F70 i2, Registration Canceling a Handset | Panasonic KX-TCD961CXB

KX-TCD961CXB(47~56) 99.12.3 2:20 PM Page 50

Registration

Canceling a Handset

Each handset can cancel itself or another handset.

1 Press then I N T . 2 Press 7 .

3Enter the base unit password (p. 29).

•The current registered handset number(s) is/are displayed.

Ex. Handset 1, 2, 3, 4, 5 and 6 are registered.

7 i23456

4Enter the handset number(s) you want to cancel.

•The selected handset number(s) flash(es). Ex. Handset 6 is canceled.

7i23456

•If you misdial, press the number(s) again.

5 Press .

•A confirmation tone sounds and the display will return to the stand-by mode.

Canceling a base unit

If another handset is out of range and/or its power is OFF when “Canceling a Handset”, the previous base unit number will still remain in the canceled handset. Therefore, you need to cancel the base unit registered in the canceled handset.

1 Press .

2Press G or F until “F70” is displayed.

3Press O K .

4Enter the handset password (p. 29).

•Registered base number(s) is(are) displayed.

Ex. Registered base units: 1, 2 and 4

F70 i2 4

5Press the canceling base unit number

1to 4 .

•The selected base unit number flashes.

6Press .

•A confirmation tone sounds and the display will return to the stand-by mode.

50

Image 50

Panasonic KX-TCD961CXB operating instructions F70 i2, Registration Canceling a Handset, Canceling a base unit

Contents

Operating Instructions Charge the batteries for about 4 hours before initial use Serial No Date of purchase Battery p One Three Handset Cover p Belt Clip pBefore Initial Use Name and address of dealer Base Unit Location Battery ChargeFor Best Performance Obstructions such as walls Contents Selecting the Stand-by Mode Correct Use and Charging Base unit Select Button p Skip Button Charge IndicatorLocation of Controls New Message Button Tone Button Handset13, 18, 24, 27 Messages have been recorded DisplaysBase unit display Recording time is set to greeting only p Characters Display shows all possible configurationsIcons Is pressed while dialing Using the Belt Clip SettingsInstalling the Batteries in the Handset To remove the belt clip Connections Telephone Battery information Settings Battery ChargeBattery strength Recharge Press firmly Turning the Power onSelecting the Dialing Mode Press IUU Settings Selecting the Handset Ringer Volume/PatternRinger volume F23 23U Selecting the Base Unit Ringer Volume/Pattern22u2 To select to Slovakian, press To select to Czech, press Preparing the Answering SystemSelecting the Voice Guidance Language Greeting Message To set the greeting monitor Function itemTime p Function p Press repeatedly to set the day Time and Day AdjustmentTo check the time/day Recording time MinutesGreeting only Current setting, 1 or 2, is displayed on the base unit Setting the Greeting Monitor FunctionPress Toll Saver When set to Auto Selecting the Number of Rings I2345678 To select the receiver volumeMaking Calls 00 00 To redial after confirming the numbers in redial memory Answering CallsTo redial the last number dialed To turn the handset ringer off temporarily Dialing a Stored Number Speed DialerStoring Phone Numbers in Memory To erase a stored number Paging the handset from the base unit Handset locator IntercomPaging the base unit from the handset Setting the pause timing Special FeaturesHow to Use the Pause Feature To select 5 seconds, press To select 3 seconds, press Press For Rotary or Pulse Service Users Setting the Key LockUsing the Recall Feature To cancel the key lock Summary of Programmable Functions F5o - - o Setting the PasswordF5o 5o - - o Direct Call Setting the Direct Call ModeTo turn OFF the direct call mode F42 F4 Io To turn OFF the call prohibition modeCall Prohibition F4 IO0 Call Restriction To cancel the call restricted handsetsTo cancel the call restriction numbers I23456 F32U Selecting the Talk Mode DisplayPress G or F to select the desired setting During a conversation, the display will be as follows Automatic Route Selection To store the area codes Storing the Carrier Code/Area CodesTo store the carrier code F25 Other Programmable SettingsF2 i F26 Clearing the Settings in Memory Function Monitoring incoming calls Setting the Unit to Answer CallsAutomatic Answering Operation Press Answer on to turn on the answering system Listening to only new messages Flash Memory Message BackupListening to Messages Listening to all recorded messages Erasing a specific message Erasing MessagesRecording a Memo Message Erasing all messages Remote Operation from a Touch Tone Phone Summary of remote operation Display goes out Canceling the remote operationTo cancel, reprogram a new remote code Direct commands Direct Remote Operation Turning on the answering system Remote Operation from a Touch Tone PhoneTo continue the remote operation Skipping the greeting message Menu Remote Operation with the HandsetHelp menu Remote Operation with the Handset Recording your telephone conversation using the handsetContinue your conversation When finished, press then During a conversation, press Then Operating More than One Base Unit For Optional Multi-Unit UsersOperating More than One Handset Registering a Handset in the Base Unit RegistrationF7 i Specified base unit access Selecting the Base Unit AccessAutomatic base unit access I000 F70 i2 Registration Canceling a HandsetCanceling a base unit F3 i0 Selecting the Stand-by Mode DisplayBell Selection Iu2 Selecting all handsets Bell SelectionSelecting first handset Enter the handset number you want to ring Paging a handset from the base unit Individual paging Intercom between the Handsets and the Base UnitPaging all the handsets from the base unit All paging Page, then press Intercom Intercom between Handsets Handset When the unit rings, press to answer00 00 0 Handset 1 Press I N T Enter the desired handset number Transferring a call without the intercom Transferring a call using the intercomTransferring a Call from One Handset to Another Intercom Conference Setting the Call Waiting ToneF24 Press Press G or F until F24 is displayed Press O K After replacement Selecting the battery typeBattery replacement Replacing the Batteries Replacing the Batteries Cordless Telephone Problem Remedy Before Requesting Help Does not function Problem RemedyBefore Requesting Help Answering System Problem Remedy System at the base unit Base unit, it suddenly stops Use indicatorYou cannot operate the answering System from a touch tone phone General Problem Remedy Installations Environment Safety InstructionsSafety Placement Lightning surge KX-TCD961CXB57~68 99.12.3 222 PM Term Definitions Výrobní závod Obchodní oddélení Panasonic Czech Republic, s.r.oKrakovská 9, 110 00, Praha 1, Èeská republika PQQX12234ZA-UK WU1299NR0