User User Options | Siemens 6210, 6220 instruction

USER (User Options)

CLOCK (Set Time and Date)	page 55
SPDIAL (Speed Dial)	page 55
PAUSE (Dialing Pause)
DIR (Call Directory)	page 57
RING (Personal Ringing)	page 59
TONE (Ringing Tone)
OFFHK (Off-Hook Ringing)
NORMAL
SINGLE (Single Burst)
CONTROL (Ringing Control)
ALWAYS (Ring Immediately)
NEVER (Never Ring)
WAIT2 (Wait 2 Ring Cycles / 12 seconds)
WAIT3 (Wait 3 Ring Cycles / 18 seconds)
WAIT4 (Wait 4 Ring Cycles / 24 seconds)
WAIT5 (Wait 5 Ring Cycles / 30 seconds)
WAIT6 (Wait 6 Ring Cycles / 36 seconds)
WAIT7 (Wait 7 Ring Cycles / 42 seconds)

PREF (Off-hook Call Preference – National ISDN only) . page 61 RING (Answer Ringing Call)

IDLE (Select Idle Call Appearance)

NONE (Manual Call Appearance Selection)

VOICE (Voice Mode)	page 62
HAND (Handset)
HEAD (Headset)
VOLUME
RCV+/- (Receive Volume Up/Down)
XMT+/- (Transmit Volume Up/Down,
Headset only)
DISPLY (Display Contrast)	page 63
+ (Increase Contrast)
- (Decrease Contrast)
PASSWD (Call Log Password)	page 64
SET, CLEAR

Tone Commander 6210/6220 User Manual

73

Image 76

Siemens 6210, 6220 user manual User User Options

Contents

Page Contents Appendix a Ordering Isdn Service Introduction General FeaturesModels/Options Controls and Indicators OFF Page Operation Placing a CallSelecting a Call Appearance Dialing Last Number Redial Using DSS Keys Answering a CallCall Preference Ringing Control Displaying Call Appearance Information Bridging a Shared Call AppearanceHolding Calls Transferring Calls Conferencing CallsDSS Transfer Conferencing a New Call Using Network Features Conferencing a Held CallDropping the Last Party Terminating a Conference Using the Call Log Viewing the Call Log Call Menu DIR LOG IDSelect Call LOG Type Unans Answd OUT Delete Dial Time Back Shortcut to the Unanswered Call Log Dialing a Call Log Entry Using the Call Directory What is the Call Directory?Dialing from the Call Directory Directory PAGE1\ Placing and Answering Calls Using the SpeakerphoneMuting the Microphone Enabling/Disabling Using Voice AnnounceReceiving Voice Announce Calls Using a Headset Adjusting the Receive VolumeAdjusting the Ringer Volume Headset Mode Operation Installation Ordering Isdn Service6210T/6220T Installation Set the Termination Switches on the Telephone and NT1 Line and Power Connections Basic MultipointShort Multipoint Extended Point-to-Point Pin # Signal Wire Color Handset/Headset 6210U/6220U Installation Set the Termination Switch on the Telephone Volt 6210U Power Supply 6220U Rotating the Base Wall MountingAttaching to a wall mount jack Configure the Set L3OK SWITCH=5ESS NI-XInitialization L1OK No Parameter Download Press Setup to Configure Firmware UpdatesUsing Local Inspect to Verify Keys Automatic Button Detection 5ESS Custom Isdn only Customize your Phone Personal Ringing Label the Set Installation Options Installation Options MenuSetup Menu Instl Admin User Pots Installation Options \ Spid Param Keys Spid Entry Bksp Clear Configuring Keys Parameter DownloadStarting a Download Enabling/Disabling Automatic Download CA/DN FA DSS Spdial UnusedCall Appearance / Directory Number Keys Bksp Orig Reserv Automatic Call Appearance Selection Feature Activator Keys 10=NETWORK FA#59 Call Bkspcall DSS Keys Bksp Clear Pause Bksp Clear Pause FA Speed Dial KeysBksp Pause FA Terminal Mode Terminal MODE=CACH Ekts Cach Basic Installation Password Installation Password SET ClearNEW Password Bksp Verify Password Bksp Password Cleared Removing the PasswordWhat to do if you lose your password Reset ALL Setup OPTIONS? YES no Reset to Factory Default SettingsALL Settings Cleared Voice Announce Voice Announce OptionsSelecting CA/DN Keys Select VA Keys GREEN=VA, RED=AVAILABLE Selecting Incoming Directory Numbers Bksp Clear ALL Selecting Alerting Patterns ALERTING=ANY Normal Dist Intcom PRI Automatic Muting Automatic MUTE=ON On OFF Administration Options Administration Options MenuAdministration Options \ Inspct Vers Test Diag Administration Options \ Restart LOG Local Inspect Local InspectKeys Call Appearance/Directory Number Key Feature Activator, Conference, Transfer, or Drop Key Originating DN? YES \ RESERVED=OUT/PRIORITYOriginating DN? no RESERVED=NOT Reserved DSS Key Message Waiting Indicator Directory NumbersMESSAGE=NETWORK FI#63 Speed Dial Key Version Version Serial H/W S/WSerial Number Hardware Version Optional Equipment Version MODEL6030X Button Expan Display and LED Indicators TestTerminal Test Disply Keys DISPLAY/LED Test LCD RED Green OFF Press Each KEY to Test Or GO OFF-HOOK to Exit KEY Test Passed Press ANY KEY to Exit6030X Expansion Module Press Each KEY on Press Done to Exit Restart Diagnostic DisplayRESTART/CLEAR Call LOG? YES no View LOG Entries Error Param Clear Viewing the Error and Download LogsClearing Logs User Options User Options MenuUser Options Clock Spdial DIR Ring User Options Setting Up Speed Dial Keys Setting the Time and DateBKSPAM/PM Speed Dial Programming Smart Pauses Select a Softkey PAGE1\ Setting Up the Call DirectoryBksp Clear Move Number Bksp Clear Pause Name Moving a Directory EntryPick NEW Softkey PAGE1\ Deleting a Directory Entry Personal Ringing Options Ringing ToneRinging TONE=5 USE Keypad Keys Off-Hook Ringing Options Ringing Control for Individual Call Appearances Call Preference Options Call PREFERENCE=RINGING Ring Idle None Handset/Headset Configuration Handset/Headset ModeVoice MODE=HEADSET Hand Head Volume Preset Volume Levels Receive handset and headset Adjusting the Display ContrastTransmit headset only Setting a Call Log Password Call LOG Password SET ClearCreating/Changing Your Password Verify NEW Password Bksp Removing the Password Troubleshooting Inoperable Telephone Recovery Procedures With full initialization, proceed to the following steps Telephone Configuration Troubleshooting CA/DN trouble Check Fix Ordering Isdn Service Setup WizardWhere to Go for Help Ordering Manually Recommended Button Assignments Network Assignment Button # Setup Menu Tree Instl Installation Options Admin Administration Options User User Options Pots 6002TA Analog Pots Port Options Warranty and Service Tone Commander Product Warranty Specifications Factory Default Settings Parameter Default Value National Isdn 5ESS Custom Isdn Important Safety Instructions UL/FCC StatementsPage FCC Requirements Page Page 13-102800 Rev. L