Test Print Mode | SATO CL408-412e specs

Unit 4: Printer Configuration

TEST PRINT MODE

Provides the specific sequence of events required by the operator, the printer, and the printer’s software for a test label to be printed. Test labels are designed to identify failures in configuration, adjustments problems, and mechanical defects.

Use the keys of the printer’s operator panel to select and enter the required options. Refer to the Menu Definition Tables in the following chapter to provide an explanation of each menu screen.

				FEED + POWER



				TEST PRINT MODE
				CONFIGURATION
						BARCODE
					HEADCHECK
Scrolls						MEMORY
Scrolls						FACTORY
options						FACTORY


					LINE

	Memory		Configuration
	FEED		Barcode
			Headcheck
			FEED

TEST PRINT SIZE

XXCM

	Scrolls	LINE
	options
		FEED

Factory

FEED

PRINT SIZE SMALL LARGE

LINE

Scrolls options

Test

printing begins

PRESS FEED KEY

TO STOP PRINTING

FEED

Test

printing stops

Power printer off and then on again to exit

Figure 4-8, Test Print Mode

CL408-412e Supplemental Manual

4-13

PN: 9001159A

Image 48

SATO CL408-412e manual Test Print Mode

Contents

Printer Sato America, Inc Table of Contents Printer Configuration Troubleshooting Maintenance AppendixOffset Introduction About this Manual Equipment Damage General Description 1a, Primary Components Control Features Operator Panel Features LED Definition Operator Panel Technical Data Physical Characteristics PowerEnvironmental Processing Command SensingMedia Ribbon Character Font Capabilities Barcode Capabilties UPC A/EMSI Postnet Installation Unpacking & Parts Identification Unpacking & Parts Identification Printer Installation Site LocationCable Connection Media Selection Media & Ribbon Loading 3b, Fan-fold Media Loading Operational Mode Selection TEAR-OFF ModeContinuous Mode Label Print Direction Interface Specifications Accessories Installation unit for guidanceInterface Selection RS232C HIGH-SPEED Serial Interface PIN Direction Signal Definition OFFOFF ODD Even None OFF ON/X-OFF READY/BUSY Cable Requirements DB9 Host DirectionPrinter ON/X-OFF Cable Requirements Specifications PIN Assignments Signal DirectionIEEE1284 Parallel Interface ACK Dipswitch Settings SettingUniversal Serial BUS USB Local Area Network LAN Ethernet Software Specifications Accessory EXT Connector PIN AssignmentsDirection Signal Definition 802.11G Wireless Switch SettingLED Indicator Status Description Ssid EXT Accessory Port READY/BUSY Interface Signals Low 0V when the printer is offline +24V +/- 10% @2A Power for external devicesWaiting 8b, Timing Chart Repeat Print Interface Signals ALL InterfacesCable Requirements Receive Buffer Control 50 of 500 items in the history buffer Accessories Installation Interface Installation Printer Configuration Unit 4 Printer Configuration Dipswitch Settings DSW1 Default SettingsDSW1 Configuration Configuration Function DescriptionDSW1 Function DSW3 Default Settings Configuration Modes Normal Mode Advanced Mode Advanced Mode User Download Mode User Download Mode Service Mode Service Mode Card Mode Card Mode Protocol Initialization Mode DSW7 on Line + Feed + Power Counters Mode Counters Mode Test Print Mode Test Print Mode Boot Download Mode Yes Flash Memory Download Mode 10, Flash Memory Download Mode Default Setting Mode 11, Default Setting Mode HEX Dump Mode Online QTY Maintenance Mode 13, Maintenance Mode Normal Mode Table Advanced Mode TableMenu Definition Tables Menu Description Real-time clock is not installed Point respectivelyStream including graphics and 2D barcodes Proportional is contemporarily preferred Service Mode Table As most important where conflicting data exists Is only a transitional menu screen for the Service ModeLanguages are provided as options Operator to manage the expanded memory card Card Mode Table Transitional menu screen to access the Counters Mode Allows the selection of which counter to be viewed to resetOr use Is the initial screen of the Test Print Mode Configuration The printer’s configuration settingsBarcode The printer’s installed barcodes Font The contents of the installed fonts Also prompts the operator on how to proceed Reboot the printer to return to normal operationSelect the Interface option for a standard download To proceed to the Factory Mode Print bufferClear Clear its Eeprom of all data Maintenance Mode Table Page. These are the only two options Troubleshooting Error Signal Troubleshooting Troubleshooting Table No Printed Image Printer Creates a Blank LabelIncorrect Label Positioning Smeared Print Images Interface Troubleshooting CHK Troubleshooting Step LAN Ethernet Interface Test Print Troubleshooting Power Test Label Printing Sample Test Label Maintenance Cleaning Procedures PRINTER, Excersize Care to Prevent Print Head Damage Replacement Procedures Print Head Replacement 1b, Print Head Replacement Interface Board Replacement Interface Board Replacement Fuse Replacement Fuse Replacement Adjustment Procedures Print Head Balance Adjustment Print Head Alignment 5a, Print Head Alignment Ribbon Guide Alignment Head Balance and Print Head Alignment Label Sensor Positioning Label Sensor Positioning Ribbon Spindle Tensioning Ribbon Spindle Tensioning Operational Adjustments Potentiometer DESCRIPTION/PROCEDUREDarkness Print Base Reference Position Appendix Print Setup Dimensions Direction Label Reference Position Diagram Label Reference Position Glossary GlossaryAscii Bytes Collection of 8 bits used in the binary system Being its mating halfIs a plug male and the other is a socket female Half. The core is convexed and the cavity is concaved DPI DramEeprom Data transmission, seven additional bits are required Power Tag would typically have to be removed from its objectNext label for printing To attach two or more objects LCD LED Potentiometer Or voltage divider Primary RAM RF/AISRF/DC Rfid ROM RPMSAM Sbpl Sram Glossary