139, Command Function | Sanyo 1AV4U19B25500 guide

Use of telnet

4.Type the commands, refer to below table, to control the projector and then press "Enter" key for termination. For example, type "C00" which is a command to turn on the projector, and press "Enter" key. Confirm the projector is turning on.

*Enter with ASCII 64-byte capital characters and one-byte characters.

To disconnect the communication, press "Ctrl" key and "]" key at the same time, type "close" and then press "Enter" key on the Keyboard.

> close [return]

The table below shows the typical command lists for controlling this projector and please consult your local dealer for further information of another commands.

Command list table

Command		Function

	C00	Power on
	C02	Power off
	C09	Volume up
	C0A	Volume down
	C0B	Audio Mute on
	C0C	Audio Mute off
	C1C	Menu display on
	C1D	menu display off

*1 Further instructions about the telnet application, please see the on-line guide on your computer.

*2 The password is a Network PIN code decided item "Network PIN code setting" (☞p.32, 42). If the authentication of the entered password is failed 4 times continuously, the communication will be disconnected automatically. Please try again for the connection.

*3 If the password or any command is not entered for more than 30 seconds, the communication will be disconnected automatically. Please try again for the connection.

139

Image 139

Sanyo 1AV4U19B25500 owner manual 139, Command Function

Contents

Network Set-up and Operation For Windows FCC RF Exposure Warning Federal Communications Commission NoticeFor Canadian Users FCC Warning Διαταξεισ ΤΗΣ Οδηγιασ 1999/5/ΕΚ Expression/Abbreviation Trademarks and CopyrightUse of this manual Table of contents Controlling the projector Basic setting and operationNetwork capture functions 133 113137 Required operating environment for computers Compliance Network specifications of the projectorWireless LAN LAN Terminal You cannot setup or control the projector via the network How to project the computer screen’s image via the networkHow to use all functions concerning the network Check Did you make a network setting in the projector? Yes About LAN functions Chapter Image projecting system via LAN LAN functions and the featuresFlow of Image Transfer An example of the connection LAN connection modes Operate the computer mouse with the remote control About LAN functions Setup procedures Select Wired LAN or Wireless LAN then connect Install the software on computersLAN and set the configuration Network Configuration has completed Network Viewer & Capture 5 installation Installing the software Setup procedures Network Viewer 5 File Converter Installed softwareFollowing 3 softwares are installed on your computer Network Capture Installed software and places File Converter 2 installation Names and functions of the operation screen Network connection standby display Specify IP button Wireless easy setting button / Wireless easy release buttonNetwork Capture 5 window Search PJ button Start communication button 3Parameter setup button4Volume adjust slider and Mute check box Using the multiple network adaptors Wired LAN configurations Network environment settings Connecting to the LAN line Description Confirming the operation Confirming the operation Network information Network PIN code Wired factory default Selected LAN Wired LAN factory default settings Wireless LAN configurations Setting procedures Setting the network environment Environment *1 Identifier of the wireless access pointWPA2-PSK are not available Configuring security with the projector Use of security type WEP Available PSK key characters Use the Point ed buttons to select WPA-PSK security typeDigits Setting Procedures Easy wireless setting Computer environment and Wireless LAN connection Wireless factory default Wireless indicator display Selected LAN Wireless LAN factory default settings Basic setting and operation Starting up the Browser Select a display mode and login Main menu Display of main settingMain setting page in the Standard Mode display Setting Setting Pallet How to use the settingMain setting page in the Light Mode display Example of the Setting Radio button setting Type of the setting palletText box setting Pull-down menu setting Japanese Initial settingSwitches PJLink password authentication on or off Password for PJLink function PJLink and password setting Network PIN code settingWhats PJLink? Auto setting Date and time settingManual setting Sets Dhcp or Manual Network configurationSetting of LAN Selects LAN1 to LAN5 and Simple Then on the projector Configuring wireless LAN setting Configuring wireless LAN setting and security setting ItemDescription Configuring wireless LAN security setting Setting Smtp server and administrator address Mail setting Option selection for sending alert mail Registering and deleting E-mail addressesHours. Attached message Examples Type and contents of alert mail When lamp corres. value reaches preselect use time When PJ lamp replacement time is reached Community Snmp settingEnter user name of the projector etc. optional Enter place of the projector optional Public TrapTrap check/delete Check and delete the trap address Trap option Trap option setting Basic setting and operation