Pioneer SC-07, SC-05 Switching components on and off using the 12 volt trigger, Other connections

09Other connections

Switching components on and off using the 12 volt trigger

You can connect components in your system (such as a screen or projector) to this receiver so that they switch on or off using 12 volt triggers when you select an input function. However, you must specify which input functions switch on the trigger using the The Input Setup menu on page 92. Note that this will only work with

components that have a standby mode.1

12V

TRIGGER

Using this receiver with a Pioneer flat panel TV

If you have a Pioneer flat panel TV, you can use an SR+

cable2 to connect it to this unit and take advantage of various convenient features, such as automatic video input switching of the flat panel TV when the input is

changed.3

CONTROL

OUT

Pioneer flat panel TV

LAN(10/100)		12 V	1	IN 1			IN
	XM	TRIGGER
	IN	(OUTPUT	(DVD)			(VIDEO1)	LAN(10/100)
	COAXIAL	12V
								XM
		TOTAL
	ASSIGNABLE							IN
		50mA
	IN 1 (DVD)		2 PR	PB	Y	PR	P	COAXIAL
HDMI		MAX)
				ZONE 2 OUT				ASSIGNABLE
		SIRIUS		R		L		IN 1 (DVD)
BD							HDMI
	IN 2 (CD)					ZONE 2
IN		IN					BD
						OUT	IN	IN 2 (CD)
	IN 3 (DVR2)	IR				ZONE 3		IN 3 (DVR2)
						OUT	IN
							1	IN 1
• Connect the 12 V TRIGGER jack of this receiver to
								(TV/SAT)
the 12 V trigger of another component.							2	IN 2
							IN	(DVR1)

Use a cable with a mono mini-plug on each end for the		(VIDEO1)
		IN 3
connection.	IN	(CD-R)
	3	IN 4
• The trigger maximum power is DC OUT 12 V/50 mA.	ASSIGNABLE 1 - 3	ASSIGNABLE
	OUT	SOURCE
		ZONE3/
	1	OUT
After you’ve specified the input functions that will switch	(HDMI
	CTRL)
		SOURCE
on the trigger, you’ll be able to switch the component on	OUT	OUT
		OPTICAL
	2

DIGITAL

or off just by pressing the input function(s) you’ve set on page 92.

Important

12 V	1		IN 1
TRIGGER
(OUTPUT		(DVD)			(VI
12V
TOTAL
50mA		PR	PB	Y	PR
MAX)	2		ZONE 2 OUT
SIRIUS			R		L
IN					Z
IR					Z
IN			PHONO		CD
1			IN		IN
IN		SIGNAL
		GND	L
2
OUT
			R
IN
CONTROL
OUT
				CAUTION:
				SPEAKER IMPED
				ATTENTIO
				ENCEINTE D'IMP
					SELECTAB
					SEE INSTR
					MANUAL
					SELECTAB
RS-232C					VOIR LE M
					D'EMPLOI

• You can’t use the SR+ features when HDMI Control is set to ON. Make sure to set HDMI Control to OFF when you use the SR+ features (page 90).

• If you connect to a Pioneer flat panel TV using an SR+ cable, you will need to point the remote control at the flat panel TV remote sensor to control the receiver. In this case, you won’t be able to control the receiver using the remote control if you switch the flat panel TV off.

• Before you can use the extra SR+ features, you need to make a few settings in the receiver. See The Input Setup menu on page 92 and SR+ Setup for Pioneer flat panel TVs on page 95 for detailed instructions.

Note

1 Triggered connections with up to two devices compatible with 12-volt triggers can be made with this receiver.

2 The 3-ringed SR+ cable from Pioneer is commercially available under the part number ADE7095. Contact the Pioneer Customer Support division for more information on obtaining an SR+ cable (you can also use a commercially available 3-ringed mini phone plug for the connection).

3 This receiver is compatible with all SR+ equipped Pioneer flat panel TVs from 2003 onward.

70

En