Manuals / Sanyo / Household Appliance / Air Conditioner

Sanyo 85464359981002 Selecting The Installation Site, Indoor Unit AVOID, Ceiling-MountedType, Fig

Models: 85464359981002

1 90

Download 90 pages 27.37 Kb

Page 17

2. SELECTING THE INSTALLATION SITE

2. SELECTING THE INSTALLATION SITE

2-1. Indoor Unit

AVOID:

●areas where leakage of flammable gas may be expected.

●places where large amounts of oil mist exist.

●direct sunlight.

●locations near heat sources which may affect the performance of the unit.

●locations where external air may enter the room directly. This may cause “sweating” on the air dis- charge ports, causing them to spray or drip.

●locations where the remote controller will be splashed with water or affected by dampness or humidity.

●installing the remote controller behind curtains or furniture.

●locations where high-frequency emissions are generated.

DO:

●select an appropriate position from which every corner of the room can be uniformly cooled.

●select a location where the ceiling is strong enough to support the weight of the unit.

●select a location where tubing and drain pipe have the shortest run to the outdoor unit.

●allow room for operation and maintenance as well as unrestricted air flow around the unit.

●install the unit within the maximum elevation difference above or below the outdoor unit and within a total tubing length (L) from the outdoor unit as detailed in Table 1-16.

●allow room for mounting the remote controller about 3 ft. off the floor, in an area that is not in direct sunlight nor in the flow of cool air from the indoor unit.

NOTE

Air delivery will be degraded if the distance from the floor to the ceiling is greater than 10 ft.

Ceiling-Mounted Type

Ceiling

	Wall
min. 10 in.	min. 10 in.

Front view

NOTE

The rear of the indoor unit can be installed flush against the wall.

Air

discharge

min. 2 ft.	Air intake

Side view	Max. 10 in.
	Obstacle

Fig. 2-1

Concealed Duct (High-Static Pressure) Type 4-Way Air Discharge Semi-Concealed Type

3 ft.

3ft.

3 ft.

3 ft.	3 ft.

Fig. 2-2

1-Way Air Discharge Semi-Concealed Type

Ceiling

	ft.		Air
	3		discharge	Air
	n.	min. 2 in.	discharge	Air	Wall
	n.	min. 2 in.		intake	Wall
	mi		Wall	intake

	min. 2 in.
Obstacle	Side view
	Side view

Fig. 2-3

Wall-Mounted Type

min.	min. 6 in. min.
6 in.	6 in.

Front View

Fig. 2-4

17

Image 17

Sanyo 85464359981002 Selecting The Installation Site, Indoor Unit AVOID, Ceiling-MountedType, Fig, Wall-MountedType

