Installation Options Menu | Siemens 6220, 6210 instruction

Installation Options

Options in this section are typically set at the time of installation. Many options can be set automatically by the AutoSPID, Automatic Switch Detect, and Parameter Download features, if supported on the network.

The following options can be changed from the Installation Options menu:

•	SPID	•	Installation Password
•	Parameter Download	• Reset to Default Settings
•	Terminal Mode	•	Voice Announce

•Key Configuration

Installation Options Menu ________________

You can enter the Installation Options menu when the phone is idle.

Setup Press the Setup key.

SETUP MENU

INSTL ADMIN USER POTS

Select INSTL.

INSTALLATION OPTIONS \

SPID PARAM KEYS

More When Æ appears in the top line of the display, you can press the More4key to see additional menu selections.

INSTALLATION OPTIONS \

MODE PASSWD RESET VA

Note: The POTS option is only available when the 6002TA Analog Port Terminal Adapter is installed.

The PARAM and MODE options are only available with National ISDN.

28Tone Commander 6210/6220 User Manual

Image 31

$Siemens 6220, 6210 Installation Options Menu, Setup Menu Instl Admin User Pots, Installation Options \ Spid Param Keys$

Contents

Page Contents Appendix a Ordering Isdn Service Introduction General FeaturesModels/Options Controls and Indicators OFF Page Dialing OperationPlacing a Call Selecting a Call Appearance Last Number Redial Ringing Control Using DSS KeysAnswering a Call Call Preference Displaying Call Appearance Information Bridging a Shared Call AppearanceHolding Calls Conferencing a New Call Transferring CallsConferencing Calls DSS Transfer Terminating a Conference Using Network FeaturesConferencing a Held Call Dropping the Last Party Using the Call Log Delete Dial Time Back Viewing the Call LogCall Menu DIR LOG ID Select Call LOG Type Unans Answd OUT Dialing a Call Log Entry Shortcut to the Unanswered Call Log Directory PAGE1\ Using the Call DirectoryWhat is the Call Directory? Dialing from the Call Directory Placing and Answering Calls Using the SpeakerphoneMuting the Microphone Enabling/Disabling Using Voice AnnounceReceiving Voice Announce Calls Headset Mode Operation Using a HeadsetAdjusting the Receive Volume Adjusting the Ringer Volume Set the Termination Switches on the Telephone and NT1 InstallationOrdering Isdn Service 6210T/6220T Installation Extended Point-to-Point Line and Power ConnectionsBasic Multipoint Short Multipoint Handset/Headset Pin # Signal Wire Color Set the Termination Switch on the Telephone 6210U/6220U Installation Volt 6210U Power Supply 6220U Rotating the Base Wall MountingAttaching to a wall mount jack L1OK Configure the SetL3OK SWITCH=5ESS NI-X Initialization Automatic Button Detection 5ESS Custom Isdn only No Parameter Download Press Setup to ConfigureFirmware Updates Using Local Inspect to Verify Keys Personal Ringing Customize your Phone Label the Set Installation Options \ Spid Param Keys Installation OptionsInstallation Options Menu Setup Menu Instl Admin User Pots Bksp Clear Spid Entry Enabling/Disabling Automatic Download Configuring KeysParameter Download Starting a Download Bksp Orig Reserv CA/DN FA DSS SpdialUnused Call Appearance / Directory Number Keys Automatic Call Appearance Selection 10=NETWORK FA#59 Call Bkspcall Feature Activator Keys Bksp Clear Pause DSS Keys Bksp Clear Pause FA Speed Dial KeysBksp Pause FA Terminal MODE=CACH Ekts Cach Basic Terminal Mode Verify Password Bksp Installation PasswordInstallation Password SET Clear NEW Password Bksp Password Cleared Removing the PasswordWhat to do if you lose your password Reset ALL Setup OPTIONS? YES no Reset to Factory Default SettingsALL Settings Cleared Select VA Keys GREEN=VA, RED=AVAILABLE Voice AnnounceVoice Announce Options Selecting CA/DN Keys Bksp Clear ALL Selecting Incoming Directory Numbers ALERTING=ANY Normal Dist Intcom PRI Selecting Alerting Patterns Automatic MUTE=ON On OFF Automatic Muting Administration Options \ Restart LOG Administration OptionsAdministration Options Menu Administration Options \ Inspct Vers Test Diag Call Appearance/Directory Number Key Local InspectLocal Inspect Keys DSS Key Feature Activator, Conference, Transfer, or Drop KeyOriginating DN? YES \ RESERVED=OUT/PRIORITY Originating DN? no RESERVED=NOT Reserved Speed Dial Key Message Waiting IndicatorDirectory Numbers MESSAGE=NETWORK FI#63 Hardware Version VersionVersion Serial H/W S/W Serial Number MODEL6030X Button Expan Optional Equipment Version DISPLAY/LED Test LCD RED Green OFF Display and LED IndicatorsTest Terminal Test Disply Keys Press Each KEY on Press Done to Exit Press Each KEY to Test Or GO OFF-HOOK to ExitKEY Test Passed Press ANY KEY to Exit 6030X Expansion Module Restart Diagnostic DisplayRESTART/CLEAR Call LOG? YES no View LOG Entries Error Param Clear Viewing the Error and Download LogsClearing Logs User Options User OptionsUser Options Menu User Options Clock Spdial DIR Ring Setting Up Speed Dial Keys Setting the Time and DateBKSPAM/PM Smart Pauses Speed Dial Programming Select a Softkey PAGE1\ Setting Up the Call DirectoryBksp Clear Move Number Deleting a Directory Entry Bksp Clear Pause NameMoving a Directory Entry Pick NEW Softkey PAGE1\ Off-Hook Ringing Options Personal Ringing OptionsRinging Tone Ringing TONE=5 USE Keypad Keys Ringing Control for Individual Call Appearances Call PREFERENCE=RINGING Ring Idle None Call Preference Options Preset Volume Levels Handset/Headset ConfigurationHandset/Headset Mode Voice MODE=HEADSET Hand Head Volume Receive handset and headset Adjusting the Display ContrastTransmit headset only Verify NEW Password Bksp Setting a Call Log PasswordCall LOG Password SET Clear Creating/Changing Your Password Removing the Password Inoperable Telephone Recovery Procedures Troubleshooting With full initialization, proceed to the following steps CA/DN trouble Check Fix Telephone Configuration Troubleshooting Ordering Manually Ordering Isdn ServiceSetup Wizard Where to Go for Help Network Assignment Button # Recommended Button Assignments Instl Installation Options Setup Menu Tree Admin Administration Options User User Options Pots 6002TA Analog Pots Port Options Tone Commander Product Warranty Warranty and Service Specifications Parameter Default Value National Isdn 5ESS Custom Isdn Factory Default Settings UL/FCC Statements Important Safety InstructionsPage FCC Requirements Page Page 13-102800 Rev. L