Connections, Telephone | Panasonic KX-TCD961CXB instruction

KX-TCD961CXB(06~16) 99.12.3 2:04 PM Page 11

Connections

Plug in the AC adaptor cord and the telephone line cord to the bottom of the unit. Then connect the cords as shown.

Fasten the cords to prevent them from

being disconnected.

Hooks

To Power Outlet

(AC 230 V, 50 Hz)

8V	AC Adaptor

Chapter 1 Preparation

Telephone	AC	To Single-Line
		Telephone Jack
Line Cord	Adaptor

		Telephone Line Cord

•USE ONLY WITH Panasonic AC ADAPTOR KX-TCA11CE.

•Be careful not to confuse the telephone line jack with the AC adaptor jack on the base unit. If connected improperly, the base unit will not work and damage may occur.

•The AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)

•The unit will not work during a power failure. We recommend you connect a standard telephone on the same line for power protection.

Page 11

Image 11

Panasonic KX-TCD961CXB operating instructions Connections, Telephone

Contents

Charge the batteries for about 4 hours before initial use Operating Instructions Name and address of dealer Battery p One Three Handset Cover p Belt Clip pBefore Initial Use Serial No Date of purchase Obstructions such as walls Battery ChargeFor Best Performance Base Unit Location Contents Correct Use and Charging Selecting the Stand-by Mode New Message Button Select Button p Skip Button Charge IndicatorLocation of Controls Base unit Tone Button Handset13, 18, 24, 27 Recording time is set to greeting only p DisplaysBase unit display Messages have been recorded Is pressed while dialing Display shows all possible configurationsIcons Characters To remove the belt clip SettingsInstalling the Batteries in the Handset Using the Belt Clip Telephone Connections Recharge Settings Battery ChargeBattery strength Battery information Press Turning the Power onSelecting the Dialing Mode Press firmly F23 Settings Selecting the Handset Ringer Volume/PatternRinger volume IUU 23U Selecting the Base Unit Ringer Volume/Pattern22u2 To select to Slovakian, press To select to Czech, press Preparing the Answering SystemSelecting the Voice Guidance Language Greeting Message Function p Function itemTime p To set the greeting monitor Press repeatedly to set the day Time and Day AdjustmentTo check the time/day Recording time MinutesGreeting only Selecting the Number of Rings Setting the Greeting Monitor FunctionPress Toll Saver When set to Auto Current setting, 1 or 2, is displayed on the base unit 00 00 To select the receiver volumeMaking Calls I2345678 To turn the handset ringer off temporarily Answering CallsTo redial the last number dialed To redial after confirming the numbers in redial memory To erase a stored number Speed DialerStoring Phone Numbers in Memory Dialing a Stored Number Paging the handset from the base unit Handset locator IntercomPaging the base unit from the handset To select 5 seconds, press To select 3 seconds, press Press Special FeaturesHow to Use the Pause Feature Setting the pause timing To cancel the key lock Setting the Key LockUsing the Recall Feature For Rotary or Pulse Service Users Summary of Programmable Functions 5o - - o Setting the PasswordF5o F5o - - o F42 Setting the Direct Call ModeTo turn OFF the direct call mode Direct Call F4 IO0 To turn OFF the call prohibition modeCall Prohibition F4 Io I23456 To cancel the call restricted handsetsTo cancel the call restriction numbers Call Restriction During a conversation, the display will be as follows Selecting the Talk Mode DisplayPress G or F to select the desired setting F32U Automatic Route Selection To store the area codes Storing the Carrier Code/Area CodesTo store the carrier code F26 Other Programmable SettingsF2 i F25 Function Clearing the Settings in Memory Press Answer on to turn on the answering system Setting the Unit to Answer CallsAutomatic Answering Operation Monitoring incoming calls Listening to all recorded messages Flash Memory Message BackupListening to Messages Listening to only new messages Erasing all messages Erasing MessagesRecording a Memo Message Erasing a specific message Summary of remote operation Remote Operation from a Touch Tone Phone Display goes out Canceling the remote operationTo cancel, reprogram a new remote code Direct Remote Operation Direct commands Skipping the greeting message Remote Operation from a Touch Tone PhoneTo continue the remote operation Turning on the answering system Menu Remote Operation with the HandsetHelp menu During a conversation, press Then Recording your telephone conversation using the handsetContinue your conversation When finished, press then Remote Operation with the Handset Operating More than One Base Unit For Optional Multi-Unit UsersOperating More than One Handset Registering a Handset in the Base Unit RegistrationF7 i I000 Selecting the Base Unit AccessAutomatic base unit access Specified base unit access F70 i2 Registration Canceling a HandsetCanceling a base unit Iu2 Selecting the Stand-by Mode DisplayBell Selection F3 i0 Enter the handset number you want to ring Bell SelectionSelecting first handset Selecting all handsets Page, then press Intercom between the Handsets and the Base UnitPaging all the handsets from the base unit All paging Paging a handset from the base unit Individual paging Handset 1 Press I N T Enter the desired handset number Handset When the unit rings, press to answer00 00 0 Intercom Intercom between Handsets Transferring a call without the intercom Transferring a call using the intercomTransferring a Call from One Handset to Another Press Press G or F until F24 is displayed Press O K Setting the Call Waiting ToneF24 Intercom Conference Replacing the Batteries Selecting the battery typeBattery replacement After replacement Replacing the Batteries Before Requesting Help Cordless Telephone Problem Remedy Does not function Problem RemedyBefore Requesting Help Answering System Problem Remedy System from a touch tone phone Base unit, it suddenly stops Use indicatorYou cannot operate the answering System at the base unit General Problem Remedy Placement Safety InstructionsSafety Installations Environment Lightning surge KX-TCD961CXB57~68 99.12.3 222 PM Term Definitions PQQX12234ZA-UK WU1299NR0 Obchodní oddélení Panasonic Czech Republic, s.r.oKrakovská 9, 110 00, Praha 1, Èeská republika Výrobní závod