Replacing the Batteries, After replacement | Panasonic KX-TCD961CXB

KX-TCD961CXB(57~68) 99.12.3 2:22 PM Page 57

Replacing the Batteries

Selecting the battery type

Three Nickel cadmium (Ni-Cd) batteries are included with this unit. Nickel metal hydride (Ni-MH) rechargeable batteries can also be used. If you replace the batteries with Ni-MH batteries, you must set the battery type selection to “1”, or the battery strength will not be displayed correctly. The factory preset is “0” (Ni-Cd).

1 Press .

2Press G or F until “F33” is displayed.

3Press O K .

4	To select Ni-MH batteries, press		1 .
	OR
	To select Ni-Cd batteries, press		0 .
5	Press	.

• A confirmation tone sunds and the display will return to the stand-by mode.

• Incorrect battery type selection may shorten battery life.

Battery replacement

If “ ” flashes after a few telephone calls even when the handset batteries have been fully charged, it is time to replace the batteries with new ones. Remember to charge the new batteries

after replacement.

1 Turn the power OFF to prevent memory loss (p. 13). Remove the cover by sliding while pressing in the direction of the arrow, then take out the batteries.

2Replace the batteries with new ones as shown.

•When you finish, close the handset cover and turn

the power ON (p. 13).

3 Be sure to charge the new batteries fully in order to display the battery icon correctly (p. 12).

Ni-Cd battery: For about 4 hours.

Ni-MH battery: For about 8 hours.

•Discard defective batteries as soon as possible. Defective batteries may leak into the unit.

•Please use only Panasonic P-03H or P-P03S batteries.

•If the rechargeable batteries are not inserted correctly, the handset will not work.

•Nickel metal hydride (Ni-MH) rechargeable batteries (AAA size) are available. Please use only Panasonic HHR-P03H batteries.

•Please return the rechargeable batteries to your sales shop at the end of their useful life.

Useful Information Chapter 6

57

Image 57

Panasonic KX-TCD961CXB Replacing the Batteries, Selecting the battery type, Battery replacement, After replacement

Contents

Charge the batteries for about 4 hours before initial use Operating Instructions Before Initial Use Battery p One Three Handset Cover p Belt Clip pSerial No Date of purchase Name and address of dealer For Best Performance Battery ChargeBase Unit Location Obstructions such as walls Contents Correct Use and Charging Selecting the Stand-by Mode Location of Controls Select Button p Skip Button Charge IndicatorBase unit New Message Button Handset 13, 18, 24, 27Tone Button Base unit display DisplaysMessages have been recorded Recording time is set to greeting only p Icons Display shows all possible configurationsCharacters Is pressed while dialing Installing the Batteries in the Handset SettingsUsing the Belt Clip To remove the belt clip Telephone Connections Battery strength Settings Battery ChargeBattery information Recharge Selecting the Dialing Mode Turning the Power onPress firmly Press Ringer volume Settings Selecting the Handset Ringer Volume/PatternIUU F23 Selecting the Base Unit Ringer Volume/Pattern 22u223U Preparing the Answering System Selecting the Voice Guidance LanguageTo select to Slovakian, press To select to Czech, press Greeting Message Time p Function itemTo set the greeting monitor Function p Time and Day Adjustment To check the time/dayPress repeatedly to set the day Minutes Greeting onlyRecording time Press Toll Saver When set to Auto Setting the Greeting Monitor FunctionCurrent setting, 1 or 2, is displayed on the base unit Selecting the Number of Rings Making Calls To select the receiver volumeI2345678 00 00 To redial the last number dialed Answering CallsTo redial after confirming the numbers in redial memory To turn the handset ringer off temporarily Storing Phone Numbers in Memory Speed DialerDialing a Stored Number To erase a stored number Intercom Paging the base unit from the handsetPaging the handset from the base unit Handset locator How to Use the Pause Feature Special FeaturesSetting the pause timing To select 5 seconds, press To select 3 seconds, press Press Using the Recall Feature Setting the Key LockFor Rotary or Pulse Service Users To cancel the key lock Summary of Programmable Functions F5o Setting the PasswordF5o - - o 5o - - o To turn OFF the direct call mode Setting the Direct Call ModeDirect Call F42 Call Prohibition To turn OFF the call prohibition modeF4 Io F4 IO0 To cancel the call restriction numbers To cancel the call restricted handsetsCall Restriction I23456 Press G or F to select the desired setting Selecting the Talk Mode DisplayF32U During a conversation, the display will be as follows Automatic Route Selection Storing the Carrier Code/Area Codes To store the carrier codeTo store the area codes F2 i Other Programmable SettingsF25 F26 Function Clearing the Settings in Memory Automatic Answering Operation Setting the Unit to Answer CallsMonitoring incoming calls Press Answer on to turn on the answering system Listening to Messages Flash Memory Message BackupListening to only new messages Listening to all recorded messages Recording a Memo Message Erasing MessagesErasing a specific message Erasing all messages Summary of remote operation Remote Operation from a Touch Tone Phone Canceling the remote operation To cancel, reprogram a new remote codeDisplay goes out Direct Remote Operation Direct commands To continue the remote operation Remote Operation from a Touch Tone PhoneTurning on the answering system Skipping the greeting message Remote Operation with the Handset Help menuMenu Continue your conversation When finished, press then Recording your telephone conversation using the handsetRemote Operation with the Handset During a conversation, press Then For Optional Multi-Unit Users Operating More than One HandsetOperating More than One Base Unit Registration F7 iRegistering a Handset in the Base Unit Automatic base unit access Selecting the Base Unit AccessSpecified base unit access I000 Registration Canceling a Handset Canceling a base unitF70 i2 Bell Selection Selecting the Stand-by Mode DisplayF3 i0 Iu2 Selecting first handset Bell SelectionSelecting all handsets Enter the handset number you want to ring Paging all the handsets from the base unit All paging Intercom between the Handsets and the Base UnitPaging a handset from the base unit Individual paging Page, then press 00 00 0 Handset When the unit rings, press to answerIntercom Intercom between Handsets Handset 1 Press I N T Enter the desired handset number Transferring a call using the intercom Transferring a Call from One Handset to AnotherTransferring a call without the intercom F24 Setting the Call Waiting ToneIntercom Conference Press Press G or F until F24 is displayed Press O K Battery replacement Selecting the battery typeAfter replacement Replacing the Batteries Replacing the Batteries Before Requesting Help Cordless Telephone Problem Remedy Problem Remedy Before Requesting HelpDoes not function Answering System Problem Remedy You cannot operate the answering Base unit, it suddenly stops Use indicatorSystem at the base unit System from a touch tone phone General Problem Remedy Safety Safety InstructionsInstallations Environment Placement Lightning surge KX-TCD961CXB57~68 99.12.3 222 PM Term Definitions Krakovská 9, 110 00, Praha 1, Èeská republika Obchodní oddélení Panasonic Czech Republic, s.r.oVýrobní závod PQQX12234ZA-UK WU1299NR0