Controlling the projector PJ status Power control and status checkPJ temp Status Description About projector condition Input Controls System System of the input signal575p, 720p, 1035i Image mode Video Computer Image adjustment Sound Adjusts the sound volume from the speakersSuppresses the sound PC adjustment Screen mode Video Computer Setting up the projectorNormal True Full Zoom Wide Natural wide Custom Sets the input signal form of Hdmi input Sets Auto PC Adjustment modeSets the auto-input signal detection mode Sets Auto Keystone mode On1 Highland mode Remote controlSets the color of the contents. Color/White Off Normal mode How to set the timer Timer settingSet a day or date Select an event action Check the timer eventsChange the event mode Set an execute time Event Projector PowerTime Items Description Projector information Indication of the lamp status Multi-control Controlling and setting the multi-projectorsExample of multi control Stops multi control function Start/stop the multi controlMenu are linked to the main menu Confirmation of registered projector Register the projector Mode Operation Change the mode of the registered projectorStatus Controlling all together Check & Change page in the light modeSetting all together Check & Change page in the light mode Viewer auto setting all together Network capture functions Network Communication +p.96 About Network Capture functionStart up the Network Capture Real Time Capture +p.91 Menu during Network Communication Commands on the task barMenu during Real time capturing Menu during Playing movie files Parameter set up Registering the computers Using the Real Time Capture Control by the computer Control by the web browser Set enable or disable the real time capturingReal time capturing operation Control by the projector For the following operations, refer to Control by the computer with USB memory Start the presentation Using the Network CommunicationSetting condition Example of advanced use Perform capture setting following to the description below Settings before using the Network Communication Description of capture editing window Menu tree Tool bar button names How to use the Network communication Drawing figures Setting of the drawing tool attribute101 Edit capture image Set type face, style, size and effects of the font Letter attribute setting102 Drawing letter On the Communication Network Communication operation and change of state103 Preparation 104 Executing the forcing mode Clients Moderator function105 Projector Moderator 106 Preparation for using the moderator functionNormal mode application window Moderator mode application window Moderator operation Using the moderator function107 Description of application window Unregister moderator status Moderators password setting up108 Error messages Cause and corresponding Error information109 110 Playing the movie files Forward 111 112 113 Network Viewer functions 114 How to use the Network Viewer 5 File ConverterMenu Command Tool Button Creating the available data Network Viewer Menu Sub Menu Description View Command Tool ButtonCreating the available data 115 Network Viewer functions 117 Setting of output destination and conversion modeConversion mode Output destination Select a folder and click Save button Creating a program file Program Editor Procedure of making program119 Moves up the selected folder path 120Displays the folder selection window Deletes the folder path from the folder list 121 Setting up the display order and time of the imagesSub menu Description Red frame Shows that image is deleted from the folder Image frame on the index window122 Blue frame 123 Example of the created program selectionLimitation of the Program file Condition to use the Network Viewer function Using the Network Viewer functionSelect Network for input mode previously 124 Setup the setting page 2 of the Selection Display Setup the setting page 1 of the Visual display125 126 127 Auto Display setting and controlMeans endless play Description Error informationError type 128 Display time of image 3 to 240 sec 129Display length Repeat times Sets display periods and repeating times 130 Use of the projector as FTP server 131 132 133 Network Projector Windows Vista 134 Use of Connect to a Network Projector Example ¥¥server¥projector¥pj01 135Click Connect button to connect to the projector 136 137 Appendix 138 Use of telnetControl 139 Command Function Proxy setting Web browser settingActive Script/JavaScript enable Flash Player enable Examples OS/Browsers ActiveX controls and plug-ins settingWindows XP Professional 141 142 Flash Player Add-on settingUsing proxy server Not using proxy server 143 Flash Player Plug-in settingNetscape Navigator 144 On recommended Checked Dont allow exceptions Unchecked Firewall settingClick OK to close setting 145 146 Troubleshooting 147 Infrastructure ModeCannot start up the browser Cannot be turned on/off with the web browser 148Speed of playing back images are very slow Images from the file server don’t appear on the screen? 149Cannot make a new program file 150 Microsoft power point format .pptWhat kind of image formats can I convert? CD-ROM AutoCapture 151Auto Capture does not start automatically 152 Terminology IEEE802.11n 153IEEE802.11b IEEE802.11g SO-WIN-KY7AC