Location of Controls, Base unit | Panasonic KX-TCD961CXB instruction

KX-TCD961CXB(06~16) 99.12.3 2:04 PM Page 6

Location of Controls

Base unit

Display (p. 8)

Memo Button (p. 40)

ERASE Button (p. 17, 40)

GREETING Button (p. 17)

Charge Contacts (p. 12)

ANSWER ON Button and Indicator (p. 38)

Stop Button (p. 17, 39)

Volume Buttons , (p. 17)

Antenna

ANSAGE	TEXTE
	TEXTE	LÖSCHEN
		LÖSCHEN

ANSAGE

INTERN

Microphone (p. 17, 25, 40)		New Message Button
Microphone (p. 17, 25, 40)		(p. 39)
SELECT Button (p. 53)		Skip Button	(p. 39)
Charge Indicator (	) (p. 12)	Repeat Button	(p. 39)
In Use Indicator (	) (p. 48)	Locator/Intercom Button	(p. 25, 48, 53)

Page 6

Image 6

Panasonic KX-TCD961CXB Location of Controls, Base unit, New Message Button, Select Button p Skip Button Charge Indicator

Contents

Operating Instructions Charge the batteries for about 4 hours before initial use Serial No Date of purchase Battery p One Three Handset Cover p Belt Clip pBefore Initial Use Name and address of dealer Base Unit Location Battery ChargeFor Best Performance Obstructions such as walls Contents Selecting the Stand-by Mode Correct Use and Charging Base unit Select Button p Skip Button Charge IndicatorLocation of Controls New Message Button Handset 13, 18, 24, 27Tone Button Messages have been recorded DisplaysBase unit display Recording time is set to greeting only p Characters Display shows all possible configurationsIcons Is pressed while dialing Using the Belt Clip SettingsInstalling the Batteries in the Handset To remove the belt clip Connections Telephone Battery information Settings Battery ChargeBattery strength Recharge Press firmly Turning the Power onSelecting the Dialing Mode Press IUU Settings Selecting the Handset Ringer Volume/PatternRinger volume F23 Selecting the Base Unit Ringer Volume/Pattern 22u223U Preparing the Answering System Selecting the Voice Guidance LanguageTo select to Slovakian, press To select to Czech, press Greeting Message To set the greeting monitor Function itemTime p Function p Time and Day Adjustment To check the time/dayPress repeatedly to set the day Minutes Greeting onlyRecording time Current setting, 1 or 2, is displayed on the base unit Setting the Greeting Monitor FunctionPress Toll Saver When set to Auto Selecting the Number of Rings I2345678 To select the receiver volumeMaking Calls 00 00 To redial after confirming the numbers in redial memory Answering CallsTo redial the last number dialed To turn the handset ringer off temporarily Dialing a Stored Number Speed DialerStoring Phone Numbers in Memory To erase a stored number Intercom Paging the base unit from the handsetPaging the handset from the base unit Handset locator Setting the pause timing Special FeaturesHow to Use the Pause Feature To select 5 seconds, press To select 3 seconds, press Press For Rotary or Pulse Service Users Setting the Key LockUsing the Recall Feature To cancel the key lock Summary of Programmable Functions F5o - - o Setting the PasswordF5o 5o - - o Direct Call Setting the Direct Call ModeTo turn OFF the direct call mode F42 F4 Io To turn OFF the call prohibition modeCall Prohibition F4 IO0 Call Restriction To cancel the call restricted handsetsTo cancel the call restriction numbers I23456 F32U Selecting the Talk Mode DisplayPress G or F to select the desired setting During a conversation, the display will be as follows Automatic Route Selection Storing the Carrier Code/Area Codes To store the carrier codeTo store the area codes F25 Other Programmable SettingsF2 i F26 Clearing the Settings in Memory Function Monitoring incoming calls Setting the Unit to Answer CallsAutomatic Answering Operation Press Answer on to turn on the answering system Listening to only new messages Flash Memory Message BackupListening to Messages Listening to all recorded messages Erasing a specific message Erasing MessagesRecording a Memo Message Erasing all messages Remote Operation from a Touch Tone Phone Summary of remote operation Canceling the remote operation To cancel, reprogram a new remote codeDisplay goes out Direct commands Direct Remote Operation Turning on the answering system Remote Operation from a Touch Tone PhoneTo continue the remote operation Skipping the greeting message Remote Operation with the Handset Help menuMenu Remote Operation with the Handset Recording your telephone conversation using the handsetContinue your conversation When finished, press then During a conversation, press Then For Optional Multi-Unit Users Operating More than One HandsetOperating More than One Base Unit Registration F7 iRegistering a Handset in the Base Unit Specified base unit access Selecting the Base Unit AccessAutomatic base unit access I000 Registration Canceling a Handset Canceling a base unitF70 i2 F3 i0 Selecting the Stand-by Mode DisplayBell Selection Iu2 Selecting all handsets Bell SelectionSelecting first handset Enter the handset number you want to ring Paging a handset from the base unit Individual paging Intercom between the Handsets and the Base UnitPaging all the handsets from the base unit All paging Page, then press Intercom Intercom between Handsets Handset When the unit rings, press to answer00 00 0 Handset 1 Press I N T Enter the desired handset number Transferring a call using the intercom Transferring a Call from One Handset to AnotherTransferring a call without the intercom Intercom Conference Setting the Call Waiting ToneF24 Press Press G or F until F24 is displayed Press O K After replacement Selecting the battery typeBattery replacement Replacing the Batteries Replacing the Batteries Cordless Telephone Problem Remedy Before Requesting Help Problem Remedy Before Requesting HelpDoes not function Answering System Problem Remedy System at the base unit Base unit, it suddenly stops Use indicatorYou cannot operate the answering System from a touch tone phone General Problem Remedy Installations Environment Safety InstructionsSafety Placement Lightning surge KX-TCD961CXB57~68 99.12.3 222 PM Term Definitions Výrobní závod Obchodní oddélení Panasonic Czech Republic, s.r.oKrakovská 9, 110 00, Praha 1, Èeská republika PQQX12234ZA-UK WU1299NR0

Panasonic KX-TCD961CXB operating instructions Location of Controls, Base unit, New Message Button

Models: KX-TCD961CXB

Location of Controls

Base unit

New Message Button

SELECT Button (p. 53)

Skip Button

Charge Indicator (