Pioneer SC-05, SC-07 manual Remote control, Hdmi, Additional information, Symptom, Remedy

Additional information 15

Symptom	Remedy
When playing a disc with the	• Make sure that the receiver is set to AUTO or DIGITAL (see Choosing the input signal on page 38).
listening mode set to Auto	• If a two channel soundtrack is currently playing (including Dolby Surround encoded), then this is
Surround, 2 PL II or Neo:6	not a malfunction. Check the disc packaging for details about the audio tracks available.
appear on the receiver.
During playback of a Surround	• The source may be Dolby Surround EX/DTS-ES software, but it has no flag to indicate it is 6.1
EX or DTS-ES source on the	compatible. Set to SBch ON (see Using surround back channel processing on page 39), then switch
SBch AUTO setting, EX or ES	to the THX Surround EX or Standard EX listening mode (see Listening in surround sound on page 35).
does not appear, or the signal
is not properly processed.
During playback of DVD-Audio,	• This will occur when playing DVD-Audio material over the HDMI connection. This is not a
the display shows PCM.	malfunction.

Remote control

Symptom	Remedy
Cannot be remote controlled.	• Try replacing the batteries in the remote control (see Loading the batteries on page 8).
	• Be sure to operate within 7 m (23 feet) and a 30º angle of the remote sensor on the front panel (see
	Operating range of remote control unit on page 31).
	• Check that there are no obstacles between the receiver and the remote control.
	• Make sure that there is no fluorescent or other strong light shining on to the remote sensor.
	• Check the connections of the CONTROL IN jack (see Operating other Pioneer components with this
	unit’s sensor on page 108).
Other components can’t be	• If the battery ran down, the preset codes may have been cleared. Re-enter the preset codes.
operated with the system	• The preset code may be incorrect. Redo the procedure for entering preset codes.
remote.
The SR cable is connected, but	• Reinsert the SR cable, making sure it’s connected to the right jack (see Using this receiver with a
the connected components	Pioneer flat panel TV on page 70).
can’t be operated with the	• Make sure that there is an analog or HDMI connection between the units. This is necessary for the
remote.	SR feature to work.
	• Check that the other component is made by Pioneer. The SR feature only works with Pioneer
	equipment.

HDMI

Symptom	Remedy
The HDMI indicator blinks	• Check all the points below.
continuously.
No picture or sound.	• This receiver is HDCP-compatible. Check that the components you are connecting are also HDCP-
	compatible. If they are not, please connect them using the component, S-Video or composite video
	jacks.
	• Depending on the connected source component, it’s possible that it will not work with this receiver
	(even if it is HDCP-compatible). In this case, connect using the component, S-Video or composite
	video jacks between source and receiver.
	• If the problem still persists when connecting your HDMI component directly to your monitor,
	please consult the component or monitor manual or contact the manufacturer for support.
	• If video images do not appear on your TV or flat panel TV, try adjusting the resolution, DeepColor
	or other setting for your component.
	• If ‘NOT SUPPORT’ appears in the receiver’s display, try adjusting the resolution, DeepColor or
	other setting for your component.
	• While analog video signals are being output over HDMI, use a separate connection for audio
	output.
	• When this receiver reproduces MULTI CH IN audio sources with the HDMI setting set to
	THROUGH, you cannot hear audio output from all channels. In this case, make a digital or analog
	audio connection.
	• To output signals in DeepColor, use an HDMI cable (High Speed HDMI™ Cable) to connect this
	receiver to a component or TV with the DeepColor feature.

117

En