Beyond the Basics Resetting your scanner | Radio Shack 20-426

Beyond the Basics

resetting your scanner

If the scanner’s display locks up or stops operating properly, you might need to reset the scanner.

	Note	This procedure clears all the information you have stored
	Note	in the scanner. Before you reset the scanner, try turning
		in the scanner. Before you reset the scanner, try turning
		it off and on to see if it begins working properly. Reset
		the scanner only when you are sure it is not working
		properly.

1.Make sure your scanner is turned off.

2.While holding down 2, 9, and HOLD, turn on the scanner. After about 2 seconds the scanner initializes and CLEAr appears.

Follow these steps to restore the 150 preprogrammed frequencies stored in the private bank.

1.Make sure your scanner is turned off.

2.While holding down 3 and E, turn on the scanner. After several seconds, the scanner restores the frequencies.

78

Image 78

Radio Shack 20-426 manual Beyond the Basics Resetting your scanner, Properly

Contents

Pro-2051 1,000-Channel Triple Trunking Mobile/Base Scanner Contents Basics Power your scannerSet up your scanner Basics Scanning a private bank Advanced scanner featuresBeyond the Basics Highway patrol alerts Wired programming Contents SkywarnSignal Stalker Warranty Your scanner’s keypad HOLD/RESUME To Do This Your scanner’s rear view Your scanner’s display Trunk FCC wants you to know Install your scanner Mounting the scanner in your vehicle Power your scanner From a wall outletThrough your vehicle’s ignition negative ground only From your vehicle’s cigarrette lighter Rear View Connecting the supplied antenna Connecting an external antennaConnect your scanner Connecting an external speaker Use extreme caution when installing or removing an Listening Safely Set up your scanner Turn on your scannerSet the squelch Basics Listen to preprogrammed frequencies Common scanner termsScanning overview Basics Channel storage banks Advanced scanner featuresBeyond the Basics Storing known frequencies into channels Beyond the Basics Beyond the Basics Deleting a stored frequency Locking out a channel in hold modeLocking out a channel in scanning mode Locking out channels Restoring a locked-out channel in hold mode Memory lockRestoring all locked-out channels Direct channel access Beyond the Basics Hold/resume Scanning a private bank Beyond the Basics Priority scan Changing the priority channel Service scanning Setting a search band Beyond the Basics Band search Data skip Search hold Beyond the Basics Frequency skip Storing search frequencies Delay Highway patrol alerts Highway patrol/local police scanningSelecting the state State Code Order Press these buttons Action Setting the alert tone volume Beyond the Basics Scan holdHighway warning alert Muting the alert tone Adjusting alertHighway patrol priority channels Skip frequencies Trunked highway frequencies Skywarn About Skywarn NWR Same Programming a Fips code Programming Fips Beyond the Basics Signal Stalker Setting the signal stalker options Beyond the Basics Using signal stalker Setting the squelch Trunk tracking Programming trunking frequencies Selecting Trunking System Type Programming id scan lists manually Motorola talk groups Edacs talk groups LTR talk groups Receiving trunked systems ID scan mode ID scan hold mode Direct entry id hold mode ID search modeID search hold mode ID monitor mode Programming scan lists during searchDeleting a stored ID ID lockout Reviewing ID lockoutRestoring locked-out IDs Setting the delay mode for trunking mode Setting priority in trunking modeTrunking frequency conﬁrmation Moving between scan list memories Multi-track About multi-track Edacs tracking Programming Edacs system frequencies Special Edacs features Beyond the Basics An Edacs trunked systemAFS partial entry Edacs ID range search Edacs ID blockout Tracking LTR systems Edacs Scat Beyond the Basics Tracking Motorola systems ﬂeet map programming Preset Fleet Maps E1P1 E1P5 E1P11 Selecting a Preset Fleet Map User-deﬁned ﬂeet maps Fleet Map Size Codes Size code restrictions Programming a user ﬂeet mapProgramming a Hybrid system You can only enter within a range of 5-100 kHz, and 5 or Toggling the status bit Control channel only mode Disconnect tone detect option end code If the scanner receives no data from the PC for more than Cloning your scanner Replacing the fuse in the DC power cord Birdies Beyond the Basics Resetting your scanner Properly Frequently asked questions FAQs Drive by patrol cars but do not hear alarms? Error appears on the display. What does it mean? Speciﬁcations If Frequencies Glossary Service and repair Care