11, Default Setting Mode | SATO CL408-412e instruction

Unit 4: Printer Configuration

DEFAULT SETTING MODE

The Default Settings Mode allows the operator to return the printer to the configuration state as received from the factory. Use the printer’s keys to select and enter the required options.

Refer to the Menu Definition Tables in the following chapter to provide an explanation of each menu screen.

LINE + FEED + POWER

DEFAULT SETTING

YES NO

	Scrolls	LINE
	options	LINE
	options

		Yes			No
		FEED			FEED

Printer returned to default settings

DEFAULT SETTING

COMPLETED

Power printer off and then on again to exit.

No action, no change

Figure 4-11, Default Setting Mode

CL408-412e Supplemental Manual

4-16

PN: 9001159A

Image 51

SATO CL408-412e manual 11, Default Setting Mode

Contents

Printer Sato America, Inc Table of Contents Troubleshooting Printer Configuration Maintenance AppendixOffset Introduction Equipment Damage About this Manual 1a, Primary Components General Description Operator Panel Features LED Definition Control Features Operator Panel Technical Data Processing Physical CharacteristicsPower Environmental Ribbon CommandSensing Media Character Font Capabilities Postnet Barcode CapabiltiesUPC A/E MSI Installation Unpacking & Parts Identification Unpacking & Parts Identification Printer Installation Site LocationCable Connection Media & Ribbon Loading Media Selection 3b, Fan-fold Media Loading Operational Mode Selection TEAR-OFF ModeContinuous Mode Label Print Direction RS232C HIGH-SPEED Serial Interface Interface SpecificationsAccessories Installation unit for guidance Interface Selection OFF ON/X-OFF PIN Direction Signal DefinitionOFF OFF ODD Even None ON/X-OFF Cable Requirements READY/BUSY Cable Requirements DB9Host Direction Printer ACK SpecificationsPIN Assignments Signal Direction IEEE1284 Parallel Interface Local Area Network LAN Ethernet Dipswitch SettingsSetting Universal Serial BUS USB Software Specifications Accessory EXT Connector PIN AssignmentsDirection Signal Definition Ssid 802.11G WirelessSwitch Setting LED Indicator Status Description READY/BUSY Interface Signals EXT Accessory Port Low 0V when the printer is offline +24V +/- 10% @2A Power for external devicesWaiting 8b, Timing Chart Repeat Print Interface Signals ALL InterfacesCable Requirements 50 of 500 items in the history buffer Receive Buffer Control Interface Installation Accessories Installation Printer Configuration Unit 4 Printer Configuration Dipswitch Settings DSW1 Default SettingsDSW1 Configuration Configuration Function DescriptionDSW1 Function DSW3 Default Settings Normal Mode Configuration Modes Advanced Mode Advanced Mode User Download Mode User Download Mode Service Mode Service Mode Card Mode Card Mode DSW7 on Line + Feed + Power Protocol Initialization Mode Counters Mode Counters Mode Test Print Mode Test Print Mode Yes Boot Download Mode 10, Flash Memory Download Mode Flash Memory Download Mode 11, Default Setting Mode Default Setting Mode Online QTY HEX Dump Mode 13, Maintenance Mode Maintenance Mode Menu Description Normal Mode TableAdvanced Mode Table Menu Definition Tables Proportional is contemporarily preferred Real-time clock is not installedPoint respectively Stream including graphics and 2D barcodes Service Mode Table Operator to manage the expanded memory card As most important where conflicting data existsIs only a transitional menu screen for the Service Mode Languages are provided as options Card Mode Table Transitional menu screen to access the Counters Mode Allows the selection of which counter to be viewed to resetOr use Font The contents of the installed fonts Is the initial screen of the Test Print ModeConfiguration The printer’s configuration settings Barcode The printer’s installed barcodes Also prompts the operator on how to proceed Reboot the printer to return to normal operationSelect the Interface option for a standard download Clear its Eeprom of all data To proceed to the Factory ModePrint buffer Clear Page. These are the only two options Maintenance Mode Table Troubleshooting Error Signal Troubleshooting Troubleshooting Table Smeared Print Images No Printed ImagePrinter Creates a Blank Label Incorrect Label Positioning CHK Troubleshooting Step Interface Troubleshooting LAN Ethernet Interface Power Test Print Troubleshooting Test Label Printing Sample Test Label Maintenance PRINTER, Excersize Care to Prevent Print Head Damage Cleaning Procedures Print Head Replacement Replacement Procedures 1b, Print Head Replacement Interface Board Replacement Interface Board Replacement Fuse Replacement Fuse Replacement Print Head Balance Adjustment Adjustment Procedures 5a, Print Head Alignment Print Head Alignment Head Balance and Print Head Alignment Ribbon Guide Alignment Label Sensor Positioning Label Sensor Positioning Ribbon Spindle Tensioning Ribbon Spindle Tensioning Operational Adjustments Potentiometer DESCRIPTION/PROCEDUREDarkness Print Base Reference Position Appendix Direction Print Setup Dimensions Label Reference Position Label Reference Position Diagram Glossary GlossaryAscii Half. The core is convexed and the cavity is concaved Bytes Collection of 8 bits used in the binary systemBeing its mating half Is a plug male and the other is a socket female Data transmission, seven additional bits are required DPIDram Eeprom To attach two or more objects PowerTag would typically have to be removed from its object Next label for printing LED LCD Or voltage divider Primary Potentiometer Rfid RAMRF/AIS RF/DC Sbpl ROMRPM SAM Sram Glossary