Up to about 6 hours	Up to about 12 hours

While not in use (Stand-By)	Up to about 65 hours	Up to about 130 hours

•Battery life may vary depending on usage conditions and ambient temperature.

•Clean the handset and the base unit charge contacts with a soft, dry cloth once a month. Clean more often if the unit is subject to grease, dust or high humidity. Otherwise the batteries may not charge properly.

•If the batteries are fully charged, you do not have to place the handset on the base unit until

“” flashes. This will maximize the battery life.

•The batteries cannot be overcharged.

*Nickel metal hydride (Ni-MH) rechargeable batteries (AAA size) are available.

When you replace the batteries, you must program the battery type selection (see page 57).

•Read “Important Notice Concerning the Correct Use and Charging of Ni-Cd (Ni-MH) Batteries” on page 58.

12

Image 12

Panasonic KX-TCD961CXB operating instructions Settings Battery Charge, Battery strength, Recharge, Battery information

Contents

Operating Instructions Charge the batteries for about 4 hours before initial use Battery p One Three Handset Cover p Belt Clip p Before Initial UseSerial No Date of purchase Name and address of dealer Battery Charge For Best PerformanceBase Unit Location Obstructions such as walls Contents Selecting the Stand-by Mode Correct Use and Charging Select Button p Skip Button Charge Indicator Location of ControlsBase unit New Message Button Handset 13, 18, 24, 27Tone Button Displays Base unit displayMessages have been recorded Recording time is set to greeting only p Display shows all possible configurations IconsCharacters Is pressed while dialing Settings Installing the Batteries in the HandsetUsing the Belt Clip To remove the belt clip Connections Telephone Settings Battery Charge Battery strengthBattery information Recharge Turning the Power on Selecting the Dialing ModePress firmly Press Settings Selecting the Handset Ringer Volume/Pattern Ringer volumeIUU F23 Selecting the Base Unit Ringer Volume/Pattern 22u223U Preparing the Answering System Selecting the Voice Guidance LanguageTo select to Slovakian, press To select to Czech, press Greeting Message Function item Time pTo set the greeting monitor Function p Time and Day Adjustment To check the time/dayPress repeatedly to set the day Minutes Greeting onlyRecording time Setting the Greeting Monitor Function Press Toll Saver When set to AutoCurrent setting, 1 or 2, is displayed on the base unit Selecting the Number of Rings To select the receiver volume Making CallsI2345678 00 00 Answering Calls To redial the last number dialedTo redial after confirming the numbers in redial memory To turn the handset ringer off temporarily Speed Dialer Storing Phone Numbers in MemoryDialing a Stored Number To erase a stored number Intercom Paging the base unit from the handsetPaging the handset from the base unit Handset locator Special Features How to Use the Pause FeatureSetting the pause timing To select 5 seconds, press To select 3 seconds, press Press Setting the Key Lock Using the Recall FeatureFor Rotary or Pulse Service Users To cancel the key lock Summary of Programmable Functions Setting the Password F5oF5o - - o 5o - - o Setting the Direct Call Mode To turn OFF the direct call modeDirect Call F42 To turn OFF the call prohibition mode Call ProhibitionF4 Io F4 IO0 To cancel the call restricted handsets To cancel the call restriction numbersCall Restriction I23456 Selecting the Talk Mode Display Press G or F to select the desired settingF32U During a conversation, the display will be as follows Automatic Route Selection Storing the Carrier Code/Area Codes To store the carrier codeTo store the area codes Other Programmable Settings F2 iF25 F26 Clearing the Settings in Memory Function Setting the Unit to Answer Calls Automatic Answering OperationMonitoring incoming calls Press Answer on to turn on the answering system Flash Memory Message Backup Listening to MessagesListening to only new messages Listening to all recorded messages Erasing Messages Recording a Memo MessageErasing a specific message Erasing all messages Remote Operation from a Touch Tone Phone Summary of remote operation Canceling the remote operation To cancel, reprogram a new remote codeDisplay goes out Direct commands Direct Remote Operation Remote Operation from a Touch Tone Phone To continue the remote operationTurning on the answering system Skipping the greeting message Remote Operation with the Handset Help menuMenu Recording your telephone conversation using the handset Continue your conversation When finished, press thenRemote Operation with the Handset During a conversation, press Then For Optional Multi-Unit Users Operating More than One HandsetOperating More than One Base Unit Registration F7 iRegistering a Handset in the Base Unit Selecting the Base Unit Access Automatic base unit accessSpecified base unit access I000 Registration Canceling a Handset Canceling a base unitF70 i2 Selecting the Stand-by Mode Display Bell SelectionF3 i0 Iu2 Bell Selection Selecting first handsetSelecting all handsets Enter the handset number you want to ring Intercom between the Handsets and the Base Unit Paging all the handsets from the base unit All pagingPaging a handset from the base unit Individual paging Page, then press Handset When the unit rings, press to answer 00 00 0Intercom Intercom between Handsets Handset 1 Press I N T Enter the desired handset number Transferring a call using the intercom Transferring a Call from One Handset to AnotherTransferring a call without the intercom Setting the Call Waiting Tone F24Intercom Conference Press Press G or F until F24 is displayed Press O K Selecting the battery type Battery replacementAfter replacement Replacing the Batteries Replacing the Batteries Cordless Telephone Problem Remedy Before Requesting Help Problem Remedy Before Requesting HelpDoes not function Answering System Problem Remedy Base unit, it suddenly stops Use indicator You cannot operate the answeringSystem at the base unit System from a touch tone phone General Problem Remedy Safety Instructions SafetyInstallations Environment Placement Lightning surge KX-TCD961CXB57~68 99.12.3 222 PM Term Definitions Obchodní oddélení Panasonic Czech Republic, s.r.o Krakovská 9, 110 00, Praha 1, Èeská republikaVýrobní závod PQQX12234ZA-UK WU1299NR0