Before Requesting Help, Problem Remedy | Panasonic KX-TCD961CXB

KX-TCD961CXB(57~68) 99.12.3 2:22 PM Page 60

Before Requesting Help

Problem

Remedy

You cannot program function items such as the dialing mode.

•Programming is not possible while the unit is in the talk or intercom mode.

•Do not pause for over 60 seconds while programming.

You cannot store a phone number in memory.

•You cannot store a phone number while the unit is in the talk or intercom mode.

•Do not pause for over 60 seconds while storing.

While programming function items or	• To answer the call, lift the handset or press		.
storing numbers, the unit starts to ring.	Start again from the beginning after hanging up.

does not function.	• The handset is too far from the base unit.
	• The handset is engaged in an outside call. Wait until
	the in use indicator (	) light goes out.

The paged handset does not answer.

•The handset is not in the same radio area.

•The handset is engaged in an outside call.

•The handset has been canceled or has not been registered. Register the handset in the base unit (p. 48).

While using the intercom, two tones sound.

•A call is being received. To answer, press twice.

60

Image 60

Panasonic KX-TCD961CXB operating instructions Before Requesting Help, Problem Remedy, Does not function

Contents

Operating Instructions Charge the batteries for about 4 hours before initial use Battery p One Three Handset Cover p Belt Clip p Before Initial UseSerial No Date of purchase Name and address of dealer Battery Charge For Best PerformanceBase Unit Location Obstructions such as walls Contents Selecting the Stand-by Mode Correct Use and Charging Select Button p Skip Button Charge Indicator Location of ControlsBase unit New Message Button Handset 13, 18, 24, 27Tone Button Displays Base unit displayMessages have been recorded Recording time is set to greeting only p Display shows all possible configurations IconsCharacters Is pressed while dialing Settings Installing the Batteries in the HandsetUsing the Belt Clip To remove the belt clip Connections Telephone Settings Battery Charge Battery strengthBattery information Recharge Turning the Power on Selecting the Dialing ModePress firmly Press Settings Selecting the Handset Ringer Volume/Pattern Ringer volumeIUU F23 Selecting the Base Unit Ringer Volume/Pattern 22u223U Preparing the Answering System Selecting the Voice Guidance LanguageTo select to Slovakian, press To select to Czech, press Greeting Message Function item Time pTo set the greeting monitor Function p Time and Day Adjustment To check the time/dayPress repeatedly to set the day Minutes Greeting onlyRecording time Setting the Greeting Monitor Function Press Toll Saver When set to AutoCurrent setting, 1 or 2, is displayed on the base unit Selecting the Number of Rings To select the receiver volume Making CallsI2345678 00 00 Answering Calls To redial the last number dialedTo redial after confirming the numbers in redial memory To turn the handset ringer off temporarily Speed Dialer Storing Phone Numbers in MemoryDialing a Stored Number To erase a stored number Intercom Paging the base unit from the handsetPaging the handset from the base unit Handset locator Special Features How to Use the Pause FeatureSetting the pause timing To select 5 seconds, press To select 3 seconds, press Press Setting the Key Lock Using the Recall FeatureFor Rotary or Pulse Service Users To cancel the key lock Summary of Programmable Functions Setting the Password F5oF5o - - o 5o - - o Setting the Direct Call Mode To turn OFF the direct call modeDirect Call F42 To turn OFF the call prohibition mode Call ProhibitionF4 Io F4 IO0 To cancel the call restricted handsets To cancel the call restriction numbersCall Restriction I23456 Selecting the Talk Mode Display Press G or F to select the desired settingF32U During a conversation, the display will be as follows Automatic Route Selection Storing the Carrier Code/Area Codes To store the carrier codeTo store the area codes Other Programmable Settings F2 iF25 F26 Clearing the Settings in Memory Function Setting the Unit to Answer Calls Automatic Answering OperationMonitoring incoming calls Press Answer on to turn on the answering system Flash Memory Message Backup Listening to MessagesListening to only new messages Listening to all recorded messages Erasing Messages Recording a Memo MessageErasing a specific message Erasing all messages Remote Operation from a Touch Tone Phone Summary of remote operation Canceling the remote operation To cancel, reprogram a new remote codeDisplay goes out Direct commands Direct Remote Operation Remote Operation from a Touch Tone Phone To continue the remote operationTurning on the answering system Skipping the greeting message Remote Operation with the Handset Help menuMenu Recording your telephone conversation using the handset Continue your conversation When finished, press thenRemote Operation with the Handset During a conversation, press Then For Optional Multi-Unit Users Operating More than One HandsetOperating More than One Base Unit Registration F7 iRegistering a Handset in the Base Unit Selecting the Base Unit Access Automatic base unit accessSpecified base unit access I000 Registration Canceling a Handset Canceling a base unitF70 i2 Selecting the Stand-by Mode Display Bell SelectionF3 i0 Iu2 Bell Selection Selecting first handsetSelecting all handsets Enter the handset number you want to ring Intercom between the Handsets and the Base Unit Paging all the handsets from the base unit All pagingPaging a handset from the base unit Individual paging Page, then press Handset When the unit rings, press to answer 00 00 0Intercom Intercom between Handsets Handset 1 Press I N T Enter the desired handset number Transferring a call using the intercom Transferring a Call from One Handset to AnotherTransferring a call without the intercom Setting the Call Waiting Tone F24Intercom Conference Press Press G or F until F24 is displayed Press O K Selecting the battery type Battery replacementAfter replacement Replacing the Batteries Replacing the Batteries Cordless Telephone Problem Remedy Before Requesting Help Problem Remedy Before Requesting HelpDoes not function Answering System Problem Remedy Base unit, it suddenly stops Use indicator You cannot operate the answeringSystem at the base unit System from a touch tone phone General Problem Remedy Safety Instructions SafetyInstallations Environment Placement Lightning surge KX-TCD961CXB57~68 99.12.3 222 PM Term Definitions Obchodní oddélení Panasonic Czech Republic, s.r.o Krakovská 9, 110 00, Praha 1, Èeská republikaVýrobní závod PQQX12234ZA-UK WU1299NR0