Siemens 6210, 6220

Tone Commander 6210/6220 User Manual 43

Automatic Muting

Select MUTE.

Select ON to automatically mute the microphone during a

Voice Announce call, or OFF to enable two-way

conversations.

Press the Done key after selecting the muting option.

AUTOMATIC MUTE=ON

ON OFF

Done

Contents

Main Contents Page Introduction General Features ________________________ Models/Options _________________________ Page Page Page Operation Placing a Call ___________________________ Selecting a Call Appearance Automatic Call Appearance Selection Manual Call Appearance Selection Page Using DSS Keys Answering a Call ________________________ Call Preference Ringing Control Bridging a Shared Call Appearance ________ Displaying Call Appearance Information ____ Holding Calls ___________________________ Transferring Calls _______________________ DSS Transfer Conferencing Calls ______________________ Conferencing a New Call Conferencing a Held Call Using Network Features __________________ Call Forwarding Using the Call Log _______________________ Page Page Using the Call Directory __________________ Using the Speakerphone _________________ Placing and Answering Calls Muting the Microphone Using Voice Announce ___________________ Enabling/Disabling UNANS VA ON Receiving Voice Announce Calls Using a Headset ________________________ Headset Mode Operation Optimizing the Phone to Match Your Headset Adjusting the Receive Volume _____________ Adjusting the Ringer Volume ______________ Installation Ordering ISDN Service ___________________ 6210T/6220T Installation __________________ Set the Termination Switches on the Telephone and NT1 Tone Commander 6210/6220 User Manual 19 Line and Power Connections NT1 6210T or 6220T 6210T or 6220T Set NT1 termination to 50 ohms. 6210T or 6220T Handset/Headset 6210U/6220U Installation _________________ Set the Termination Switch on the Telephone Basic Multipoint: Extended Point-to-Point: Line and Power Connections Handset/Headset Wall Mounting __________________________ Rotating the Base Attaching to a wall mount jack Configure the Set _______________________ Initialization SPID Entry L1:OK L2:OK TEI:123 L3:OK SWITCH=5ESS NI-X ENTER PRIMARY PHONE # 785-1243 |BKSP Firmware Updates Using Local Inspect to Verify Keys NO PARAMETER DOWNLOAD PRESS SETUP TO CONFIGURE Customize your Phone ___________________ Label the Set ___________________________ Installation Options Installation Options Menu ________________ SPID Entry _____________________________ ID=42534910000101 |BKSP CLEAR Parameter Download _____________________ Configuring Keys _______________________ Page Automatic Call Appearance Selection Feature Activator Keys 10=NETWORK FA#59 (CALL) |BKSP CALL DSS Keys 1001 |BKSP CLEAR PAUSE 08=DSS/DN# 425-349-1001 |BKSP DSS# Speed Dial Keys 5553452341 |BKSP CLEAR PAUSE FA |BKSP PAUSE FA 5551234P1P12 |BKSP CLEAR PAUSE Terminal Mode __________________________ Installation Password ____________________ Page Reset to Factory Default Settings __________ Voice Announce _________________________ Selecting CA/DN Keys VOICE ANNOUNCE OPTIONS KEYS DNs ALERT MUTE SELECT VA KEYS GREEN=VA, RED=AVAILABLE Selecting Incoming Directory Numbers CALLING DN#1=4253491* |BKSP CLEAR ALL Page Page Administration Options Administration Options Menu _____________ Local Inspect ___________________________ Keys Call Appearance/Directory Number Key LOCAL INSPECT KEYS DNs MESSAGE 01=CA/DN# 555-349-1012 \ Page Page Version ________________________________ Page Test ___________________________________ Page Diagnostic Display ______________________ Restart ________________________________ Viewing the Error and Download Logs ______ Clearing Logs VIEW LOG ENTRIES ERROR PARAM CLEAR User Options User Options Menu ______________________ Setting the Time and Date ________________ Setting Up Speed Dial Keys _______________ 04-27-99 11:16AM |BKSP AM/PM Speed Dial Programming Smart Pauses DIAL#=5553491000 |BKSP CLEAR PAUSE Setting Up the Call Directory _______________ SELECT A SOFTKEY PAGE1\ Jim G Home DIRECTORY NAME:Steve |BKSP CLEAR MOVE NUMBER Page Personal Ringing Options ________________ Page Call Preference Options __________________ CALL PREFERENCE=RINGING RING IDLE NONE Handset/Headset Configuration ____________ Receive (handset and headset) Transmit (headset only) Adjusting the Display Contrast ____________ CONTRAST [{{{{{ ] (-) (+) Setting a Call Log Password ______________ Removing the Password PASSWORD CLEARED What to do if you lose your password Troubleshooting Inoperable Telephone Recovery Procedures Page Telephone Configuration Troubleshooting Appendix A Ordering ISDN Service Setup Wizard Ordering Manually Key Assignments Where to Go for Help Recommended Button Assignments Appendix B Setup Menu Tree INSTL (Installation Options) ADMIN (Administration Options) USER (User Options) POTS (6002TA Analog POTS Port Options) Options in this menu are described in the 6002TA Analog Port Terminal Adapter User Manual. Appendix C Warranty and Service Tone Commander Product Warranty Appendix D Specifications Factory Default Settings Parameter Default Value (National ISDN) Default Value (5ESS Custom ISDN) Appendix E UL/FCC Statements Important Safety Instructions SAVE THESE INSTRUCTIONS FCC Requirements