Panasonic PV-VM202 operating instructions Playing Back on Your TV, To Stop Audio Dubbing

[S-VIDEO IN]

[VIDEO IN] [AUDIO IN]

1

S-VIDEO

IN/OUT

Playing Back on Your TV

By connecting your Palmcorder with your TV, the recorded scenes can be viewed on your TV screen.

≥Before connecting them, turn off the power of both the Palmcorder and TV.

1Connect the [A/V IN/OUT] Jack of the Palmcorder to the

Video and Audio Input Jacks of the TV.

≥Using the A/V Cable 1 (supplied), make a connection with the TV. If

the TV has an S-Video Jack, connect the S-Video Cable (not supplied) 2, too.

Making the Indications Appear on the TV screen

Press the [OSD] Button 3 on the Remote Controller.

≥Be sure to select the proper input on your TV. (If necessary, consult your TV’s operating instructions.)

≥If you play back a Cassette recorded with copyright protection signals, the screen becomes blue or mosaic-like noise patterns appear.

≥If you set [AV JACK] on the [AV IN/OUT SETUP] Sub-Menu to [IN/OUT], nothing will be shown on the TV screen except during playback.

START/

DATE/ PHOTO STOP

OSD TIME SHOT

COUNTER RESET		TITLE ZOOM
MULTI/		T
		A.DUB
P-IN-P
	PLAY	FF/
		W
STILL ADV	PAUSE	STILL ADV
INDEX	STOP	INDEX
SELECT	VAR	PB

W.B./SHUTTER/IRIS/

2 MF/VOL/JOG 1 1, 2

PUSH

1

		DATE/	PHOTO	START/
	OSD			STOP
		TIME	SHOT
	COUNTER RESET		TITLE	ZOOM
	MULTI/			T
		¥REC	A.DUB
	P-IN-P			r
3				sVOL	4
	V/REW	PLAY	FF/W	W
	6	1	5
3, 5	STILL ADV	PAUSE	STILL ADV
	E	;	D
	INDEX	STOP	INDEX
	K	∫	L
	SELECT	VAR.		P.B.
		SEARCH		ZOOM

12

A.DUB; A.DUB!

~~~~~~~~~~~~~~~~~~~~~~~~~

Audio Dubbing

You can add music or narration to the recorded Cassette.

≥If you perform audio dubbing onto a tape that was recorded with [AUDIO-REC] on the [RECORDING SETUP] Sub-Menu of the [CAMERA FUNCTIONS] Main-Menu set to [16bit], the original sound is erased. (If you want to preserve the original sound, use the [12bit] Mode

when recording.)

≥Audio Dubbing cannot be performed onto recordings made in LP Mode. (l19)

1Set [VCR FUNCTIONS] >> [AV IN/OUT SETUP] >> [AV JACK] >>[IN/OUT].

2And then select [A.DUB INPUT] >> [MIC] or [AV IN].

≥Set to [AV IN] when an external device is used, or set to [MIC] when built-in microphone is used.

3Press the [1] Button, and then press the [;] Button at the point where you want to start dubbing.

4Press the [A.DUB] Button on the Remote Controller.

≥[A.DUB;] Indication appears. 1

5To start Audio Dubbing, press the [;] Button on the Remote

Controller.

≥[A.DUB!] Indication appears. 2

To Stop Audio Dubbing

Press the [;] Button on the Remote Controller.

The Palmcorder is in the Still Playback Mode again.

Playing Back the Sound Recorded with Audio Dubbing (For 12 bit Audio Recording)

Set [VCR FUNCTIONS] >> [PLAYBACK FUNCTIONS] >> [AUDIO] >> [ST2] or [MIX].

ST1: Play back only the original sound.

ST2: Play back only the sound added by Audio Dubbing

MIX: Play back both the original sound and the sound added by Audio Dubbing simultaneously.

≥For other notes, see page 62.

33