General Problem Remedy | Panasonic KX-TCD961CXB specs

KX-TCD961CXB(57~68) 99.12.3 2:22 PM Page 63

General

		Problem		Remedy

The unit does not work.				• Turn the power ON (p. 13).
				• Check the settings (p. 10–15).
				• Charge the batteries fully (p. 12).
				• Clean the charge contacts and charge again (p. 12).
				• Unplug the AC adaptor and turn the power OFF to
				reset. Plug in the AC adaptor and turn the power ON.
				Then try again.
				• The handset has been canceled or has not been
				registered. Register the handset (p. 48).
				• Re-install the handset batteries and try again.

You cannot program function items such				• Programming is not possible while the unit is in the
as the time/day adjustment (p. 19).				talk or intercom mode.
				• Move closer to the base unit.

The battery strength is not displayed				• Check that the battery type selection is correct
correctly.				(p. 57).

“		” flashes or the unit beeps every		• Charge the batteries fully (p. 12).
“		” flashes or the unit beeps every		• Charge the batteries fully (p. 12).
15 seconds.

You charged the batteries fully, but				• Clean the charge contacts and charge again (p. 12).
“		” flashes.		• Install new batteries (p. 57, 58).
“		” flashes.		• Install new batteries (p. 57, 58).

The charge indicator (			) light never	• This is normal.
goes out while charging.

Useful Information Chapter 6

63

Image 63

Panasonic KX-TCD961CXB operating instructions General Problem Remedy

Contents

Charge the batteries for about 4 hours before initial use Operating Instructions Name and address of dealer Battery p One Three Handset Cover p Belt Clip pBefore Initial Use Serial No Date of purchase Obstructions such as walls Battery ChargeFor Best Performance Base Unit Location Contents Correct Use and Charging Selecting the Stand-by Mode New Message Button Select Button p Skip Button Charge IndicatorLocation of Controls Base unit Handset 13, 18, 24, 27Tone Button Recording time is set to greeting only p DisplaysBase unit display Messages have been recorded Is pressed while dialing Display shows all possible configurationsIcons Characters To remove the belt clip SettingsInstalling the Batteries in the Handset Using the Belt Clip Telephone Connections Recharge Settings Battery ChargeBattery strength Battery information Press Turning the Power onSelecting the Dialing Mode Press firmly F23 Settings Selecting the Handset Ringer Volume/PatternRinger volume IUU Selecting the Base Unit Ringer Volume/Pattern 22u223U Preparing the Answering System Selecting the Voice Guidance LanguageTo select to Slovakian, press To select to Czech, press Greeting Message Function p Function itemTime p To set the greeting monitor Time and Day Adjustment To check the time/dayPress repeatedly to set the day Minutes Greeting onlyRecording time Selecting the Number of Rings Setting the Greeting Monitor FunctionPress Toll Saver When set to Auto Current setting, 1 or 2, is displayed on the base unit 00 00 To select the receiver volumeMaking Calls I2345678 To turn the handset ringer off temporarily Answering CallsTo redial the last number dialed To redial after confirming the numbers in redial memory To erase a stored number Speed DialerStoring Phone Numbers in Memory Dialing a Stored Number Intercom Paging the base unit from the handsetPaging the handset from the base unit Handset locator To select 5 seconds, press To select 3 seconds, press Press Special FeaturesHow to Use the Pause Feature Setting the pause timing To cancel the key lock Setting the Key LockUsing the Recall Feature For Rotary or Pulse Service Users Summary of Programmable Functions 5o - - o Setting the PasswordF5o F5o - - o F42 Setting the Direct Call ModeTo turn OFF the direct call mode Direct Call F4 IO0 To turn OFF the call prohibition modeCall Prohibition F4 Io I23456 To cancel the call restricted handsetsTo cancel the call restriction numbers Call Restriction During a conversation, the display will be as follows Selecting the Talk Mode DisplayPress G or F to select the desired setting F32U Automatic Route Selection Storing the Carrier Code/Area Codes To store the carrier codeTo store the area codes F26 Other Programmable SettingsF2 i F25 Function Clearing the Settings in Memory Press Answer on to turn on the answering system Setting the Unit to Answer CallsAutomatic Answering Operation Monitoring incoming calls Listening to all recorded messages Flash Memory Message BackupListening to Messages Listening to only new messages Erasing all messages Erasing MessagesRecording a Memo Message Erasing a specific message Summary of remote operation Remote Operation from a Touch Tone Phone Canceling the remote operation To cancel, reprogram a new remote codeDisplay goes out Direct Remote Operation Direct commands Skipping the greeting message Remote Operation from a Touch Tone PhoneTo continue the remote operation Turning on the answering system Remote Operation with the Handset Help menuMenu During a conversation, press Then Recording your telephone conversation using the handsetContinue your conversation When finished, press then Remote Operation with the Handset For Optional Multi-Unit Users Operating More than One HandsetOperating More than One Base Unit Registration F7 iRegistering a Handset in the Base Unit I000 Selecting the Base Unit AccessAutomatic base unit access Specified base unit access Registration Canceling a Handset Canceling a base unitF70 i2 Iu2 Selecting the Stand-by Mode DisplayBell Selection F3 i0 Enter the handset number you want to ring Bell SelectionSelecting first handset Selecting all handsets Page, then press Intercom between the Handsets and the Base UnitPaging all the handsets from the base unit All paging Paging a handset from the base unit Individual paging Handset 1 Press I N T Enter the desired handset number Handset When the unit rings, press to answer00 00 0 Intercom Intercom between Handsets Transferring a call using the intercom Transferring a Call from One Handset to AnotherTransferring a call without the intercom Press Press G or F until F24 is displayed Press O K Setting the Call Waiting ToneF24 Intercom Conference Replacing the Batteries Selecting the battery typeBattery replacement After replacement Replacing the Batteries Before Requesting Help Cordless Telephone Problem Remedy Problem Remedy Before Requesting HelpDoes not function Answering System Problem Remedy System from a touch tone phone Base unit, it suddenly stops Use indicatorYou cannot operate the answering System at the base unit General Problem Remedy Placement Safety InstructionsSafety Installations Environment Lightning surge KX-TCD961CXB57~68 99.12.3 222 PM Term Definitions PQQX12234ZA-UK WU1299NR0 Obchodní oddélení Panasonic Czech Republic, s.r.oKrakovská 9, 110 00, Praha 1, Èeská republika Výrobní závod