Selecting Trunking System Type | Radio Shack 20-426 specs

Beyond the Basics

STEP 1: Selecting Trunking System Type

The ﬁrst step in a trunk tracking system is storing the frequencies in one of the ten available banks in your scanner.

1.Press TRUNK in conventional programming mode. BANK and TRUNK will begin to ﬂash on the display.

2.Select the bank in which you want to store the frequency by using the keypad.

3.Select the system you want to track by pressing e or d, then press E.

List of trunking systems are as follows:

E2-800 (Motorola Type II 800 MHz)

E2-Hi (Motorola Type II VHF 136-174 MHz) *

E2-UHF (Motorola Type II UHF 406-512 MHz) *

E1 (Motorola Type I and Hybrid) **

Ed (EDACS Wide Band: 9600 band)***

Ed-SCt (EDACS Scat)

Lt (LTR)

*Requires programming of a base and spacing frequency offset channel (See “Setting the Base, Spacing Frequencies and Offset Channel for Motorola VHF/UHF Trunked Systems”).

**Requires programming of a ﬂeet map (See “Programming a User Fleet Map”).

***Requires programming of frequencies in exact order and location.

STEP 2: Programming Trunking Frequencies 1. Select Prog F and press E.

2. Use the keypad and ./CLR to enter a frequency for the trunked system. For example, enter 851.0125.

Note

To clear a mistake while entering a frequency, press ./CLR twice, and start over.

48

Image 48

Radio Shack 20-426 manual Selecting Trunking System Type

Contents

Pro-2051 1,000-Channel Triple Trunking Mobile/Base Scanner Contents Power your scanner Set up your scannerBasics Basics Advanced scanner features Beyond the BasicsScanning a private bank Highway patrol alerts Contents Skywarn Signal StalkerWired programming Warranty Your scanner’s keypad HOLD/RESUME To Do This Your scanner’s rear view Your scanner’s display Trunk FCC wants you to know Install your scanner Mounting the scanner in your vehicle Power your scanner From a wall outletThrough your vehicle’s ignition negative ground only From your vehicle’s cigarrette lighter Rear View Connecting the supplied antenna Connecting an external antennaConnect your scanner Connecting an external speaker Use extreme caution when installing or removing an Listening Safely Set up your scanner Turn on your scannerSet the squelch Basics Listen to preprogrammed frequencies Common scanner termsScanning overview Basics Advanced scanner features Beyond the BasicsChannel storage banks Storing known frequencies into channels Beyond the Basics Locking out a channel in hold mode Locking out a channel in scanning modeBeyond the Basics Deleting a stored frequency Locking out channels Restoring a locked-out channel in hold mode Memory lockRestoring all locked-out channels Direct channel access Beyond the Basics Hold/resume Scanning a private bank Beyond the Basics Priority scan Changing the priority channel Service scanning Setting a search band Beyond the Basics Band search Data skip Search hold Beyond the Basics Frequency skip Storing search frequencies Delay Highway patrol alerts Highway patrol/local police scanningSelecting the state State Code Order Press these buttons Action Setting the alert tone volume Beyond the Basics Scan holdHighway warning alert Adjusting alert Highway patrol priority channelsMuting the alert tone Skip frequencies Trunked highway frequencies Skywarn About Skywarn NWR Same Programming a Fips code Programming Fips Beyond the Basics Signal Stalker Setting the signal stalker options Beyond the Basics Using signal stalker Setting the squelch Trunk tracking Programming trunking frequencies Selecting Trunking System Type Programming id scan lists manually Motorola talk groups Edacs talk groups LTR talk groups Receiving trunked systems ID scan mode ID scan hold mode Direct entry id hold mode ID search modeID search hold mode ID monitor mode Programming scan lists during searchDeleting a stored ID ID lockout Reviewing ID lockoutRestoring locked-out IDs Setting the delay mode for trunking mode Setting priority in trunking modeTrunking frequency conﬁrmation Moving between scan list memories Multi-track About multi-track Edacs tracking Programming Edacs system frequencies Special Edacs features Beyond the Basics An Edacs trunked systemAFS partial entry Edacs ID range search Edacs ID blockout Tracking LTR systems Edacs Scat Beyond the Basics Tracking Motorola systems ﬂeet map programming Preset Fleet Maps E1P1 E1P5 E1P11 Selecting a Preset Fleet Map User-deﬁned ﬂeet maps Fleet Map Size Codes Size code restrictions Programming a user ﬂeet mapProgramming a Hybrid system You can only enter within a range of 5-100 kHz, and 5 or Toggling the status bit Control channel only mode Disconnect tone detect option end code If the scanner receives no data from the PC for more than Cloning your scanner Replacing the fuse in the DC power cord Birdies Beyond the Basics Resetting your scanner Properly Frequently asked questions FAQs Drive by patrol cars but do not hear alarms? Error appears on the display. What does it mean? Speciﬁcations If Frequencies Glossary Service and repair Care