Direct entry id hold mode, ID search mode | Radio Shack 20-426

Beyond the Basics

direct entry id hold mode

Enter the ID you want to receive by using 1 through 9, 0 (or ./ CLR) and press d, and you can listen to a speciﬁc ID (without storing ID to the list).

ID search mode

Once you have programmed all the frequencies for a trunked system, search will let you immediately start hearing transmissions. When in the trunking mode, press SRCH and the scanner begins to ﬁnd any active IDs. When the scanner ﬁnds the control channel data, the scanner begins trunking, and -- --- appears on the display until the scanner ﬁnds an ID. If the scanner does not ﬁnd an ID in about 1 second, it moves on to conventional channels in the same bank or to the next active bank. This may happen a few times (if the signal is weak) when the scanner comes around to that bank again. The scanner will recognize the control channel was lost when no ID can be found, even if the scanner tries ten times.

The scanner will begin to search for the control data channel. If it ﬁnds any non-locked-out IDs, you will hear it. You will then hear any replies that follow within the speciﬁed periods.

After that, the scanner will move on and not continuously search the system for additional IDs (on busy systems you would never leave the system if this were the case). If you press e while monitoring an ID, the radio will check if any other IDs are active (it will disregard the ID you just left), and none are active, the scanner resumes searching.

ID search hold mode

If you hear an interesting ID during search mode and want to continue listening to it, press HOLD/RESUME. HOLD and the ID appear.

53

Image 53

Radio Shack 20-426 manual Direct entry id hold mode, ID search mode, ID search hold mode

Contents

Pro-2051 1,000-Channel Triple Trunking Mobile/Base Scanner Contents Set up your scanner Power your scannerBasics Basics Beyond the Basics Advanced scanner featuresScanning a private bank Highway patrol alerts Signal Stalker Contents SkywarnWired programming Warranty HOLD/RESUME Your scanner’s keypad To Do This Your scanner’s rear view Trunk Your scanner’s display FCC wants you to know Mounting the scanner in your vehicle Install your scanner Through your vehicle’s ignition negative ground only Power your scannerFrom a wall outlet Rear View From your vehicle’s cigarrette lighter Connect your scanner Connecting the supplied antennaConnecting an external antenna Use extreme caution when installing or removing an Connecting an external speaker Listening Safely Set the squelch Set up your scannerTurn on your scanner Scanning overview Basics Listen to preprogrammed frequenciesCommon scanner terms Basics Beyond the Basics Advanced scanner featuresChannel storage banks Storing known frequencies into channels Beyond the Basics Locking out a channel in scanning mode Locking out a channel in hold modeBeyond the Basics Deleting a stored frequency Locking out channels Restoring all locked-out channels Restoring a locked-out channel in hold modeMemory lock Beyond the Basics Hold/resume Direct channel access Scanning a private bank Changing the priority channel Beyond the Basics Priority scan Service scanning Beyond the Basics Band search Setting a search band Search hold Data skip Storing search frequencies Beyond the Basics Frequency skip Delay Selecting the state Highway patrol alertsHighway patrol/local police scanning State Code Order Press these buttons Action Highway warning alert Setting the alert tone volumeBeyond the Basics Scan hold Highway patrol priority channels Adjusting alertMuting the alert tone Skip frequencies Trunked highway frequencies About Skywarn Skywarn NWR Same Programming Fips Programming a Fips code Beyond the Basics Signal Stalker Setting the signal stalker options Beyond the Basics Using signal stalker Trunk tracking Setting the squelch Programming trunking frequencies Selecting Trunking System Type Programming id scan lists manually Edacs talk groups Motorola talk groups Receiving trunked systems LTR talk groups ID scan hold mode ID scan mode ID search hold mode Direct entry id hold modeID search mode Deleting a stored ID ID monitor modeProgramming scan lists during search Restoring locked-out IDs ID lockoutReviewing ID lockout Trunking frequency conﬁrmation Setting the delay mode for trunking modeSetting priority in trunking mode Multi-track Moving between scan list memories About multi-track Programming Edacs system frequencies Edacs tracking AFS partial entry Special Edacs featuresBeyond the Basics An Edacs trunked system Edacs ID blockout Edacs ID range search Edacs Scat Tracking LTR systems Beyond the Basics Tracking Motorola systems ﬂeet map programming Preset Fleet Maps E1P1 E1P5 E1P11 User-deﬁned ﬂeet maps Selecting a Preset Fleet Map Fleet Map Size Codes Programming a Hybrid system Size code restrictionsProgramming a user ﬂeet map You can only enter within a range of 5-100 kHz, and 5 or Toggling the status bit Control channel only mode Disconnect tone detect option end code If the scanner receives no data from the PC for more than Cloning your scanner Birdies Replacing the fuse in the DC power cord Properly Beyond the Basics Resetting your scanner Drive by patrol cars but do not hear alarms? Frequently asked questions FAQs Error appears on the display. What does it mean? If Frequencies Speciﬁcations Glossary Care Service and repair