Copier Installation | Sharp AR-207 manual

GETTING STARTED Copier installation

COPIER INSTALLATION

Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved.

If the copier is moved from a cool place to a warm place, condensation may form inside the copier. Operation in this condition will cause poor copy quality and malfunctions. Leave the copier at room temperature for at least 2 hours before use.

Do not install your copier in areas that are:

●damp, humid, or very dusty

●exposed to direct sunlight

● poorly ventilated

●subject to extreme temperature or humidity changes, e.g., near an air conditioner or heater.

The copier should be installed near an accessible power outlet for easy connection.

Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements.

Also make certain the outlet is properly grounded.

Connect the copier to a power outlet which is not used for other electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

Be sure to allow the required space around the machine for
servicing and proper ventilation.	4" (10cm)

A small amount of ozone is produced within the copier during operation.The emission level is insufficient to cause any health hazard.

NOTE:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average concentration.

However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated area.

8

Image 10

Sharp AR-207 operation manual Copier Installation, Do not install your copier in areas that are

Contents

AR-207 Safety Precautions Contents Introduction Conventions used in this manual Main Features Part Names and Functions Part Names and Functions Paper Size indicators Interrupt key and indicator pZoom indicator p.24 Alarm indicators Original Size Enter key and indicators Start key and indicatorPreset Ratio selector keys and indicators Auto Paper Select indicator Do not install your copier in areas that are Copier InstallationAlso make certain the outlet is properly grounded Do not touch the photoconductive drum green portion Gently lift and pull out the paper tray until it stops Loading Copy PaperPush the paper tray firmly back into the copier Loading Copy Paper Press the Start key and then the Paper Size Enter 11 key Enter your account number using the numeric keys When copying is completed, press the Audit Clear KeyAuditing Accounts Stream feeding mode Power onTurn the power switch on Normal Copying Ensure that the one-sided to one-sided copying mode is Adjust the copy densityNormal Copying Press the Start key Set the number of copies using the numeric keysTwo-sided copies from one-sided originals Ensure that no original is left on the original table Set the number of copies and press the Start key Two-sided copies from two-sided originalsSet the number of copies and press the Start key One-sided copies from two-sided originals Original has been set in the document feeder tray Close the document feeder cover Ensure that the desired paper tray is selected Copying from the Original Table Copying from the original table Select the desired parameter using the numeric keys Setting image rotation in duplex copyingPress the Original to Copy key REDUCTION/ENLARGEMENT/ZOOM Automatic Ratio, then press REDUCTION/ENLARGEMENT/ZOOMManual To increase the ratio Bypass Feed special paper Unfold the bypass tray Bypass Feed special paper SORT/GROUP Sort modeGroup mode Offset stack SORT/GROUP Copying in the sort modeSet the originals face up in the document feeder tray Interrupting a Copy RUN Automatic Exposure Adjustment Toner Save Mode To enter the toner save mode, press the light key XY Zoom Press the copy ratio display key Use the Preset Ratio selector , keys and zoom XY Zoom Reverse Press the Dual page Copy key Dual page CopyPlace the originals on the original table with the center Rotation Copying 2 x 11 is performed, the image cannot be rotated 1 or 4 Enter the desired pattern number using a numeric key Press the 2 in 1 / 4 in 1 key to complete the selection Erase Press the Erase key to select the desired erase modeEnsure that the desired copy paper size is selected Erase Place the original in the document feeder tray or on Until the Margin Shift indicator will blinkMargin Shift To confirm or set the location of the margin, press Toner Cartridge Replacement Push the toner cartridge lock release lever and pull Than 5 seconds Toner Cartridge ReplacementToner cartridge life Press the light key Misfeed in the Rspf First confirm the misfeed location Misfeed in the copier Misfeed RemovalMisfeed in the bypass tray If the misfed original cannot be removed in steps 1 Removing it Push gently on both sides of the front cover to open Cover Turn the roller rotating knob in the direction Arrow Misfeed in the upper paper tray Close the side cover by pressing the handle on Cover Close the paper tray Close the lower side cover Misfeed in the lower paper trayPull out the lower paper tray and remove the misfed paper If the misfed paper is not seen in , gently lift Maintenance Required Developer Required List of user programs User ProgramsProgram Program name Description User Programs Setting the user programsEnter a program number using the numeric keys Program name Program No To continue with other user programs, press the key Select the desired setting using the numeric keys Settings for auditing accountsEnter a 3-digit account number using the numeric keys Number to be changed Use the copy ratio display key to select the account Use the copy ratio display key to select the account Number Press and hold down the 0 key Program No Resetting account Preheat mode Power Save ModesAuto power shut-off mode Copying from the preheat mode Power Save ModesSetting the power save modes Copying from the auto power shut-off mode Original table and document feeder cover User MaintenanceBypass tray with a soft, clean cloth dampened with Bypass tray paper feed roller Charger cleaner out by holding the tab User MaintenanceTransfer charger cleaning Gently lift and pull out the upper paper tray and take Problem Solution Copier TROUBLE? Copier TROUBLE? ProblemCOPY/FAX key Self-diagnostic function Example Supplies Types and sizes of copy paper Proper storage SuppliesGenuine supplies statement Store the supplies in a location that is Specifications Rspf Specifications Reversing Single Pass Feeder Optional Equipment System Configuration Part Names Loading copy paper Misfeed removal Specifications AR-DE5 Index Index Product Material Safety Data SheetEmergency and First Aid Procedures Routes of Entry Specific Gravity Vapor Pressure Ignition TemperatureSpecial Fire Fighting Procedure Vapor Density Health Hazards IngredientsProportion Medical Conditions Generally Aggravated by Exposure Evaporation Rate Not applicable Viscosity Appearance Fine powder Color Black Odor Odorless Memo For users in the USA Sharp Corporation