Contents

R410A Models Indoor Units X A U D T KOutdoor Units Optional ControllersELECTRICIAN SHOULD ATTEMPT TO WIRE THIS SYSTEM SPECIAL PRECAUTIONS…In a Room …In Moist or Uneven LocationsCheck of Density Limit Manifold gauge Vacuum pump 1. Care regarding tubing3. Different tools required Single-outletvalve 1. Compressor specifications are different2. Existing tubing cannot be used especially R22 R410A3.HOW TO INSTALL THE INDOOR UNIT . . . . . CONTENTS4-WayAir Discharge Semi-ConcealedType X Type 1-WayAir Discharge Semi-ConcealedType A Type6. HOW TO PROCESS TUBING . . . . . . . . . . . . 1-2.Accessories Supplied 1-1.Tools Required for Installation not suppliedobtaining wire. Also, check 1. GENERALTable 1-3 1-WayAir Discharge Semi-Concealed Table 1-2 4-WayAir Discharge Semi-ConcealedTable 1-4Concealed Duct Part NameTable 1-6 Ceiling-Mounted Table 1-5Concealed Duct High-StaticPressureTable 1-7 Wall-Mounted 1-5.Tubing Size Table 1-8Main Tubing Size LA1-6.Straight Equivalent Length of Joints Table 1-12Required Copper Tubing DimensionsTable 1-11Straight Equivalent Length of Joints 1-7.Additional Refrigerant Charge1, 2... n 1-9.Tubing Length1+ 2 +... n-1 Allowable elevation1-11.Installing Distribution Joint unit is installed 1-10.Check of Limit DensityPay special attention to any location, such as a basementTable 1-12.Optional Distribution Joint KitAdditional refrigerant charging Main tubing ExampleDistribution joint tubing Checking of limit density2-1.Indoor Unit AVOID 2. SELECTING THE INSTALLATION SITECeiling-MountedType Fig.In case of multiple installations Installation space2-2.Outdoor Unit AVOID Fig.2-3.Air Discharge Chamber for Top Discharge 2-4.Installing the Unit in Heavy Snow AreasCountermeasures against snow and wind Fig.CHX03652/06052 2-6.Dimensions of Air-DischargeChamberCHX03652/06052 Unit: inRequired space around outdoor unit CHX03652/06052 Reference for air-dischargechamber field supplyUnit: in 2-8.Dimensions of Snow DuctingUnit: in Space requirements for setting – CHX03652/06052 Reference diagram for snow-proofducting –Obstacle to the rear of unit Obstacle to the front of unitObstacles to the front and rear of unit Installation in front-rearrowsReference diagram for snow-proofducting – Space requirements for setting – CHX03652/060523-2.Suspending the Indoor Unit 3. HOW TO INSTALL THE INDOOR UNITTable Fig.Tighten the hose clamps so 3-4.Installing the Drain Pipingtheir locking nuts face upward Fig.3-5.Checking the Drainage start when you short the pinBe careful since the fan will on the indoor control boardRemoving the corner cover 3-6.How to Install the Ceiling PanelFig. Fig.Fig. 3-6-2.Installing the Ceiling PanelFig. Fig.3-6-4.How to Attach the Corner & Air-IntakeGrille 3-6-3.Wiring the Ceiling PanelAttaching the corner cover and air-intakegrille Fig.3-6-7.Adjusting the Auto Flap 3-6-5.Checking After Installation3-7.Special Remarks DC Fan Tap Change Procedure Fig.1-WayAir Discharge Semi-ConcealedType A Type 3-8.Suspending the Indoor UnitFig. Fig.Fig. 3-9.Placing the Unit Inside the CeilingFig. Fig.Fig. 3-10.Installing the Drain PipingFig. Fig.3-11.Checking the Drainage Do not use natural drainageFig. Fig.1 Wiring connections 3-12.Electrical Power Wiring2 Wiring 3-13.How to Install the Ceiling PanelRemoving the intake grille Fig. 3-13-2.Installing the ceiling panelRemoving the side panel Fig. 3-49aFig. At this time, make sure that there is no gapFig. A. Installing the side panel 3-13-3.Wiring the ceiling panelB. Installing the intake grille 3-13-5.Other A. Check after installationTable Concealed Duct Type U TypeFig. Table3-15.Suspending the Indoor Unit enough to support the weight of the unitIt is important that you use extreme care in supporting the indoor unit inside the3-17.Checking the Drainage 3-16.Installing the Drain PipingFig. Fig.short the pin on the indoor control board Fig. How to read the diagram3-18.Increasing the Fan Speed Fig.Table Concealed Duct High-StaticPressure Type D TypeFig. 3-20.Suspending the Indoor Unit enough to suport the weight of the unitIt is important that you use extreme care in supporting the indoor unit inside theHow to Read the Diagram 3-21.Installing the Drain Piping3-22.Caution for Ducting Work 3-23.Indoor Fan Performance2 Refrigerant tubing • drain hose position 1 Dimensions of suspension bolt pitch and unitCeiling-MountedType T Type Table4 Wall and ceiling side opening position weight of the unit. BeforeFig. 3-25.Suspending the Indoor Unit It is important that you useFig. Fig.Fig. Fig.3-26.Duct for Fresh Air Fig. 3-28.Installing the Drain Piping3-27.Shaping the Tubing Fig.When removing the fastening How to carry out power supply wiringbracket from the cover of the caution to avoid dropping the3-30.Selecting and Making a Hole 3-29.Removing the Rear Panel from the UnitFig. Fig. Wall-MountedType K TypeRemoving the grille b If the Wall is Brick, Concrete or SimilarAttaching the grille 3-33.Preparing the TubingDo not supply power to the unit or operate 3-35.Installing the Drain Hoseit until all tubing and wiring to the outdoor 3-34.Shaping the TubingKHX2452 KHX0752 / 0952 / 1252 /Setting at time of factory shipment Setting at time of4-1.Installing the Outdoor Unit 4. HOW TO INSTALL THE OUTDOOR UNIT4-3.Routing the Tubing and Wiring When routing the tubing, use a5-1.General Precautions on Wiring 5. ELECTRICAL WIRING5-3.Wiring System Diagram Fig. When shipping: In shorted conditionFig. Fig.that all wiring is tightly Loose wiring may causeHow to connect wiring to the terminal For stranded wiring6-1.Connecting the Refrigerant Tubing 6. HOW TO PROCESS TUBINGFlaring Procedure with a Flare Tool Use of the Flaring MethodCautions During Brazing Caution Before Connecting Tubes TightlyUse a reducing valve for the nitrogen cylinder Fig.Tubing Insulation 6-3.Insulating the Refrigerant TubingTwo tubes arranged together Taping the flare nuts6-4.Taping the Tubes 6-5.Finishing the InstallationFig. Fig.7. AIR PURGING higher than the bottom when youManifold gauge Vacuum pumpFig. EvacuationCharging additional refrigerant Use a cylinder designed forFinishing the job R410A8-1.Preparing for Test Run 8. TEST RUNFig. Fig.Fig. 8-2.Test Run ProcedureItems to Check Before the Test Run Fig. 8-3.Outdoor Unit PCB SettingCN33 CN51Examples of the No. of indoor units settings Basic wiring diagram: Example 8-4.Auto Address Setting1 Automatic Address Setting from the Outdoor Unit DIP switch S003 is set to “0.” ONFig. Basic wiring diagram: ExampleIf link wiring is used Automatic Address Setting from Outdoor Unit Automatic Address Setting no compressor operationAutomatic Address Setting from Outdoor Unit Automatic Address Setting in Heating Modesetting in heating mode begins Automatic Address Setting from Outdoor Unit Automatic Address Setting in Cooling ModeDisplay during automatic address setting Checking the indoor unit addresses Remote Controller Test Run Settings8-5.Caution for Pump Down 8-6.Meaning of Alarm MessagesAlarm 9. APPENDIX CARE AND CLEANING9-1. 4-WayAir Discharge Semi-ConcealedType X Type NAME OF PARTSTips for Energy Saving TROUBLESHOOTINGNAME OF PARTS 9-2. 1-WayAir Discharge Semi-ConcealedType A TypeCARE AND CLEANING Outdoor unit TROUBLESHOOTINGTips for Energy Saving NAME OF PARTS CARE AND CLEANINGShould the power fail while the unit is running TROUBLESHOOTINGTips for Energy Saving Avoid DoNAME OF PARTS 9-4. Ceiling-MountedType T TypeCARE AND CLEANING or soot TROUBLESHOOTINGTips for Energy Saving CARE AND CLEANING 9-5. Wall-MountedType K Type NAME OF PARTSor soot TROUBLESHOOTING