SATO GL408/412E manual Setting and select that configuration as the Power-Up, Media Control menu

		Unit 4: Printer Configuration
		ZGL EMULATION MODE (TABLE 4-11)
MENU		DESCRIPTION
	Label Buffer Size. This option allows the label buffer size to be set. The buffer is used to store the
	data from ^XA up to ^XZ for command processing. The maximum buffer size cannot exceed the
	amount of available memory in the system. If a menu value greater than the amount of memory
	available is selected, the menu value will be set to the amount available. To increase the amount
Label But Size
	of available memory, increase the Glob Mem Adjust setting in the Printer control menu.
560K Bytes*
	The new buffer size only takes effect upon powering on, so perform a Save Config for the new
	setting and select that configuration as the Power-Up.
	The allowable range is 160 to 3600 Kbytes, and the factory default is 560 Kbytes.
	Determines the method of setting the Label Length.
	•	Enable - factory default. Label length will be determined by the ^LL command if it is present.
		If the ^LL command is not present, it will be based on the Label Length value in the Quick
Host Form Length
		Setup or Media Control menu.
Enable*
	•	Ignore - label length as determined by the ^LL command is ignored.
	•	Disable - label length will be determined by the Label Length value in the Quick Setup or
		Media Control menu.
	The ^LS command specifies a horizontal offset to be added to all label element positions. The
	Left Position option displays the value specified by the ^LS command and provides an alternative
Left Position
	method for specifying the horizontal offset.
0 dots*
	The factory default is 0 dots.
	The valueof this option specifies a vertical offset to be added to all label element posiotns in dots
	per inch. For example, if the value is 3 and the current form length is 6 inches, then 18 dots will be
Top Position
	added to the element’s vertical position.
0 dots/inch*
	The allowable range is -100to +100 dots/inch, and the factory default is 0 dots/inch.
	The ^JM command determines the apparent print resolution of the printed label.
	•	Full - factory default. The output is printed normally. The Resolution mode option displays
		and selects the current setting associated wit the ^JM command.
Resolution Mode
Full*	•	Half - if selected by the ^JM command, the printed output of a 300 dpi printer
		matches that printed by a 150 dpi printer (half resolution). This essentually doubles
		the size of the label image, including label dimensions.
	Allows the vertical adjustment feature to be enabled or disabled.
	•	Disable - factory default. Vertical density adjustment will not take place.
Vertical Adjust
Enable*	•	Enable - is active and will use the Vertical Density value selected.
	If Vertical Adjust is enabled, this option allows to fine tune the vertical print density (in the paper
	motion direction) on printers with 203 or 300 dpi print heads. The result is that the vertical posiiton
	and height will be changed accordingly. Selecting a greater vertical density value causes the
Vertical Density
	image to compress or expand vertically on the label.
207 dpi*
	•	203 DPI - the allowable range is 201 to 220 dpi, and the factory default is 207 dpi.
	•	300 DPI - the allowable range is 301 to 330 dpi, and the factory default is 300 dpi.
	This command saves the printed label image by name for later recall as part of a label definition
	and determines the internal format to be used. The storage location is determined by the option
	selected in the Storage Select menu.
IS Label Fmt	•	List Format - factory default. Used for most applications due to its greater efficiency of data
List Format*
		process.
	•	Bitmap Format - used in applications that frequently recall the saved label image. Results in
		greater print speed.

GL408-412e Operator Manual 4-71 PN: 9001163A